Stryker visionpro 0240-031-020 User manual

VisionPro 26"LED Display
VisionPro 26"LED Display: 0240-031-020
VisionPro SYNK 26"Wireless LED Display: 0240-031-000

Table of Contents
Warnings and Cautions ............................................................................................1
About Your Device.....................................................................................................3
Intended Use and Indications for Use �������������������������������������������������������������������������4
Contraindications����������������������������������������������������������������������������������������������������������������4
Package Contents ���������������������������������������������������������������������������������������������������������������5
Device Features��������������������������������������������������������������������������������������������������������������������6
Setup......................................................................................................................... 11
Connections����������������������������������������������������������������������������������������������������������������������� 11
Basic Video Setup�������������������������������������������������������������������������������������������������������������13
Operation................................................................................................................. 14
On-Screen Display (OSD)�����������������������������������������������������������������������������������������������14
OSD Menus�������������������������������������������������������������������������������������������������������������������������16
Troubleshooting���������������������������������������������������������������������������������������������������������������18
Cleaning and Maintenance................................................................................... 19
Technical Specications ........................................................................................ 20
Electromagnetic Compatibility............................................................................ 22
Symbols and Denitions....................................................................................... 25

1
Warnings and Cautions
Please read this manual and follow its instructions carefully� The words warning, caution,
and note carry special meanings and should be carefully reviewed:
Warning: Indicates measures to avoid potential serious injury to the user and the patient�
Caution: Indicates risks to the equipment� Failure to follow cautions may result in product
damage�
Note: Provides special information to clarify instructions or present additional useful
information�
Warnings
To avoid potential serious injury to the user and the patient, please note the following warnings:
1� Read this manual thoroughly and be familiar with its contents prior to using this device�
2� Federal law (United States of America) restricts this device to sale by, or on the order of, a
physician�
3� Carefully unpack the device and check if any damage occurred during shipment�
4� This device is non-sterile and therefore should not be placed in the sterile eld�
5� Do not place the device or any other heavy object on the power cord� Damage to the cable
can cause re or electric shock�
6� To avoid electric shock, avoid removing the bezel�
7� This device should not be used adjacent to or stacked with other devices� If adjacent or
stacked use is necessary, the device should be observed to verify normal operation in the
conguration in which it will be used�
8� Test this device prior to a surgical procedure� This device was fully tested at the factory
before shipment�
9� Do not attempt internal repairs or adjustments not specically detailed in this manual�
Ensure that readjustments, modications, and/or repairs are carried out by persons
authorized by Stryker Endoscopy�
10� Do not put any object into the panel� If this occurs, unplug the device and have it checked by
qualied personnel before operating it any further�
11� Use appropriate caution to prevent contact with uids if the device is being used with a
power supply in patient environments�
12� The use of cables and/or other accessories with this device, other than those specied, may
result in increased emissions or decreased immunity of this device�
Cautions
1� Connect the device to an AC adapter connected to a hospital grade power cord ensuring the
power cord is plugged into a grounded power outlet to achieve grounding reliability�
2� Do not sterilize the device, as the delicate electronics cannot withstand this procedure�
3� Use only the proprietary surgical display power supply for the display� Completely secure the
connection between the DC power cord and the extension cord�
4� Never operate the device immediately after transportation from a cold location to a warm
location�

