Sunbeam PBT7000SS User manual

BLENDER
TM
User Guide
PBT7000SS

1
Sunbeam’s Safety Precautions 1
Welcome 2
Features of your Sunbeam ActiveSenseTM Blender 3
Blend-N-Go™ Bottle Accessory 4
Before Using your ActiveSenseTM Blender 5
Using your ActiveSenseTM Blender 6
Blade and Jug Assembly 7
Using Your Blend-N-Go™ Bottle 8
Care and Cleaning 9
Handing Blending Tips 10
Frequently Asked Questions 11
Recipes 12
Contents
SAFETY PRECAUTIONS FOR YOUR SUNBEAM
ACTIVESENSE™ BLENDER
• Ensure fingers are kept well away from the
blades when in use.
• Do not blend warm/hot ingredients. Always
cool ingredients to room temperature before
processing.
• Hot/warm ingredients can eject out of the jug
when a sudden steaming is caused.
• Do not immerse in water.
• Always operate on a flat surface.
• Take care when removing the Jug from the
base or emptying the Jug as blades are
extremely sharp.
• Switch off the appliance and disconnect
from supply before changing accessories or
approaching parts that move in use.
• Unwind cord fully before operating.
Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug when
the appliance is not in use and before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service
person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked on the
appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while in
use.
• Do not use an appliance for any purpose
other than its intended use. Misuse will cause
potential injury.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage
is suspected, return the appliance to the
nearest Sunbeam Appointed Service Centre for
examination, repair or adjustment.
• For additional protection, appliance should
be supplied through a residual current device
(RCD) having a rated residual operating current
not exceeding 30 mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water or any
other liquid unless recommended.
• Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
Sunbeam is very safety conscious when designing and manufacturing consumer products,
but it is essential that the product user also exercise care when using an electrical appliance.
Listed below are precautions which are essential for the safe use of an electrical appliance:
Sunbeam’s Safety Precautions
If you have any concerns regarding the performance and use of your appliance,
please visit the Sunbeam Website or contact Sunbeam Consumer Care - details are
on the back page. Ensure the above safety precautions are understood.
Important Instructions - Retain For Future Use

2 3
Congratulations on your new Sunbeam blender with ActiveSense Technology™ Your blender will
allow you to create delicious smoothies, milkshakes, salsas and much more every day!
Your product includes the following features and benefits:
• ActiveSense Technology™ takes the guesswork out of blending. When using the Food Mode
settings, the blender senses what is in the jug and automatically adjusts its blending speed,
blade direction and run time to deliver a blended meal to the consistency selected.
• The ability to know when there is not enough liquid in the Jug to properly blend. ActiveSense
Technology™ will stop the blending process and notify you to add more liquid when this
happens.
• A user-friendly control panel which gives you the flexibility of using Manual Controls or
selecting from a variety of Food Modes. With Food Mode, take it a step further by choosing the
thickness of your drink too.
• An advanced 6-Point Extra-Wide Blade System with patented Reversing Blade Technology™,
which cycles forward and backward at varying speeds to deliver optimal results for your
blending needs.
• A Blend-N-Go™ bottle and spill-proof drinking lid so you can conveniently take drinks on the
go!
Welcome Features Of Your Sunbeam ActiveSense™ Blender
1. Filler Cap
2. Jug lid
3. Break Resistant, BPA-Free Tritan™ Plastic Jug
4. Sealing Ring
5. 6-Point Blade
WARNING: The blade is very sharp, handle carefully.
6. Threaded Jug Bottom
7. Motor Base
8. Control Panel
a. Power Button
b. Food Mode selection:
Milkshake
Juice
Smoothie
Salsa
Frozen Drink
c. Thickness selection:
For Beverages: Thick or Thin
For Foods: Chunky or Smooth
d. Manual Controls
High
Med
Low
e. Pulse Button
f. Start/Pause Button
FOOD
MODE HIGH
MED
LOW
THICKNESS
PULSE
1
2
3
4
5
6
7
8
FOOD
MODE HIGH
MED
LOW
THICKNESS
PULSE
b
d
ae
f
c

