Summer LookOut Duo User manual
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551 4/19
Thank you for purchasing the LookOut™Duo with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.
Install the Nursery Camera
on tabletop
LookOut™Duo comes with 2 camera stands for use on tabletops or dressers.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 ft. from crib.
For tabletop use:
1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.
2. Place camera on a flat surface,
such as a dresser or shelf.
tabletop
wall mount
SETTING UP THE CAMERA & HANDHELD SCREEN
1
Secure the Camera Cord
NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.
6 ft.
Power on the Nursery Camera
& Parent Handheld
1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.
2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.
NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)
STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).
WARNING
Read all warnings prior to using this product.
Charge the Handheld
Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.
TALK
BACK
Congratulations! You are now ready to use your LookOut™
Duo with No-Hole PrestoMount™ Digital Color Video Monitor!
Setting Nursery Temperature
Units (°F or °C)
1. Press the MENU/SELECT button .
2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .
3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.
4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .
Menu screen will return to camera
mode after 8 seconds of inactivity.
For most accurate measurement of room
temperature, MAKE SURE to move the
temperature sensor away from the
nursery camera.
Adjusting the Handheld
Screen Brightness
1. Press the MENU/SELECT button .
2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .
3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.
VIEWING YOUR BABY
3
Screen Icons
GETTING TO KNOW YOUR HANDHELD
2
Nursery Temperature
Display
Talk-back
Zoom
Reception
Current Viewing Camera (1-4)
Battery Life/Plugged In
Function Buttons
Power/Video
Menu/Select
Volume Up
Volume Down
Talk-back
Zoom
Flip out the
kick-stand and place
the monitor on a
stable, level surface.
Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.
1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.
2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.
Zoom In and Out
1. Press the ZOOM button to
zoom in.
2. Press the button again to zoom
out.
Volume
Press the UP/DOWN arrow buttons
to increase and decrease the
volume.
Sound-Activated Lights
The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.
HEARING & SOOTHING YOUR BABY
4
Talk-back to Baby
Reassure and soothe baby with the
sound of your voice and press of a
button.
1. Press and hold the TALK-BACK
button to talk to your baby.
2. Release the button to end
talk-back mode.
with No-Hole PrestoMount™
To remove wall mount:
1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.
Install the Nursery Camera
on wall
NOTE: For best picture focus, place
camera 6 ft. from crib.
For wall mount use:
1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.
2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 24 hours before
putting the camera onto the wall
mount.
3. Slide camera onto mount until it
clicks into place.
4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.
OPTIONAL:
Remove tab from mount and use wall
anchor and screw provided to attach
mount.
6 ft.
Table top use:
Wall mount use:
7hr.
3sec.
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the crib.
This clip will serve as an added measure to help prevent the camera from
falling. Remove and discard the paper backing from the back of the security
clip and press for 30 seconds against wall.
If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand. You can order more security clips or wall mounts through
our Customer Relations.
Left Facing Camera
mount position.
Right Facing Camera
mount Position.
Important Tips/Caution for Wall Mount and Cord Clip Installation:
Failure to follow instructions carefully may cause damage or incorrect
installation
•Wait 7 days after painting before use.
•Do not hang over crib or on wallpaper.
•Use on painted walls or painted/varnished wood.
•Not approved for use on textured walls, wallpaper, brick, fabric,
other rough and non-stick surfaces.
•Use indoors 50 degrees F to 105 degrees F.
•Do not use in humid environments.
•Wipe wall with rubbing alcohol.
•Do not use household cleaner or water.
•Remove liner from wall mount / cord clip.
•Press firmly on wall for 30 seconds.
•Wait 24 hours before adding camera to wall mount.
•To remove wall mount or cord clips, stretch pull tab down slowly
downward against wall at least 15 inches (38 cm) to release.
•Keep other hand on wall mount / cord clip to keep secure while
removing from wall.
•If using camera on a dresser or shelf with the camera stand,
recommended to use a cord clip close to the camera to help
prevent the camera stand from sliding
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
MONITOR OWNER’S GUIDE
36154
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.
• STRANGULATION HAZARD - Children have STRANGLED in
cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.
• When an AC Adapter is plugged into an electrical
outlet, do not touch the exposed end.
• Test monitor before first use, periodically, and when
changing location of the Camera.
• Do not use monitor near water (such as bathtub, sink,
etc.).
• Keep monitor away from heat sources (such as stoves,
radiators, etc.).
• Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
• This product is not a toy.Do not allow children to play
with it.
• This product contains small parts. Adult assembly
required. Exercise care when unpacking and assembling
the product.
Adult assembly required. Keep small
parts away from children when
assembling.
• Use only the original rechargeable battery provided.
Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.
• Do not short-circuit supply terminals.
• Only the recommended battery or equivalent are to be
used, volts and size.
• Remove battery when product is stored for long periods
of time or when battery is exhausted.
• Dispose of exhausted battery properly.
