Sukkah Center EZ PANEL User manual

• 1 •
THE
EZ PANEL
SUKKAH

• 1 •
PAGE-6
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-1
PANEL ASSEMBLY
All panels (and corner sections on some models) work on a Male/
Female assembly system. Using two Male sides or two Female sides,
will not interlock.
Please ensure the white caps are on the top side of the panel, & the
light wood color side, is on the inside of the sukkah (dark outside).

• 2 •
PAGE-2
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-5
connector
female
connector
CORNER ASSEMBLY
First layout the sukkah panels the way
you would like to set it up.
Position panels at a 45° angle, then
hook male side of panel (1), into the
female front side of panel (2) (to the
left of it), then swing in the direction
of arrow shown in diagram to create
a corner, (use corner section on some
models)
Please ensure the interlock is properly
connected from top to bottom.

• 3 •
PAGE-4
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-3
female
HOW TO CONNECT THE
SIDE PANELS
Place panels side by side,
position the 2 panels at a 135°
angle, then insert male (R)
side of panel (1) into female
side (L) of panel (2), (as shown
in diagram). Swing panels
into place. (see arrow)
Please ensure the interlock is
properly connected from top
to bottom.

• 4 •
PAGE-4
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-3
female
THE ORDER IN WHICH TO CONNECT THE PANELS
Please note doors & windows are interchangeable with a standard panel of the
same size.

• 5 •
PAGE-2
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-5
connector
female
connector
HOW TO CONNECT THE LAST PANEL
1. After completing diagram (10) connect the last panel in the middle on
one side.
2. Push the 2 edges of the last 2 panels outwards, connect the male/female
connection,
3. After ensuring the interlock is properly connected from top to bottom,
pull back in to the straight position.

• 6 •
PAGE-6
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-1
PANEL CONNECTOR INSTALLATION
After each panel to panel connection is made, use the connector (see
diagram) to help keeps the panels together. Connectors should be placed
on the top of the panels, where the 2 panels connect. Use the corners
connector over each corner, to keep the corners straight.

• 7 •
PAGE-COVER
DVD INSERT PROOF
ITEM: SUDEP0002 TITLE: SUKKAH INSTRUCTIONS
PAGE-7
THE
EZ PANEL
SUKKAH
1-855-SUKKAH-1
HOW TO ATTACH THE HANDLES
In the center of the door there are two holes for the purpose of attaching
the handles.
There are two holes on the left side and two holes on the right side.
The holes are closed by plastic plugs.
Please take out the plugs from the holes on the side you wish to open
(the side you opened the hinges) You must screw on the handles from
both sides of the door

• 8 •
SUKKAH WOOD SIZE CHART
In order to strengthen the walls of the Sukkah, place wood inside the
panel connectors around the top perimeter of the Sukkah, see size
chart below.
If you are able to cut the wood, it is best to place the wood from corner
to corner.
Please note on a standard size wood beam, it should be cut 6” shorter
then the size of the sukkah wall.
TOP OF SUKKAH WOOD BEAM PLACEMENT
Place 1 beam holder over the top over of the panel, then clip into place.
Place 1 holder for each side of the 2” x 3” wood beams (2 per beam) on
the top of the Sukkah, beams should be placed approximately every 4’.
Wood beams should hang over the sukkah 1’ on each side.
6’ 5.5’ 2 X 3
8’ 7.5’ 2 X 3
10’ 9.5’ 2 X 3
12’ 11.5’ 2 X 3
14’ 13.5’ 2 X 3