Sun Microsystems SUN-OCC-SMC576 User manual

All the trademarks mentioned in this manual are registered property of Sun Telecom.
The right to interpret this manual is reserved by Sun Telecom.
English
User’s Manual
SUN-OCC-576SMC
Outdoor Fiber Optic Cross-connect Cabinets

www.suntelecom.cn • [phone] • [e-mail]
NOTICE
Trademarks
All trademarks mentioned in this manual are registered
property of our company.
Explanation
The content of this manual is subject to our explanation.

Fiber Optic Solutions Provider 1/8
www.suntelecom.cn • [phone] • [e-mail]
1 Feature and specification
Feature
Cabinets with SMC material: heat insulation, waterproof and good
corrosion resistance
High performance rubber seals: effective rain and dust proof for outdoor
environment
Modules individually removable: easy to construct and maintain
Reliable cable fixing and grounding protection devices
Safe and reliable fiber optic storage and protection
Specification
Parameters
Specification
Model
SUN-OCC-SMC576
Max. No. of Cores
576
Max. No. of Splitters
20
Cabinet Material
SMC
Adapter Panel
FC square, SC, DLC (SC type), (ST and FC
small D type can be customized)
Insulation Resistance
(MΩ)
1000 @500V (DC)
Withstanding Voltage
(V/min)
3000 (DC), no breakdown, no flashover
Installation Type
Ground
Protection Rating
IP65
Operating
Temperature (°C)
-40~ +60
Dimensions (mm)
1450(H) x 750(W) ×540(D)
Weight (kg)
159

Fiber Optic Solutions Provider 2/8
www.suntelecom.cn • [phone] • [e-mail]
2 The installation of the cabinet
2.1 The installation and debugging of the cement
2.1.1 Prefabricate the cement as picture 1 below.
Sketch of the prefabricated cement
Dimension of the cement(H*L*W): 810mm×680mm×400mm
Leave a 550mm×450mm×400mm hole for the wire to entry in the
foundation center.
2.1.2. Pre-embed ground screws and ensure the center length of the ground
screw to be 612mm ×450mm and at the same time the screw is 50mm above
ground. (The expansion bolt is also available here.)
2.1.3. Put the cabinet on the cement and make sure the fixing hole is aligned
to the ground screw.
2.1.4. In the case of the existing cement, four M17×100 expansion screws is
enough to do the fixing.
2.2 The installation and the debugging of the cabinet base
When adopt matched-installation, the base can be fixed on the cement first
according to the actually situation and then connected to fixing base of the
cabinet.
3 Use and maintenance
3.1 Working principle of the cabinet see picture 2.

Fiber Optic Solutions Provider 3/8
www.suntelecom.cn • [phone] • [e-mail]
Picture 2
3.2 Strip fiber cable
3.2.1 Strip the fiber cable from where is 2800mm away from the end to strip.
3.2.2 Cut crosswise the outer sheath before stripping with the special stripping
knife and carve scratch on the steel strip (but not cut) and then gently bend it
back and forth until it break. Remove the disconnected steel strip together
with the outer sheath to expose the integrated aluminum sheath.
3.2.3 Take two checking rings and one hose clamp, whose diameter is similar
with the diameter of the fiber cable and put it into the fiber cable in turn.
3.2.4 Starting at the end of the integrated aluminum sheath, cut 1800mm of
the PR inner sheath and LAP layer and remove the sheath. Be patient to
avoid damaging the fiber loose tube.
3.2.5 Lengthwise cut 30mm along the sheath direction at the integrated
aluminum sheath breaking point and then crosswise cut 10mm. at this time
you will see the L-shaped incision as picture 4 shows.
3.2.6 Cut the winding wire and wrapping tape, and round up the aramid cord.
Leave 150mm for the wrapping tape and aramid cord.

Fiber Optic Solutions Provider 4/8
www.suntelecom.cn • [phone] • [e-mail]
Picture 3
3.2.7 Clean up the optical fiber loose tube, strength member and wrapping
cord. Please wipe outwards from integrated aluminum sheath breaking point,
opposite direction is prohibited, to avoid the loose tube breaking. It is
forbidden to use gasoline and other flammable solvent scrubbing in case of a
fire.
3.2.8 The fiber loose tube is bent caused by wring. Straighten the tube with
electric hair drier and avoid overheating to prevent the loose tube from
softening deformation.
3.2.9. Crosswise carve a circle scratch on the loose tube surface with the
cutting knife and the carving point is 450mm away from the integrated
aluminum sheath breaking end. Gently break the loose tube in the scratched
point and remove it. Please don’t cut the loose tube in case of the damage of
the optical fiber.
3.2.10. Clean up the filling gel of the optical fiber. Please along the loose
tube-fiber end direction when wipe and the opposite direction is forbidden.
3.2.11. If necessary, you can stick the loose tube and fiber can be sticked
3.3 The fix and grounding of the cable inlet device
3.3.1 Put the cable into the device through the bottom of the cabinet and then
into the cable fixing and grounding protection device
3.3.2 Strip the cable from 100mm ahead from where the hose hoops fixed at
with the special cable stripping knife and protect the fiber with sheath. The
length of stripping should be from 100mm to 1000mm.

