Sumake ST-M5060 User manual

SUMAKE PNEUMATIC TOOLS
Air Belt Sander (10x330mm)
ST-M5060
SUMAKE INDUSTRIAL CO., LTD
4F,NO.351,Yangguang St.,Neihu District TAIPEI, TAIWAN, ZIP:114-91
Specification:
Free Speed 17,000 r/min
Sanding Pad 3/8” x 13”
(10mm x 330mm)
Air Consumption 17 CFM (480 L/min)
Overall Length 12.6” (320 mm)
Air Inlet (PT) 1/4” (6.35 mm)
Air Hose (I.D.) 3/8” (10 mm)
Air Pressure 90 psi (6.3 bar)
Net Weight 1.8 lbs (0.8 kg)
Noise and Vibration:
Vibration
EN ISO 28927-3 Noise EN ISO 15744 Remark
No Load:
1.64 m/s²
Sound Pressure Level
load: 94 dB(A) Please always
wear ear
protector at
environment
noise level > 80
dB(A) due to
risk of impaired
hearing!
Sound power level
load: 105 dB(A)
Uncertainty
K= 1.5 m/s²Uncertainty
K= 3dB
ST-M5060-S-1905E-D5F

EC DECLARATION OF CONFORMITY
We: SUMAKE INDUSTRIAL CO., LTD.
4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan
declare in sole responsibility that the equipment
Equipment：AIR BELT SANDER (10x330mm)
Model/ Serial No.：ST-M5060
to which this declaration applies, complies with these normative documents:
Machinery Directive: 2006/42/EC
and conforms to the following EN standard,
EN ISO 12100: 2010
EN ISO 11148-8:2011
Name and Signature/Position Date and Place
2022/12/1
Mike Su –Managing Director Taipei, Taiwan
ST-M5060-D-2306C-D5F

Foreword
SUMAKE is a manufacturer and exporter of air
tools since established. We have devote all our
efforts in improving quality and tools’ life. As
well as the noise and vibration of tools. Bring all
of you working efficiences, profits, and enjoy
using the tool is our principle.
Features
1. Finishing of flat surfaces, curved surfaces, and
corner can be freely performed by changing the
shoe.
2. Since it is small, lightweight, and balanced so
that the grinding surface is stable, extremely fine
finishing is possible.
3. The grinding speed can be freely adjusted by
raising or lowing the lever according to the
application.
4. Rear exhaust eliminates flying dust and noise.
Operator‘s instruction
1. Main Applications
Finishing metal carts and products.
Finishing welded surface.
Trimming parts.
Filleting.
Finishing steel cabinets and furniture.
Foundation finishing prior to coating.
Finishing plastic products, glass, and
earthenware.
Finishing stone and decorative wood products.
Finishing sashes and other building material.
Light and medium duty auto, ship and aircraft
finishing.
2. Cautions for Use
2-1 Air pressure
Maximum performance is displayed at the proper
sanding speed, obtainable at a gauge pressure of
6.2 bar. Range-wise, this is an air pressure from
5 to 7 bar (70 to 100 psi)
57
2-2 Air line
Use a 3/8“ air hose between the compressor an
d
the tool . Compressed air is cooled and its wate
r
content separated, as soon as the air leaves th
e
compressor. A portion of the water content
,
however, is condensed in the piping, and ca
n
enter the tool mechanism, and may cause trouble
.
So, install an air filter and on oiler between th
e
compressor and the tool. Use a 3 HP or large
r
compressor for each sander.
Tool
Nipple
Coupler Recoil
hose
Leader
hose
Oiler Regulator
Water
separation Air supply
Drain
daily
2-3 Air hose
Clean the hose with a blast of compressed ai
r
b
efore connecting the hose to air tool. This wil
l
prevent both moisture and dust within the hos
e
from entering the tool and causing possible rus
t
or malfunction. To compensate for unusuall
y
long hose (over 25 ft), the line pressure should b
e
increased accordingly.
Drainage
2-4 Sandpaper
The specification of sandpaper ranges from # 4
0
to # 200. Also note that, the maximum operatin
g
speed which the sandpaper can afford shall b
e
higher than the rotation speed of this tool.
2-5 The approved eye protector,ear-muff
,
mouth-muffle, and gloves shall be worn whe
n
operate this tool.
2-6 The working place shall be ventilative.
2-7 Release the on-off device in the case o
f
energy supply failure.
3. Operation, Adjusting And Replacing
Method
3.1 On-off device
The on-off device is under the grip of this tool. It
is a “hold-to-run” type. You can also adjusting
the running speed by raising or lowering the
lever. This tool stops rotation within few sec,
after releasing the lever. For the sake of safety,
put it on a soft cloth or on hanger after it
completely stops.
3.2 Replace the sandbelt
Disengage and remove the sandbelt from the idle
pulley after pushing the idle pulley in the
direction shown below. Replace a new one and
keep your hand away from the idle pulley. Then
push the tension bar indicated on the drawing
and the sandbelt will be propped into the ready
position.
idle pulley tension bar
3.3 Adjusting tracking
If the sandbelt is not centered on the idle pulley,
adjust the hexagon socket head bolt on the idle
pulley bracket with accessory hexagon wrench
key until centering is correct. Turn the hexagon
socket counter clockwise, the belt is moved
toward the bracket, and vice versa.
clockwise
counterclockwise
bracket
4. Maintenance
4-1 Lubrication
Before connecting the hose , apply 4 or 5 drops
of #60 spindle oil at the air inlet. Use of a thicker
oil can lead to reduced performance or
malfunction. If a
thicker oil is used by accident, wash it away
immediately. Also, every 3 or 4 hours of
operation, oiling is necessary.
4-2 Storage
Avoid storing the tool in a location subject to
high humidity. If the tool is left as it is used , the
residual moisture inside the tool can cause rust.
Before storing and after operation, oil the tool a
t
the air inlet with spindle oil and run it for a short
4-3 Disposal
If the tool is too seriously damaged to be use
d
anymore, drop it in a resource recycling can.
Never drop it into fire.
4-4 Ordering service Parts
For further operational and handling informatio
n
or for replacement of parts and components,
contact the sale agent from whom you purchase
d
the tool or the service division of our company.
*In ordering parts and components, give eac
h
part number, name and quantity.
Warning
1. This tool is not insulted for coming into
contact with electric power source.
2. It is forbidden to use this tool in explosive
atmospheres and do not put any combustible
material near the workpiece since it emit sparks
when grind with metal material.
3. Ensure that the sandbelt is on the central o
f
idle pulley and not to fix too tight/loose. Too
tight tends to break off and too loose tends to
break away.
4. Prevent long hair or loose clothing fro
m
drawing in while operate this tool.
5. Never carry the tool by hose and beware of a
whipping compressed air hose.
6. Rotating action can cause this tool to become
hot. Allow to cool and disconnect air hose before
any changing or adjusting.
ST-M5060-I-1011A-D5

