Sullivans 12570 User manual

Thank you for purchasing our
Item #12570
Page 1 www.SullivansUSA.net
HOME HOBBY TABLE
Rev. 11-21-18

HELPFUL HINTS: Read the instructions carefully before starting. Check to see that all parts on the Parts
List are included. It is best to work in a spacious area. Be sure to avoid overtightening.
REPLACEMENT POLICY: Sullivans USA, Inc. will replace any missing or defective parts within 30 days of
purchase. Fax a dated receipt with your contact information and request to 630-435-1532 or e-mail to
[email protected]. To expedite this process, include any parts you may need in your request.
This policy does not apply to damages due to shipping. For further assistance, please call 800-862-8586.
Please note that the no-charge Replacement Policy does not apply to items sold as is, clearance, closeout,
final sale, etc. Any parts requested under these circumstances will be charged to the customer, including
shipping charges. Shipping charges for replacement parts to Alaska, Hawaii or any point outside of the
Contiguous United States are not covered under our policy. Some restrictions apply. See website for
details. If you are outside of the 30 day period, replacement parts are available for purchase.
6
Page 2 www.SullivansUSA.net
PARTS LIST
DESCRIPTION
C1. C2.
PICTUREQTY
Assembly Time: Approximately 1 hour You will need: Phillips Screwdriver
4
2
2
1
24
6
A. Side Boards - 24" x 36”
B. Middle Board - 12" x 36”
C1. Casters
C2. Locking Casters
D. Hinges
E. Allen Bolts - 1/5"
F. Allen Bolts - 1-1/3"
4G. Allen Bolts - 1-1/2"
Rev. 11-21-18

1
Page 3 www.SullivansUSA.net
PARTS LIST
DESCRIPTION PICTUREQTY
H. Allen Key
1
1
2
I. Top Beam
J. Bottom Beam
K. Side Beams
2
2
4
L. Wing Supports
M. Leg Clamps
N. Phillips Screws - 1/2”
14P. Self-Tapping Phillips Screws - 9/16”
2
1
1
O1. Corner Brackets (Bottom)
O2. Corner Bracket (Right)
O3. Corner Bracket (Left)
STOP
DO NOT RETURN TO THE STORE. For assistance with missing or replacement parts,
installation, or any additional information, please call us at 800-862-8586 or email us
at [e-mail].
O1.
O2.
O3.
Rev. 11-21-18

INSTRUCTIONS
K.
C1. C2.
1THE BASE
Parts Needed: C1 (4), C2 (2), G (4), H, I, J, K (2), L (2), O (2), P (8)
2THE TABLE TOP
1A
C1.
L.
1B
1A Screw 1 Caster (C1) and 1 Locking Caster (C2) into the
bolt holes on the bottom of each Side Beam (K).
1B Screw 1 Caster (C1) into the bolt holes on the bottom
of each Wing Support (L).
1C Take the Top Beam (I) and turn the side with 6 holes
down, toward the casters. Use 2 Allen Bolts (G) with
the Allen Key (H) to attach the Top Beam (I) to the Side
Beams (K). Do not overtighten. Be sure that the Locking Casters (C2) are on opposite sides of each other.
1D Insert the top peg of 1 Wing Support (L) into the third
hole on the bottom of the Top Beam (I). Insert the other
Wing Support (L) into the fourth hole, making sure that
the Wing Supports do not face the same way. Take the
Bottom Beam (J) and place the bottom pegs of the Wing
Supports (L) inside the holes on the top of the Bottom
Beam (J). Secure the Bottom Beam (J) to the Side Beams
(K) using the Allen Key (H) with 2 Allen Bolts (G).
To ensure the correct position of the Wing Supports,
face one of the Side Beams (K). The peg on the Wing
Support (L) to your right should be inserted into the
innermost hole at the side closest to you and swing
out away from the table, towards you. See FIGURE 1.
1E Use a Phillips Screwdriver (not included) and 4 Self-Tapping
Phillips Screws (P) to attach a Corner Bracket (O1) to the
Bottom Beam (J) and Side Beam (K). Repeat for other side.
Page 4 www.SullivansUSA.net
G.
L.
I.
K.
G.
K.
K.
C1. C1.
C2.
C2.
I.
H.
1C
L.
L.
K.
K.
J.
P.
O1.
J.
1D
1E
G.
FIGURE 1
Rev. 11-21-18

H.
F.
I. B. A.
K.
2THE TABLE TOP
Parts Needed: A (2), B, D (6), E (24), H, M (2), N (4)
Page 5 www.SullivansUSA.net
INSTRUCTIONS
2A Lay the 2 Side Boards (A) with the Middle Board (B) between them on a clean, protected surface with the pre-drilled
holes facing up. Line up the holes on all the boards.
3ATTACHING THE BASE & TABLE TOP
Parts Needed: F (6), H, O (2), P (6)
3A Carefully flip the base upside down. See FIGURE 2. Line up the base with the pre-drilled holes on the Middle Board
(B) and secure the top two and bottom two holes with 4 Allen Bolts (F). Tighten securely but do not overtighten.
2B Align the 6 Hinges (D) over the predrilled holes on the boards. Be sure that the “bump” is facing up. Secure all of the
Hinges (D) to the Side Boards (A) and Middle Board (B) using the Allen Key (H) and 24 Allen Bolts (E). Tighten securely
but do not overtighten.
Align the 2 Leg Clamps (M) over the pre-drilled holes in the center of the Side Boards (A). Screw the Leg Clamps (M)
in using a Phillips Screwdriver (not included) and 4 Phillips Screws (N). The clamps should face inward toward the
Middle Board (B). Leave the Table Top flat when complete.
A. A.B.
2A
H.
E.
D. N.
M.
2B
3ATTACHING THE BASE & TABLE TOP (CONTINUED)
FIGURE 2
3A
Rev. 11-21-18

Page 6 www.SullivansUSA.net
A.
A.
B.
C1.
C1.
C1.
C1.
C2.
C2.
K.
K.
J.
O1.
I.
L.
L.
O1.
L.
K.
F.
O2.
H.
I.
L.
K.
P.
O2.
I.
INSTRUCTIONS
3B On the right side, attach 1 Corner Bracket (O2) to the Top Beam (I) with 1 Allen Bolts (F) the innermost hole and the
Allen Key (H). Tighten securely but do not overtighten. Use a Phillips Screwdriver and 3 Self-Tapping Phillips Screws (P)
in the 3 remaining holes of the Corner Bracket (O2) to secure. Repeat on left side using Corner Bracket (O3).
3C Fold in the Wing Supports (L) and the 2 Side
Boards (A). Hold tight as you turn the table right
side up, onto the casters.
3D For minor leveling adjustments, remove caster,
rotate the adjusting nut, and screw back into
table leg.
3B
3D
4SAFETY & MAINTENANCE
• Do not place more than 30 pounds on the Side Boards.
• This table is not a toy. Do not let children play on, under, or around the table.
• When using the Side Boards, carefully raise one side at a time, swing out the metal Wing Support, and snap it into the
Leg Clamp. This will provide the maximum table balance and stability.
• Do not move the table when the casters are in the locked position to prevent damaging the casters.
• Use a cloth or sponge with mild soap to clean the table - never use any abrasive material.
• Never rest a hot iron directly on the surface.
STOP
DO NOT RETURN TO THE STORE.
For assistance with missing or
replacement parts, installation, or
any additional information, please
call us at 800-862-8586 or email
[e-mail].
LOCKED
UNLOCKED
Rev. 11-21-18