2
5� To connect to an international power supply, use an attachment plug appropriate for the
power outlet, as outlined in the "Technical Specications" section of this manual�
6� Unplug the device if it is not to be used for an extended period of time� To disconnect the
cord, unscrew the plug rst, then pull the cord out by the plug� Never pull the cord itself�
7� Do not expose the device to moisture or apply liquid cleaners directly to the screen� Spray
the cleaning solution onto a soft cloth and clean gently� For further detail, refer to the
"Cleaning and Maintenance" section of this manual�
8� Allow adequate air circulation to prevent internal heat buildup� Do not place the device
on surfaces (rugs, blankets, etc�) or near materials (curtains, draperies) that may block the
ventilation slots� The device is cooled by natural convection and has no fan�
9� Do not touch the patient with signal input or output connectors� Equipment with SIP/
SOP connectors should either comply with IEC60601-1 and/or IEC 60601-1-1 harmonized
national standards or the combination should be evaluated for safety�
10� To ensure electromagnetic compatibility, refer to the “Electromagnetic Compatibility” section
of this manual� TheVisionPro26”LED Display (0240-031-020) and the VisionPro SYNK 26”
Wireless LED Display (0240-031-000) must be installed and operated according tothe EMC
information provided in this manual�
11� Pay close attention to the cleaning instructions in this manual� A deviation may cause
damage�
12� Do not install the device near sunlight, excessive dust, mechanical vibration, or shock�
13� Do not position the device so that it is dicult to disconnect the power cord from the supply
mains�
14� Do not operate with the glass device screen facing downward�
15� Handle the device with care� Do not strike or scratch the screen�
16� Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the device�
17� Note: This device has been tested and found to comply with the limit for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
device generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. There is no guarantee that interference will not occur in a particular
installation, which can be determined by turning the device o and on. The user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving device.
• Increase the separation distance between the device.
• Connect the device to an outlet on a circuit dierent from that to which the other
device(s) are connected.
• Consult the manufacturer or eld service technician for help.
The warranty is void if any of these warnings or cautions are disregarded�
This product contains electrical waste or electronic equipment� It must not be disposed of as
unsorted municipal waste and must be collected separately�

3
About Your Device
VisionPro 26” LED Display
REF: 0240-031-020
The VisionPro 26” LED Display is a wide screen LED surgical display that can support a maximum
resolution of WUXGA (1920x1200)� The display supports the following video inputs: digital RGB,
analog RGB, serial digital interface (SDI), component video (YPbPr/RGBS), S-video, and C-video/
SOG� It also supports serial communication via the RS232 port�
VisionPro SYNK 26”Wireless LED Display
REF: 0240-031-000
The VisionPro SYNK 26”Wireless LED Display can be used with the optional SYNK Transmitter
(0240-031-010), which allows it to receive a high-denition video signal over a radio-frequency
link�
The display supports the following video inputs: DVI, S-Video, and C-Video/SOG� Once the
wireless functionality is enabled, the display supports a wireless digital RGB video input� The
display also supports a USB port and serial communication via the RS232 port�
Note: The wireless functionality of the VisionPro SYNK 26”Wireless LED Display can only be
enabled via the SYNK Transmitter.
For details and instructions on using the SYNK Wireless Transmitter and the wireless functionality
of the VisionPro SYNK 26”Wireless LED Display, refer to the SYNK Wireless System manual
(P21693)�

4
Intended Use and Indications for Use
The VisionPro SYNK 26”Wireless LED Display and the VisionPro 26”LED Display are intended for
video display during surgical procedures including arthroscopy (orthopedic surgery), laparoscopy
(general and gynecological surgery), thoracoscopy, endoscopy (general, gastroenterological, and
ENT surgery) and general surgery� The display is a non-sterile reusable device not intended for
use in the sterile eld� The display is intended for use by qualied physicians having complete
knowledge of these surgical procedures�
Contraindications
There are no known contraindications for this device�

5
Package Contents
1
2
3
4
5
Reference Part Number Package Contents
10240-031-020
0240-031-000
VisionPro 26”LED Display or
VisionPro SYNK 26”Wireless LED Display
2– (4) M4 × 16 mm VESA screws
3– Hospital-grade AC power cord
40240-031-004 Medical Power Supply
5– Cable Cover
Part Number Optional Accessories
0240-031-002 VisionPro 26”Display Cover
0240-031-004 Medical Power Supply
0240-031-010 SYNK Wireless Transmitter
0240-030-951 15-ft� (5 pin) DC extension cable
0240-030-952 75-ft� (5 pin) DC extension cable