• Keep all batteries away from children.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Summer Infant (USA), Inc. Monitor Warranty Policy
Summer Infant (USA), Inc. will repair or replace (at our option) your unit
free of charge for 12 months from the date of purchase if the unit is
defective in workmanship or materials. To claim your repair/replacement,
the product must be returned to Summer Infant along with a copy of the
original purchase receipt. In the absence of the purchase receipt, the
warranty will be 12 months from the date of manufacture. This warranty
does not apply to normal wear or damage from misuse, abuse, improper
storage and handling, installation, accident, unauthorized repair or
alteration. Please contact our Consumer Relations Team by phone at
401-671-6551 or via e-mail at summerinfant.com/contact for details. For sale
and use in the USA and Canada. The warranty is null and void if used
outside its intended territory.
FCC INFORMATION IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be
retained for future reference.
3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions - All operating and use instructions should be
followed.
5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.
10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIPS & TROUBLESHOOTING
732-2994000-0700
© 2019 Summer Infant (USA), Inc.
Colors and styles may vary.
Please retain information
for future reference.
Made in China.
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895
401-671-6551
To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact
• Camera AC Adapter:...........................................................#29580-05
• Handheld AC Adapter:........................................................#29580-13
• Extra Camera:.......................................................................#36164
• Handheld Screen:................................................................#36134-02
• Wall Mount:...........................................................................#36134-21
• Cord Clips:............................................................................#36134-22
• LookOut™ Tabletop Stand:.................................................#36134-20
• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10
ORDERING REPLACEMENT PARTS
CONTACT US
No picture or sound
• Make sure the camera and handheld monitor unit are paired.
• Make sure the camera and handheld monitor unit are turned on.
• Make sure the AC adapters are plugged in.
• Make sure the outlets are working.
Sound but no picture
• Press the Video On-Off Button once to turn on video mode.
• Make sure nothing is blocking the camera.
• Test reception by moving the handheld unit and/or camera to
different locations.
• Make sure the camera and handheld monitor unit are paired.
Picture but no sound
• Power the handheld completely off, then turn handheld back on.
• Turn up the volume using Volume Control.
Picture not clear
• Wipe camera lens with microfiber or clean, damp cloth.
• Position the handheld unit closer to the camera.
• Move the handheld unit away from other electronic devices, cordless
phones, etc.
• Adjust the brightness using the Brightness Control.
• Test reception by moving the handheld unit and/or camera to different
locations.
• Place camera 6 ft. from crib for optimized focus. Make sure to follow
instructions and warnings for camera placement.
We're here to help!
If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.
Summer Canada, Ltd.
200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484
Adding a Camera
Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.
1. Make sure the power is on for
the camera you want to add.
2. Press the MENU/SELECT button
to enter menu screen.
3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.
4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.
5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.
ADDING AND VIEWING CAMERAS
5
If unsuccessful, repeat the above steps.
Extra Cameras:
To order an additional camera (item #36164), please contact our
Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.
Deleting a Camera
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.
3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.
4. Press the MENU/SELECT button
to delete that camera.
Selecting a Camera to View
1. Press the MENU/SELECT button .
2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.
3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.
4. Press MENU/SELECT button to
confirm selection.
Scanning Cameras
1. Press the MENU/SELECT button .
2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.
3. To stop scanning, press the
MENU/SELECT button .
WARNING
WARNING
WARNING
TIPS & TROUBLESHOOTING (cont.)
Squealing sound coming from speaker on Handheld Unit
• Move the handheld unit and camera further away from each other.
• Turn the volume down using Volume Control.
• Power both the handheld and camera off completely. Remove and
re-insert the handheld battery, then turn both back on.
Handheld is beeping
• If no video, turn on camera.
• If battery is low, charge battery.
After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.
Temperature listed as LL or HH
• Room temperature is outside of the thermometer limits. The thermometer
is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.
Camera isn’t syncing with handheld
• Delete camera and add it back.
16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.
17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
BATTERY:
EXIT MENU
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
SELECT
EXIT MENU
EXIT MENU
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
VIEW CAM
BRIGHTNESS
SCAN
ADD CAM
DELETE CAM
EXIT MENU
TEMP UNITS
Table of contents
Other Summer Baby Monitor manuals
Summer
Summer 2710 User manual
Summer
Summer 28130 Datasheet
Summer
Summer 28680 User manual
Summer
Summer Secure Sleep 02631 User manual
Summer
Summer 28450 User manual
Summer
Summer Best View 02641 User manual
Summer
Summer Baby's Quiet Sounds 02090A User manual
Summer
Summer LIV CAM User manual
Summer
Summer 28630 User manual
Summer
Summer WIDEVIEW User manual
Summer
Summer Ultrasight User manual
Summer
Summer SLEEK & SECURE User manual
Summer
Summer 29040 User manual
Summer
Summer 28980 User manual
Summer
Summer baby wave deluxe User manual
Summer
Summer CLEAR SIGHT 29040 User manual
Summer
Summer Clearsight 29260 User manual
Summer
Summer 28820 User manual
Summer
Summer Sleek & Secure 02290 User manual
Summer
Summer 28660 User manual