Fiber Optic Solutions Provider 5/8
www.suntelecom.cn • [phone] • [e-mail]
3.3.3 Fix the armored fiber cable to the cable fixed board with hose clamp and
fix the strength member to the grounding copper column.
3.3.4 Connect the ground wire is to the cable fixing plate, and then connect it
with room ground.
3.4 The cabinet adopts combinations step rubber bushing for different
diameter cable into the box. The open aperture of the rubber bushings
should be at least 2mm smaller than the diameter of the fiber cable.
3.5 Thread the stripped fiber into the serpentine hose, and fix the serpentine
hose on the binding wire board and then introduce into the splice tray
according to the natural curvature.
3.6 Thread the optical fiber splice protection sleeves into the fiber core, and
then splice the ends of the fiber core with the ends of the pigtail core
and then drive them into the splice tray. (Each splice tray can splice 12
single -core optical fiber.)
3.7 Introduce the spliced pigtail to the patch panel and insert it to
corresponding adapter.
3.8 Fiber-optic lines are connected and scheduled through cross-connection
with the pigtails. The best length of the pigtail is from 1meter to 1.5
meter.
3.9 When does not require scheduling, the trunk cable and drop cable can
be placed directly into the splice tray for protection after being spliced.
4 Notes
4.1 This cabinet is suitable for the connection, distribution and dispatch of
outdoor cable. It is supposed to be fixed on the firm fixing base for easy
installation and dispatch.
4.2 There is an air cleft between the cabinet border and the baseboard to
keep the inside of the cabinet dry. Do not block it during the installation.

Fiber Optic Solutions Provider 6/8
www.suntelecom.cn • [phone] • [e-mail]
4.3 4.3 Keep the excess part of the fiber cable bending naturally and the
bending radius should be 20 times bigger than the diameter of the fiber
cable.
4.4 The opening direction (left or right) of the cabinet is up to the user. As
long as the positioning pin is removed, you can change the opening just
by rotating the door 180 degree.
4.5 The lock hole of the box door is equipped with a stainless steel
protective cover. Close the cover to prevent the hole was blocked after
installation.
4.6 Be careful when operating the optical fiber to avoid piercing the skin and
eyes.
4.7 You are advised not to look directly at the fiber or the end-face of the
fiber connector during the light energy was transmitted optically unless
the safe energy output is guaranteed.
5 Packing, transportation and storage
5.1 Packing
The packing of the device comply with the packing specification with
measurement to proof damp and shock. The package is printed with rain,
moisture, shock and direction signs.
5.2 Transportation
The device is suitable for all kinds of transportation. Keep the temperature at
-25℃~+55℃and relative humidity less than
85％（at +30℃）. When the temperature is above +30 ℃or in rainy
days ,prepare awnings to avoid products directly affected by sunlight or rain
shower. Handling and carrying the products according to the transport
operation mark.
5.3 Storage
Do not put overweight items on the top of the cabinet. The treasury acidic,
alkaline of the air or other harmful gases should comply with environmental
requirements in the warehouse. and keep the indoor temperature between
-25 ℃~ +55 ℃and the relative humidity less than 85% (+30 ℃pm).

Fiber Optic Solutions Provider 7/8
www.suntelecom.cn • [phone] • [e-mail]
An important message from Sun Telecom
We guarantee that any information you supply will remain confidential.
By returning this card, you will automatically be notified about updates,
modifications, and recalibration.
Warranty Registration Card
Serial Number:
Model Number:
Date of Purchase:
Company Name:
CompanyAddress:
TEL: FAX:
E-mail:
Note: Please fax this note within one month from the date of receiving
units.
YOUR OPINION
Do you have any comments on the quality of this product or the service from
us?

Fiber Optic Solutions Provider 8/8
www.suntelecom.cn • [phone] • [e-mail]
SHANGHAI SUN TELECOMMUNICATION CO., LTD.
Building No.145, Lane 666 Xianing Road,
Jinshan Industrial Park, Shanghai 201506 China
Tel: [phone] Fax: [phone] - 401
E-mail: [e-mail]
http: //www.suntelecom.cn/