6
Device Features
Front panel
Operate the display using the rotary control located on the front panel� A list of the display
controls and their functions is provided below�
1
2
3710
9
811
4 5 6
1. Display Screen Shows video image�
2. Power switch (soft) Powers the display ON and OFF�
3. Power LED Indicates current status:
Green - Display is powered on or is in screen saver mode
Blinking Red - Display is in sleep mode
Blinking Amber - Over or under voltage
4. Token slot (VisionPro
SYNK 26”Wireless LED
Display only)
Token insertion site used to establish a wireless connection
with the transmitter�
5. Token LED (VisionPro
SYNK 26”Wireless LED
Display only)
Green - Link is established
Amber - Initializing
Blinking Amber - Error, contact service representative
6. Auxillary Connection Supports auxilliary device connections�

7
7. Audio/PIP VisionPro 26” LED Display:
Accesses the Picture in Picture adjustment menu�
VisionPro SYNK 26”Wireless LED Display:
Press twice for Picture in Picture adjustment menu�
Note: Audio functionality is not enabled at this time.
8. Bright Accesses the Brightness adjustment menu
9. Specialty Accesses the Specialty adjustment menu
10. Input Accesses the Input Selection menu
11. Rotary control Accesses the on-screen display and navigates through its
functions�

8
Rear panel
2
4
5
3
9
6
10
8
1
11
12
7
1
1
1. Accessory mounts (3) Provide an access point for mounting optional
accessories�
2. VESA mounting holes Provide access points for mounting the display�
3. Power switch (hard) Powers the input DC power ON and OFF�
4. Power connector Connects to the 24V DC power supply�
5. Handles Aid in display positioning�
Caution: The handles are not intended to bear the
entire weight of the display
6. Cable cover hinges Attach the bottom of the cable cover to the display�
7. Velcro straps Straps aid in cable management�
8. Cable cover thumbscrews Attach the cable cover to the display, and are
tightened or loosened using ngers�
9. Cable cover Covers and conceals cables�
10. Cable cover clips Attach the top of the cable cover to the display�
11. Cable wrap Provides a location for wrapping cables�
12. Locking feature A locking mechanism or cable may be routed here
for security purposes�

9
Cable Cover
Installing the Cable Cover
1� Align the left and right hinges of the cable cover onto the bottom rear of the display�
2� Snap on the top section of the cable cover to the aligning clips�
3� With your ngers, turn the thumbscrews clockwise to tighten and lock the cable cover onto
the display�
Removing the Cable Cover
1� With your ngers, turn the thumbscrews counterclockwise to loosen�
2� Once the thumbscrews are completely loosened, pinch the left and right clips and pull the
cable cover towards you�
3� Remove the cable cover from the left and right hinges�

10
Display Handles
Caution: The handles are intended to aid in positioning the display, not for transporting the
display. The handles should not bear the full weight of the display.
Removing the Display Handles
1� Using a 3mm hex key, loosen the two M4 x 30mm screws and gently pull the handle away
from the display�
Installing the Display Handles
1� Align the handle with the screw holes on the rear of the display�
2� Using a 3mm hex key, install the two M4 x 30mm screws to attach the handle�

11
Setup
Stryker Endoscopy considers instructional training, or inservice, an integral part of this device�
Your local Stryker Endoscopy sales representative will perform at least one inservice at your
convenience to help set up your device and instruct you and your sta on its operation and
maintenance� To schedule an inservice, contact your local Stryker Endoscopy representative after
your device has arrived�
Connections
VisionPro 26” LED Display Connection Ports
Video input and output signals are connected to the rear of the display, as illustrated below:
1 2 3 4 5 6 66687 6669 66610 66611 66612
1. DVI
2. 3G/HD/SD
SDI-in
3. 3G/HD/SD
SDI-out
4. VGA
5. S-Video
6. C-Video/SOG
7. R/Pr
8. G/Y
9. B/Pb
10. H-sync
11. V-sync
12. RS232

