StrongHandTool RHINO CART User manual

RHINO CART®(Part No. TDQ54830)
1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
ASSEMBLY INSTRUCTIONS
Part No.
TDQ54830
Tabletop
Size
48” x 30” 410 LBS
Tabletop
Thickness
5/8”
Hole
Diameter
0.625”
Grid
Pattern
2” x 2”
Table
Height
36”
Table
weight
Charge right through your most
challenging projects!
RHINO CART®
MOBILE FIXTURING STATION
S
t
r
o
n
g
H
a
n
d
T
o
o
l
s
®
S
t
r
o
n
g
H
a
n
d
T
o
o
l
s
®
PA
TENTE
D

1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
Part No. TDQ54830
RHINO CART®
» Carefully unpack all parts and components and compare to the Parts List inventory below.
Read all assembly instructions before beginning to assemble your Rhino Cart®.
During assembly, do not tighten bolts until all components are properly aligned, then tighten fully.
We suggest that you use at least 2-3 people to assemble the cart.
T2 x 10 T3 x 5 W x 1T4 x 5T1 x 1
Item QtyNo. Item QtyNo.
A Tabletop and Frame Assembly 1
B Divider Panel 1
C Middle Tray 1
D Square Hole Pegboard (yellow) 1
E Lower Tray 1
F Tool Rack 1
H Handle 1
J1 Casters (swiveling) with locking brake 2
J2 Casters (fixed) 2
L1 Legs (left) 2
L2 Legs (right) 2
P Leveling Pads 4
Q1 Button Head Screws M10 x 16 24
Q2 Button Head Screws M10 x 20 16
Q3 Socket Head Cap Screws M10 x 30 2
Q4 Button Head Screws M6 x 16 14
R1 Hex Jam Nuts M10 24
R2 Hex Lock Nuts M10 16
R3 Hex Nuts M10 2
R4 Hex Nuts M6 14
S Washers 16
T1 Support Rack 1
T2 Single Hooks 10
T3 Double Hooks 5
T4 Plastic Bins 5
W Triangle Wrench 1
A
F
E
D
C
L2
L1
H
S
Q3
B
Q4
Q4
Q4
J2
J1
Q1
R3
L1
P
P
Q1
P
R1
L2
R4
Q2
R2

1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
Assembly Instructions Part No. TDQ54830
RHINO CART®
» Tools required for assembly : triangle wrench (W), phillips screwdriver and pliers.
Install the Square Hole Pegboard (yellow) (D)
between the Divider Panel (B) and the Leg (L1) by
using 6Button Head Screws M6 x 16 (Q4) and Hex
Nuts M6 (R4).
Attach (C) & (D) by 2 pcs of (Q4) and 2 pcs of (R4).
Install the Lower Tray (E) onto the 2 legs by using 4
Button Head Screws M10 x 20 (Q1) and Hex Jam
Nuts M10 (R1).
Meanwhile, attach (B) & (E) by 2 pcs of (Q4) and 2
pcs of (R4).
Place the Tabletop and Frame Assembly (A) on a
flat surface.
Assemble 2 Legs - (L1) and (L2) onto the outer edge
of the frame using 8Button Head Screws M10 x16
(Q1) and Hex Jam Nuts M10 (R1).
Install the Handle (H) using 2 Socket Head Cap
Screws M8 x 20 (Q3) and Hex Nuts M8 (R3).
Install the Divider Panel (B) onto the frame by using
2 Button Head Screws M6 x16 (Q4) and Hex Nuts
M6 (R4). Please note that 2 mounting holes in the
frame should be near the Handle (H) side.
Install the Middle Tray (C) onto the Divider Panel (B)
and the Leg (L2) on the right by using 2 Button Head
Screws M6 x 16 (Q4) and Hex Nuts M6 (R4).
L1
L2
A
Q1
Q1
R1
R1
H
Q3
Q3
R3
1
H
R4
Q4
A
2
B
L1
L2
C
Q4 Q4
4
A
H
Q1
L2
L1
BC
D
R1
Q4
Q4
E
3
A
B
L1
L2
C
Q4
R4
H
Q4
Q4
D
Q4
Q4

Assembly Instructions
1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
Part No. TDQ54830
RHINO CART®
Install remaining two legs (L1) and (L2) onto the
outer edge of the frame using 12 Button Head
Screws M10 x 16 (Q1) and Hex Jam Nuts M10 (R1).
Then fix the Tool Rack (F) onto the legs by using 2
pcs of (Q4) and 2 pcs of (R4).
Maintenance
Keep the cart clean for optimal performance. Wipe away dust and
debris from the tabletop and legs.
Safety
ALWAYS wear safety goggles, gloves, and other appropriate safety
items for protection. Use the cart only for it’s intended purpose.
NEVER stand on the cart. Do not drop the cart, throw it, or
otherwise misuse the cart.
Warranty
Each STRONG HAND TOOL® product is warranted to be free from
defects in material and workmanship. Return to place of purchase
for a replacement if warranty applies.
Install 1 pc or 2 pcs of Swiveling Casters (J1) and
Fixed Casters (J2) onto Lower Tray (E) by 16 pcs of
(Q2), (S) and (R2). Install 4 Leveling Pads (P) onto legs
(L1 & L2). Tighten all Hex Head Bolts and Nuts.
Finally, carefully place the cart in the upright position.
Adjusting the Leveling Pads (P) to level the table.
Place small accessories in the Plastic Bins (T4), and
place large accessories such as Clamps on the
Single Hooks (T2) & Double Hooks (T3).
D
T2
T3
T4
T1
To use the Plastic Bins (T4), install Support Rack (T1)
onto the Square Hole Pegboard (D). Then install Plastic
Bins (T4) onto the Support Rack (T1), install Single
Hooks (T2) & Double Hooks (T3) onto the Square Hole
Pegboard (D) according to your requirements.
5
L2
Q1
Q4 R4
R1 L2
L1
L1
Q1 R1
A
H
E
C
D
B
F
R1
Q1
Q4
R4
Q1
R1
6
A
B
J1
J2
C
F
H
Q2
R2
J1
J2
E
S
R2
S
R2
S
R2
S
Q2