Summit RIDGE 2.0 User manual

2Make sure all components are present.
1 of 4
START HERE
QUICK START GUIDE
Keypad Unit Transceiver Unit 9-V Battery Key Carriage Bolt
( x4 )
Hex Nut
( x4 )
1Carefully unpack box.
What’s what?
All the important
internal components
labeled for you
Transceiver
Shown with cover removed.
Internal wiring not shown for clarity.
Keypad Unit
Back of front panel shown with 9-V battery installed
Internal wiring not shown for clarity.
9-V Battery
Must be installed before use. Connection Terminals
For wiring to compatible
AC/DC power source and
gate operator or door opener
Relay Status LED
Indicates whether relay is
active or inactive
(Relay is active when lit)
Programming Button
For pairing transceiver to keypad
Reset Button
For performing reset procedures
on keypad
Power LED
Indicates whether or not unit has power
Nightlight/Status LEDs
Illuminate keypad and give helpful feedback
Programming LED
Indicates status of pairing process

2 of 4
QSG-S14500-EN Rev. A (1/2017)
QUICK START GUIDE
© 2017 Security Brands, Inc. All rights reserved.
CAUTION!

Transceiver is not weatherproof and must be mounted inside a
weatherproof enclosure. Internal components can be damaged if
exposed to the elements.
Failure to comply will VOID WARRANTY.
5a Connect transceiver
Ridge Transceiver
12–24 VAC/DC
POWER
RELAY A
12–24 VAC/DC
POWER
Gate Operator / Door Opener
POS. (+)
NEG. (–)
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
OR
12–24-VAC/DC
Power Source
(Not Included)
NC
NEG. (–)
POS. (+)
+–
COM
NO
FREE EXIT
COM
5b Connect transceiver
COM
RADIO
Ridge Transceiver
12–24 VAC/DC
POWER
RELAY A
12–24 VAC/DC
POWER
Gate Operator / Door Opener
POS. (+)
NEG. (–)
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
12–24-VAC/DC
Power Source
(Not Included)
NC
NEG. (–)
POS. (+)
+–
COM
NO
FREE EXIT
COM COM
RADIO
Gate Operator Timer-to-Close
OFF
Gate Operator Timer-to-Close
ON
A closing gate can cause injury to
persons or damage to property.
ALWAYS USE SAFETY DEVICES!
CAUTION!

WARNING!
AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH!
ALWAYS CHECK that the GATE PATH IS CLEAR BEFORE OPERATING!
REVERSING or other SAFETY DEVICES SHOULD ALWAYS BE USED!

3Unlock and remove front panel of
keypad unit, then using included
carriage bolts and hex nuts, attach
unit to pedestal as shown.
4Using TEK screws, zip ties, or another
type of fastener (not included),
attach transceiver to inside wall or
another surface of gate operator.

7Add Access Code to Channel A.
(To add multiple codes, enter them all before pressing pound key)
ADelete Code
(To delete multiple codes, enter them all before pressing pound key)
6b Pair keypad with transceiver by
entering sequence below on keypad.
(Make sure 9-V battery is connected to keypad)
BSet Unique Keypad ID
(Allows multiple keypads and transceivers to be used. If Keypad ID is changed,
keypad and transceiver must be paired again.)
3 of 4
QUICK START GUIDE
6c While pairing, keypad will beep and LEDs will flash.
Once pairing is complete, keypad will sound a
“good” tone and transceiver LED will go out.
LED will
go out
9
LED will light
solid red
6a Press and hold Programming button
on transceiver circuit board for
1 second then let go.
8Make sure gate path is clear, then
enter access code on keypad and
confirm gate opens.
(If keypad locks up, repeat Step 6)
1 12 5 5 ? ? ? ?
Unique Keypad ID
(4 digits)
Master Code
(can be changed)
91 12 5 1
Master Code
(can be changed)
Channel
(1 for A, 2 for B)
11 12 5 ? ? ? ?
Access Code
(4 digits)
Master Code
(can be changed)
21 12 5 ? ? ? ?
Code to Be Deleted
(4 digits)
Master Code
(can be changed)
Your system is ready to use.
INSTALLATION COMPLETE!
N
Additional programming commands

CMore programming commands
4 of 4
QUICK START GUIDE
QSG-S14500-EN Rev. A (1/2017)© 2017 Security Brands, Inc. All rights reserved.
NEED HELP Phone: [phone]
Fax: [phone]
Email: [email protected]
31 12 5 ? ? ? ?
New Master Code
(4 digits)
Current Master Code
(if unchanged)
Change Master Code
51 12 5 ? ? ? ?
Latch Code
(4 digits)
Channel
(1 for A, 2 for B)
Master Code
(can be changed)
1
Add Latch Code
1
Add Access Code to Channel B
(To add multiple codes, enter them all before pressing pound key)
81 12 5 ? ? ? ?
One-Time-Use Code
(4 digits)
# of Uses
(1–9)
Master Code
(can be changed)
?
One-Time-Use Code (Channel A ONLY)
01 12 5 1 2 5 1
Master Code AgainMaster Code
(can be changed)
1 12 5
Master Code
(can be changed)
Delete All Codes (Cannot Be Undone)
61 12 5 ? ? ?
Seconds
(000–999)
Channel
(1 for A, 2 for B)
Master Code
(can be changed)
1
Change Relay Output Time
41 12 5
Audible Tone
(On: 1 beep; Off: 2 beeps)
Master Code
(can be changed)
2
41 12 5
Audible Tone
(On: 1 beep; Off: 2 beeps)
Master Code
(can be changed)
2
Three Strikes, You’re Out
Check Status
Turn On or Off
712 5 ? ? ? ?
Access Code
(4 digits)
Master Code
(can be changed)