12
VisionPro SYNK 26”Wireless LED Display Connection Ports
12 3 6665 6666
4
1. DVI
2. S-Video
3. C-Video/SOG
4. Auxillary Connector
5. USB
6. RS232
Connecting the Power Supply
1� Connect the power supply to the 24V input on the display�
2� Connect the AC power cord to the power supply*�
3� Connect the AC power, using the supplied hospital-grade power cord�
4� (Optional, not shown) Connect an extension cord between the power supply and display�
5� Install cable cover�
* Power supply information: Model Number: BPM150S24F11, Manufacturer: Bridgepower Corp�

13
Basic Video Setup
1
2
1� Route the video output 1 from the camera to the SDC DVI input�
2� Route the video output 1 from the SDC DVI output to the DVI input on the display�
Note: Stryker recommends a backup connection to the camera.

14
Operation
Operate the display using the rotary control and the four buttons located on the front panel� A list
of the display controls and their functions is provided below�
On-Screen Display (OSD)
Accessing the On-Screen Display
1 4
3
2
To use the four front-panel buttons:
1� Audio/PIP (VisionPro SYNK 26”Wireless LED Display):
• Press twice to activate Picture Mode (Picture in Picture, Picture by Picture, Picture on
Picture)
2� PIP (VisionPro 26” LED Display):
• Press to activate Picture Mode (Picture in Picture, Picture by Picture, Picture on Picture)
3� Bright: Activates the Brightness adjustment menu�
4� Specialty: Activates the Specialty adjustment menu�
5� Input: Activates the Input selection menu�
Use the Rotary Control to navigate the on-screen menus once they are activated:
• Push — Accesses/selects on-screen display menu�
• Turn Right/Left — With the on-screen display menu activated, turning increases/decreases
the value of the selected parameter�
• Push and Hold — Exits on-screen display menu�

15
Operating On-Screen Display
The device OSD helps navigate through various device menus�
1� Press the Rotary Control to activate the OSD menu�
2� Rotate the Rotary Control to move up or down through the menu�
The parameter is highlighted when selected�
3� Press the Rotary Control to enter the next level OSD�
4� Rotate the Rotary Control to increase or decrease the value of the selected parameter, or to
make a selection on dierent options�
5� To exit the OSD menu screen from the second or third level OSD menu, select the Exit
option� To completely exit the OSD, press and hold the Rotary Control� If no keys are
pressed, the OSD will automatically exit after the factory-set predetermined time (the time is
customizable)�

16
OSD Menus
Speciality
Menu Item Description Range
Color Temperature* Chooses between color temperatures for Lap A, Lap B,
Arthro A, Arthro B, Standard, PACS, NORM, ENT, GYN�
—
Red Red balance -128–127
Green Green balance -128–127
Blue Blue balance -128–127
Gamma Gamma value 0�1–2�5,
S0, S1, S2
*Color Temperature RGB adjustment is available only for Standard, Arth, and Lap settings� PACS and Norm adjustments are
only avaliable under SOG input�
Audio (Menu not active at this time)
Brightness Settings
Menu Item Description Range
Brightness Increases or decreases the brightness 0–100
Contrast Increases or decreases the contrast 0–100
Phase** Increases or decreases the Phase level 0–100
Chroma** Increases or decreases the Chroma level 0–100
Image Sharpness Sets image sharpness 1–10
Video Sharpness** Increases or decreases the video sharpness 0–100
** Only available under SDI-, S-, or C-video input�
Image Eect
Menu Item Description
Scale Mode Chooses scale mode between Fill All, V-Fill, H-Fill, One-To-One, or
Fill-Aspect
Freeze Frame Enables or disables freeze frame
PIP Enables PIP (picture in picture) function
POP Enables POP (picture on picture) function
PBP Enables PBP (picture by picture) function