Streamline R-5040-67CIFSBCH-FM Troubleshooting guide

FREESTANDING BATHTUB SERIES
OWNER'S MANUAL &
INSTALLATION GUIDE
streamlinebath.com
QUESTIONS ON PRODUCT, INSTALLATION, RETURNS? PLEASE CONTACT
1 (310)-935-0028
[e-mail]
READ ENTIRE INSTALLATION GUIDE
PRIOR TO INSTALLING THE BATHTUB
THIS BATHTUB SHOULD ONLY BE
INSTALLED BY A CERTIFIED PLUMBER
CAUTION! TWO PEOPLE ARE REQUIRED
TO LIFT THE BATHTUB

These products must be installed by a fully insured and licensed plumber only.
Installation of any product by anyone other than fully insured and licensed plumber shall void limited warranty.
We are not responsible for any local code compliance for this product.
Building and plumbing codes may vary state-to-state.
Streamline shall not be held liable for any and all incidental damages or flood caused due to use of this product.
Streamline shall not beheld liable for any and all fees stemming from cost of installation, re-installation, removal,
subsequent damage, or transportation in a case of a product defect.
Please note:
Different bathtubmodels have different drain models. Please see the next page to determinewhich drain model
applies to the bathtub model that you have purchased.
Silicone
Bathtub
(Pre-installed)
Model A1866
Adjustable Key Measuring Tape Safety GlassesPencil Level Bar
PRIOR TO INSTALLING
TOOLS REQUIRED
WHAT'S IN THEBOX
N-DWF-CH
N-DWF-GLD

DRAIN MODEL COMPATIBILITY
ACRYLIC FREESTANDING BATHTUB
Model
Model A1866
N-DWF-CH
N-DWF-GLD
R-5040-67CIFSBCH-FM R-5041-67CIFSPCH-FM R-5042-67CIFSWH-FM
R-5043-67CIFSRDY-FM R-5080-66CIFSWH-FM R-5081-60CIFSWH-FM
R-5180-72CIFSWH-FM
R-5140-66CIFSWH-FM R-5200-72CIFSWH-FM R-5201-61CIFSWH-FM
R-5320-67CIFSGR-FM
R-5300-71CIFSWH-FM R-5340-66CIFSGLD-FM R-5360-72CIFSBCH-FM
R-5381-67CIFSBCH-FM
R-5380-67CIFSGLD-FM R-5480-60CIALWH-FM
R-5260-67CIFSGLD-FM R-5400-67CIFSWH-FM

DRAIN DIAGRAMS
No ITEM Qty
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
16
17
9
Cover
Cover gasket
Cartridge
Strainer
Waste upper gasket
Waste lower gasket
Connector
Coupling nut
Nut
Washer
Tee
Pipe
Overflow body
Tapered rubber gasket
Overflow upper gasket
Overflow plate
Pin Bolt
Taic piece
Flange
1
1
1
1
1
1
1
1
1
3
3
1
1
1
1
1
1
1
1
Model A1866
1
2
3
4
5
6
7
8
9
10
11
12
12
13
13
14
15
16

DRAIN DIAGRAMS
No ITEM Qty
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
16
17
9
Cover
Cover gasket
Cartridge
Strainer
Waste upper gasket
Waste lower gasket
Connector
Coupling nut
Nut
Washer
Tee
Pipe
Overflow body
Tapered rubber gasket
Overflow upper gasket
Overflow plate
Pin Bolt
Taic piece
Flange
1
1
1
1
1
1
1
1
1
3
3
1
1
1
1
1
1
1
1
Model: N-DWF-CH
Model: N-DWF-GLD

BATHTUB INSTALLATION
1. Ensure that the floor at the installation site has sufficient floor support and is level.
2. Waterproofing the floor is highly recommended.
3. Determine the location of the drainpipe on the floor by taking measurements of the drain and waste
location underneath the unit. Clean the drain hole area in preparation of setting the drain. The area
should be dry & free from any debris.
4. Remove the bathtub from its box. It is recommended that the bathtub is carried by a minimum of
two people. Ensure to carry and set down the bathtub only in the upside-down position.

5. Gently place the bathtub in the upside-down position on a tarp or cardboard sheet in order to avoid
contact with any rough surface.
Below is the installation for drain A1866;
For drain N-DWF-CH/GLD, please skip to page 11
6. Loosen the nuts & washers from the metal frame. Adjust the leveling feet to align with the bathtub’s
bottom as well as the floor and then tighten the washer and nuts.
7. Ensure to mark all positions of leveling legs on the floor using a pencil. Move the bathtub into the
desired location near the drainpipe.

8. Before proceeding with installation, push thepop up into acloseposition andfill the bathtub above
the overflow [Note: some models may not have an overflow] to test for overflow and drain leakage.
9. Proceed to place the provided flexible drain hose into the floor drain.
10. Please note, the flexible hose is a basic way that we provide to connect to the end plumbing in a
home. The plumbing installation in every home differs, so please consult with a certified plumber
to see if the plumbing in your home is compatible with using a basic flexible hose.
11. Seal the connection by using a PVC pipe sealant to join the parts together.

12. Apply siliconealong the bottom of the bathtub In order to create an airtight seal. Then apply abead
of tub & tile caulk around the edges of the base.
13. With the bathtub now in place, wipe off any excess silicone, tub & tile caulk where the bathtub meets
thefloor.
14. Allow for up to 24 hours for the adhesive material to set.
24h

8. Take the strainer, place silicone sealant around it, and then place it into the drain hole ensuring
a tight connection with the drain ell & gasket. Use silicone sealant. DO NOT use plumbers putty to seal.
9. Insert the tailpiece into the trap inlet using the O-ring, coupling nut, & flange. The tailpiece may
need to be cut for proper fit. 1''-2'' of the tail piece shoudl fit inside the trap. Slip the flange over the tailpiece
and slide down to the floor.
10. Assemble the tee section to the tailpiece, overflow, & drain ell using the coupling nuts and O-rings
that are provided.
Silicone
Sealant
Strainer
O Ring
Coupling Nut
Flange
Trap Inlet
O Ring
Overow Ell
Tee
Coupling Nut
Tailpiece
Gasket
Drain Ell

11 . Attach the tapered rubber gasket to the overflow ell. Align the overflow ell with the overflow hole &
secure the drain to the tub with overflow plate and screw provided.
12 . Make sure a watertight seal exists on all bath drain connections.
End home plumbing
Floor
Cover Drain Pipe
Tapered Rubber Gasket
Overow Plate