STRIKEMASTER Honda 35CC LITE User manual

LIMITED WARRANTY
STORAGE
! !
The following are storage recommendations only. Because of today’s fuels StrikeMaster cannot guarantee results.
ENGINE OIL
• Change crankcase oil before the start or at the end of each season or 50hrs of use with fresh StrikeMaster API SM (as a minimum)
OW-20 4-Cycle Synthetic Engine Oil.
CLEAN AND STORE EACH SEASON
• At the end of the season, add fuel stabilizer to the fuel tank. Be sure to keep the tank approximately 1/4 full of gasoline.
• Run for 2-3 minutes then turn o.
• Remove the spark plug, pour about 2 cc (about 4 drops) engine oil into the cylinder, slowly pull the starter handle of the recoil starter 2 or 3
times, reinsert and tighten the spark plug.
• Slowly pull the recoil starter handle until resistance is felt, and leave it in that position.
• Spray WD-40 or oil on the blades and screws to help reduce rust or corrosion.
• Clean the engine thoroughly with a clean cloth, put a cover on and store the engine indoors in well ventilated low humidity area.
• Store all auger styles with blade guard attached.
• At the beginning of the next season, drain gas tank of old fuel and add fresh winter blend gasoline.
OPERATION
! !
1. To start, rotate ON/OFF switch to the ON position. Slide choke lever to the START position. Press primer bulb 5-10 times or until fuel is visible
in return line. Pull recoil short and quick. As soon as engine fires, slide choke lever to run position and allow engine to idle for 1-2 minutes
before drilling.
2. This product produces considerable cutting force that is felt by the operator. Make sure your feet are firmly planted and that the handles
are held firmly.
3. Push the throttle lever downward to increase the engine speed. As the engine speed increases the centrifugal clutch will engage and the
auger will begin to rotate.
4. During the operation of cutting, the auger could possibly stop if it comes in contact with a foreign object or if it binds in the hole. Be prepared
at all times to release the throttle lever to avoid rotation of the handle assembly.
5. Hold the unit in a vertical position with your right hand pushing downward to open throttle and your left hand firmly holding
the opposite handle.
6. Use caution when removing or replacing blade guard. The cutting blades on the ice augers are razor sharp. Use extreme care when handling.
7. Always keep the blade guard on auger, except when in use.
8. The use of this auger by children or adult under 100lbs. is not recommended.
9. Stop engine if you notice a dierence in the operating characteristics of this machine.
10. Always stop the engine before any contact with the auger, even when clearing ice blockage.
11. Always check to make sure the throttle system is moving freely and returning to idle.
12. Turn o this machine when traveling from fishing site to fishing site
Lithium LazerTM
Chipper Mag
Chipper Lite

HondaTM 35 CC LITE
Owner’s Manual
WARRANTY SERVICE
Visit our website for up to date warranty service centers.
www.strikemaster.com
Continued satisfying performance from your StrikeMaster power ice auger may be assured by applying a
minimum amount of preventive maintenance.
The warrantor’s obligation shall be limited to repairing or replacing any part, which upon examination by StrikeMaster, is determined to be
defective.  This obligation begins on the date of purchase (as evidenced by a product receipt) and continues for a period of ONE YEAR after
purchase (“warranty period”), with the exception of engines and parts subject to wear and tear.  This warranty is non-transferrable; warranty
registration must be completed online or via USPS within 30 days of purchase to validate warranty. The warranty does not apply if product has
been negligently used, misused, altered, damaged in an accident or if periodic maintenance has not been performed. Customer is responsible for
shipping and transportation charges to the nearest warranty repair center.
Company warrants that Product, other than engines and parts subject to wear and tear, will perform substantially in accordance with the
accompanying written materials [owner’s manual] for a period of ONE YEAR. In the case of engines and parts subject to wear and tear, please refer
to the chart below. Parts subject to normal wear and tear are not covered by warranty including: air filter, fuel filter, any rubber part that comes in
contact with fuel, clutch, spark plug, starter (recoil), 12 volt batteries and blades. In the event applicable law imposes any implied warranties, the
implied warranty period is limited to ONE YEAR from the date reflected on the product receipt. Some jurisdictions do not allow such limitations on
the duration of an implied warranty, so the above limitation may not apply.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE COMPANY AND AUTHORIZED SERVICE CENTERS DISCLAIM ALL OTHER
WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE WITH REGARD TO THE PRODUCT AND WRITTEN MATERIALS [OWNER’S MANUAL]. THIS LIMITED WARRANTY GIVES
CUSTOMER SPECIFIC LEGAL RIGHTS. CUSTOMER MAY HAVE OTHER RIGHTS DEPENDING ON THE JURISDICTION.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY OR AUTHORIZED SERVICE CENTER BE LIABLE
FOR ANY DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITATION, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL OR INDIRECT DAMAGES FOR
PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIARY
LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. IN ANY CASE, THE COMPANY’S AND AUTHORIZED REPAIR CENTER’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS
AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT. BECAUSE SOME JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
LIMITED WARRANTY
Limited Warranty coverage
(with receipt/proof of registration)
30-Day
Warranty
90-Day
Warranty
1-Year
Warranty
2-Year
Warranty
3-Year
Warranty
Wear & tear parts X
12-Volt Battery X
StrikeMaster parts X
Solo engine X
Honda engine X
Lithium Lazer motor X
Lithium Lazer battery X

