Strand Vision.Net DMX User manual

1
QUICK START GUIDE
VISION.NET DMX MODULE
(1 UNIVERSE)
443581626889
OVERVIEW
This document provides installation and operation instructions for the following product(s):
PRODUCT NAME ORDER CODE
Vision.Net DMX Module (1 Universe) 53904-401
INSTALLATION AND SET UP
DIN RAIL MOUNTING
To mount Vision.Net DMX Module (1 Universe) on compatible TS35/7.5
DIN rail:
Step 1. Tilt the module backwards slightly.
Step 2. Fit the module over the top hat of the DIN rail.
Step 3. Slide module down until fully engaged with the top hat.
Step 4. Push the module forward to engage to the DIN rail fully.
Step 5. Gently rock the module back and forth to assure it’s locked
in place.
To remove unit(s) from DIN rail:
Step 1. Turn o and disconnect wiring.
Step 2. Gently pry the module from the bottom using a slotted
screwdriver if required.
SURFACE MOUNTING
To mount Vision.Net DMX Module (1 Universe) on a surface:
Step 1. Determine appropriate orientation of your module for your application - vertical or horizontal.
Step 2. Using the surface mount bracket as a template mark the location of the keyholes on the mounting
surface.
Step 3. Install appropriate fasteners for your application. The keyholes accept two #6 rounded head screws.
Step 4. Remove DIN rail bracket from module by removing two Phillips head screws with a #2 driver. Save
bracket for future use.
Step 5. Attach surface mount bracket to module using two Phillips head screws observing the desired orien-
tation.
Step 6. Hang the module on the fasteners installed in Step 3 and hand-tighten.
3
12
4
Click

2
QUICK START GUIDE
VISION.NET DMX MODULE
(1 UNIVERSE)
443581626889
WARNINGS AND NOTICES
When using electrical equipment, basic safety precautions should always be followed including the following:
• For indoor, dry locations use only. Do not use outdoors.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to
tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition
and void warranty.
• Not for residential use. Do not use this equipment for other than intended use.
©2022 Signify Holding. All rights reserved.
All trademarks are owned by Signify Holding or their respective owners. The
information provided herein is subject to change, without notice. Signify does
not give any representation or warranty as to the accuracy or completeness of
the information included herein and shall not be liable for any action in reliance
thereon. The information presented in this document is not intended as any
commercial offer and does not form part of any quotation or contract, unless
ot
h
e
r
w
i
se
ag
r
eed
by
S
i
g
nif
y
. D
ata
subject
to
c
h
a
n
ge
.
CUSTOMER SERVICE
If you have any questions regarding this product,
please contact Customer Service by phone at
[phone] or by email at entertainment.
[e-mail].
C
US
CM
2
REQUIREMENTS
• The Vision.Net DMX Module (1 Universe) requires
power from a separate +24 V DC power source
connected with 16-28 AWG wire.Consult a Strand
representative for specifying an appropriate rated
power supply.
• The recommended wire for interfacing Vision.Net is
Belden 1583a
• (Cat5e, 24 AWG, Solid).
To connect Vision.Net DMX Module (1 Universe) to Digital
Input Sources:
Step 1. Remove applicable screw-down connector
from module.
Step 2. Prepare wire and insert into connector
observing polarity of the source, if required. Use a slotted screwdriver to tighten the screw down
terminals.
Step 3. Align and evenly re-insert the connector back into the module.
SURFACE MOUNT BRACKET CAN
BE MOUNTED HORZONTALLY
OR VERTICALLY AS SHOWN
LED INDICATORS
RS232: Flashes green status of inputs. Display using MODE button.
USB: Flashes green status of inputs. Display using MODE button.
CONFIGURATION BUTTONS
MODE: toggles LED display between RS232 and USB.