ST-M5060 AIR BELT SANDER (10x330mm)
PARTS LIST
No. Parts No. Description Q'ty No. Parts No. Description Q'ty
1 M5060-01 Idle Pulley 1 31 M5060-31 Cylinder 1
2 M5060-02 Ball Bearing (684ZZ) 2 32 M5060-32 Rear End Plate 1
3 M5060-03 Idle Pully Screw 1 33 M5060-33 Ball Bearing (608ZZ) 1
4 M5060-04 Bracket 10 1 34 M5060-34 O-Ring (S38) 1
5 M5060-05 Set Screw (M3x5) 1 35 M5060-35 Cap 1
6 M5060-06 Hexagon Socket Headless Set Screw 136 M5060-36 Throttle Lever 1
7 M5060-07 Spring 1 37 M5060-37 Spring Pin (Φ3x20) 1
8 M5060-08 Tension Bar 1 38 M5060-38 Valve Body 1
9 M5060-09 Spring Pin (Φ3x10) 139 M5060-39 O-Ring (S11.2) 1
10 M5060-10 Stopper Pin 1 40 M5060-40 O-Ring (P-9) 1
11 M5060-11 Guard Bushing 1 41 M5060-41 Valve Stem 1
12 M5060-12 Tension Spring 1 42 M5060-42 O-Ring (P3) 1
13 M5060-13 Guard Body 1 43 M5060-43 Valve Spring 1
14 M5060-14 Head Cap Screw (M5x15) 1 44 M5060-44 Air Regulator 1
15 M5060-15 Dust Cover 1 45 M5060-45 O-Ring (P7) 2
16 M5060-16 Shoe 10 1 46 M5060-46 External Stop Ring (STW-8) 1
17 M5060-17 Hexagon Socket Headless Set Screw 147 M5060-47 Muffler 2
18 M5060-18 Stopper Spring 1 48 M5060-48 Exhaust Diffuser 1
19 M5060-19 Stopper 1 49 M5060-49 Inlet Bushing 1
20 M5060-20 Spring Pin (Φ2.5x10) 150 M5060-50 Housing Cover 1
21 M5060-21 Hexagon Nut (M6) 1 M5060-51A Grinding Belt (#100x10) 1
22 M5060-22 Washer (M6) 1 M5060-51B Grinding Belt (#80x10) 1
23A M5060-23A Drive Pulley 1 M5060-51C Grinding Belt (#120x10) 1
24 M5060-24 Housing 1 M5060-51D Grinding Belt (#60x10) (Opt.) 1
25 M5060-25 Ball Bearing (6000ZZ) 1 M5060-51E Grinding Belt (#40) (Opt.) 1
26 M5060-26 Front End Plate 1 54 M5060-54 O-Ring (ID3x1) 1
27 M5060-27 Spacer 1 55 M5060-55 Pully Cover 1
28 M5060-28 Rotor 1 56 M5060-56 Ring 1
29 M5060-29 Parallel Key Both Ends Round 4x4x9.5 157 M5060-57 Hex. Wrench (1.5mm) 1
30 M5060-30 Rotor Blade 5 58 M5060-58 Hex. Wrench (4.0mm) 1
ST-M5060-P-2306F-D5
51