HondaTM 35 CC LITE
Owner’s Manual
You MUST add crankcase oil to
your new Auger prior to your first use!
We recommend using the bottle of
StrikeMaster API rated SM (as a minimum)
OW-20 4-Cycle Synthetic Engine Oil included.
For longer life of the engine, continue to use the
required API rated SM (as a minimum) OW-20
4-Cycle Synthetic Engine Oil.
It is recommended that everyone
who uses this product should read
this StrikeMaster Owner’s Manual.
ATTENTION: PRIOR TO FIRST USE
For best performance, idle
engine for 1-2 minutes before
you start drilling.
SM14
!!
LIMITED WARRANTY

2
STRIKEMASTER®
Ice Augers
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED COULD ENDANGER
THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS
IN THIS MANUAL AND ANY PROVIDED WITH OR ON THE EQUIPMENT ON WHICH THIS ENGINE IS USED BEFORE
ATTEMPTING TO OPERATE YOUR STRIKEMASTER POWER ICE AUGER.
ATTENTION !!
!
Record the engine serial number, engine type and date purchased in the
space below. Also, please return the enclosed WARRANTY CARD or submit
your information at www.strikemaster.com to validate your limited warranty.
Model: Honda 35cc Lite
Engine Serial Number __ __ __ __ -__ __ __ __ __ __ __ Engine Type __ __ __ __
Date Purchased ______ / ______ / ______
Ice Fishing has become one of the fastest growing and most popular winter sports, allowing the ardent angler
the opportunity to enjoy their favorite outdoor activity year round.
When you purchased a StrikeMaster® power ice auger, you selected a product that has gained a reputation as
the quality leader since 1946. There is no doubt that this year’s model is the finest ever produced by StrikeMaster.
Your new StrikeMaster ice auger has all of the most wanted features in a power ice auger, to assure many years of
enjoyable ice fishing. Some of these features such as workmanship, engineering excellence, and dependability have
long been standards at StrikeMaster. Your new power ice auger boasts many new features while retaining the best
features developed in previous years to enhance your ice fishing experience and add to your
satisfaction in selecting StrikeMaster.
We know that you are anxious to go fishing and use your new power ice auger, but before you go fishing, it is
important and to your advantage to spend a few minutes getting acquainted with your new StrikeMaster power
ice auger. There is no better way to acquaint yourself with the product than to read the Owner’s Manual and
operating instructions. A few minutes spent studying this manual before your first ice fishing outing will be
time well spent.
!! IMPORTANT NOTICE
DO NOT REMOVE THE GREEN INTAKE GASKET.
See photo for location on engine. Not only will removing the
green intake gasket void the warranty, if removed the engine
will not work properly and could cause damage.
If removed, replacement of the green intake gasket is NOT
covered under Honda or StrikeMaster limited warranties.
For service contact your local authorized Honda Engine
Dealer or visit www.strikemaster.com for more information
by clicking the “Find Service Centers” button to search
service centers by zip code. For more information from
Honda click the “Visit Honda” button.
DO NOT REMOVE
Green Intake Gasket

CHECKING/ADDING GASOLINE & OIL !!
!!
1. DO NOT use this product for any purpose other than cutting ice fishing holes. Ice augers are precision cutting tools built
for the ice fisherman, and must be properly maintained and handled with caution during both cutting and transporting.
When not in use, always store with blade guard attached.
2. DO NOT use attachments other than those available from the manufacturer.
3. DO NOT alter this product in any manner; doing so is dangerous and voids all warranties.
4. DO NOT allow children or adults weighing under 100 lbs. to operate this equipment.
5. DO NOT operate under the influence of drugs or alcohol.
6. DO NOT allow your body, loose clothing, drawstrings, scarves, hats or other materials to come in contact with the Powerhead,
Starter Assembly or Auger (Drill) unit at any time.
7. DO NOT operate if, upon pulling the starter rope or after drilling holes, the auger (drill) unit rotates or if the rope pulls hard.
Have the unit checked by a qualified mechanic.
8. DO NOT allow the engine to run or operate while moving or transporting to another location.
9. DO NOT continue to use this product in the event of mechanical or electrical failure.
10. This product produces considerable cutting force that is felt by the operator. Make sure your feet are firmly planted and that
the handles are held firmly while operating this product.
11. Always check the operation of the throttle system to ensure the carburetor control is completely returning to the
idle position when the throttle lever is released.
12. CHECK cutting blade screws and collar bolt before and after each use to make sure they are tight.
13. During operation, the auger unit could possibly stop. Be prepared at all times to release the throttle lever.
14. The cutting blades on the ice auger are razor sharp. Use extreme care when handling.
15. After use, the auger blades should be wiped dry and oiled to extend blade life.
It is recommended that everyone who uses this product should read this
StrikeMaster Owner’s Manual before operating.
IMPORTANT SAFEGUARDS
3
Fuel Tank
Cap
Oil
Gauge
The Honda (GX35 engine) is a non-application specific manual. Any further technical engine guidelines that are not covered in the StrikeMaster
Owner’s Manual, refer to the Honda Owner’s Manual. Unit shipment also includes correct amount of StrikeMaster API rated SM (as a minimum)
OW-20 4-cycle synthetic engine oil for initial fill (3.4 oz.). Honda GX35 engine crankcase capacity has a maximum oil capacity of 3.4 oz.
DO NOT OVERFILL.
Also, running the engine with a low oil level can cause engine damage. This type of damage is not covered by the Distributor’s Limited Warranty.
See Honda Owner’s Manual for other information such as air cleaner, spark plug, and fuel filter.
Your new 4-stroke auger engine does NOT come filled with oil or gasoline.
You will need to add StrikeMaster API rated SM (as a minimum)
OW-20 4-Cycle Synthetic Engine Oil to the crankcase reservoir and
unleaded gasoline to the fuel tank prior to your first use. Using a gas/oil mixture
will damage the motor.
Honda Motor Co. requires you use only API rated SM (as a minimum)
OW-20 4-Cycle Synthetic Engine Oil with the Honda 35cc Lite auger engine.
See included Honda Owner’s Manual for step by step instructions or go to:
http://cdn.powerequipment.honda.com/engines/pdf/manuals/00X37Z6J6100.pdf
to download a digital copy.
Suggested position to check oil
Add or check oil at bottom edge of hole, (Fig 1 right), while in position
as shown here or on page 9 of the Honda Owner’s Manual.
Use a 5-1/2" tall block for 8" auger
Use a 4-3/4" tall block for 10" auger
Fig 1

INITIAL ASSEMBLY
! !
Carefully remove blade
guard and make sure
blade bolts are tight.
Remove metric allen
wrench taped to the
neck of auger and
unscrew the collar
bolt from auger.
(Use 8mm closed
end wrench)
The large and small
holes from each
component must line
up before installing
the collar bolt.
Push down and twist
to line up holes.
After assembly is complete, you
can conveniently store your allen
wrench on the underside of the
throttle pedal.
It is recommended that the collar
bolt be checked and torqued firmly
before and after every use.
2
2a
3a
3a
2a
Large
Holes
3
Output Shaft
!
13
4
Metal Collar
Allen
Wrench
Collar Bolt
Plastic
Collar
2
Lazer
Blade
1
4
4
bolt be checked and torqued firmly
4
Allen Wrench
Storage
It is recommended to grease
inside collar and transmission
output shaft on the powerhead.
Standard automotive wheel
bearing grease is suggested.
Insert drive shaft into auger and
install collar bolt.
Collar bolt inserts into the large
hole, passing through the drive
shaft and threads into small hole
of metal collar. Tighten bolt. Some
wiggle is normal between the power
head and auger. Tighten often.
STOP ENGINE
! !
After completing the cutting of an ice fishing hole, STOP the engine by allowing the engine to return to idle and
moving the ignition switch to the OFF position. If the engine fails to stop, move the choke lever to the FULL CHOKE
position to kill the engine. Always check the throttle system to ensure the carburetor throttle lever is returning to
the idle position. If the ignition switch should fail, DO NOT operate until the ignition switch has been repaired by a
qualified mechanic.