4 5
FOOD
MODE HIGH
MED
LOW
THICKNESS
PULSE
2
1
3
4
5
6
1. Cup Lid
2. Break Resistant, BPA-Free Tritan™
Plastic Cup
3. Sealing Ring
4. 6-Point Blade
WARNING: The blade is very
sharp, handle carefully.
5. Threaded Jug Bottom
6. Motor Base
Blend-N-Go™ Bottle Accessory Before Using Your ActiveSense™ Blender
Step 1. Remove Packaging
Ensure all packaging has been removed
carefully.
Important: : Always ensure your blender is
unplugged from the power outlet before fitting
or removing the Blade Assembly. Always
handle the Blade Assembly with caution, as the
blades are extremely sharp.
Note: When removing the Blade Assembly from
the Jug you may need to slightly tilt the blade
assembly so that it slides out easily.
Step 2. Wash and Dry Parts
Note: Before using your ActiveSense™ Blender,
we recommend removing the 6-Point Blade
Assembly for thorough cleaning. See page 7 for
more details.
1. Remove carefully the Blade Assembly
from the Tritan™ Jug by holding the Jug
upright and turning the Blade Assembly
clockwise.
2. Wash the parts listed below in warm
soapy water:
- Blade Assembly
- 1.7L blending Jug
- Jug Lid
- 750mL Blend-N-Go™ Bottle
- Cup Lid
3. Rinse and allow thorough air drying.
Step 3. Re-assemble the 6-Point Blade
Assembly in the Tritan™ Jug
Place carefully the Blade Assembly in the
Tritan™ Jug. Ensure that the Blade Assembly is
firmly in place by turning it anti-clockwise from
bottom of the Jug. The blender Jug will leak if
the 6-Point Blade Assembly is not assembled
correctly.
Step 4. Secure the Jug Lid and Filler Cap
Place the Jug Lid firmly onto the blending Jug.
Ensure the Filler Cap is tightly locked to avoid
movement during blending.

6 7
Using Your ActiveSense™ Blender Blade and Jug Assembly
Note: Before you use the blender for the first
time, separate all parts and clean them. Refer
to page 9 for Care and Cleaning instructions.
Food Mode Selection
1. Press the Power button to turn the
blender on. The Start/Pause button will
blink, indicating the product is active and
ready to use. The light will stay on when
the motor is running.
2. Press the Food Mode button, then use
the up and down arrow buttons to make a
selection:
- Milkshake
- Juice
- Smoothie
- Salsa
- Frozen Drink
3. (Optional) Press the Thickness button to
select a thickness option for the meal:
- For Beverages: Thick or Thin
- For Foods: Chunky or Smooth
4. When ready to begin, press the Start/
Pause button. The blender will notify
about the progress and will stop
automatically when blending is complete.
Press the Power button to cancel the
program at any time.
5. Press the Power button to turn
the blender off. The blender is
pre-programmed to turn off automatically
if not used for several minutes. All lights
will turn off to indicate this.
Using the Manual Controls
1. Press the Power button to turn the
blender on. The Start/Pause button will
blink, indicating the product is active and
ready to use. The light will stay on when
the motor is running.
2. Press a Manual Control button, choose
from Low, Med or High. When ready to
start press the Start/Pause button.
3. Press the Power button to turn
the blender off. The blender is
pre-programmed to turn off automatically
if not used for several minutes. All lights
will turn off to indicate this.
Add Liquid Function
• ActiveSense TechnologyTM has the ability
to sense when there is not enough liquid
in the Jug to properly blend.
• If the blender senses this issue, it will
stop blending and display a notification.
• Add more liquid and press the Start/
Pause button to resume blending.
IMPORTANT:
This blender has an interlock system which
prevents the Motor or Control Panel from
starting if the Blender Jug is not properly
placed on the Motor Base.
If the Jug is removed during operation the
blender will stop and the Power and Start/
Pause buttons will flash continuously.
Caution: Blades are sharp. Handle with care.
1. Place the Blade Assembly into the
Threaded Jug Bottom.
2. Place the Sealing Ring over the Blade
Assembly. Carefully press and tuck the
Sealing Ring into the locking groove.
3. Ensure the Sealing Ring is fully and evenly
tucked in place and holding the Blade
Assembly to the Threaded Jug Bottom.
Incorrect Correct
4. Install the Blade Assembly into the Jug.
Turn clockwise to tighten. Ensure the
Blade Assembly is tightened to the Jug
before using.
Note: The Filler Cap can be used as a tool
to tighten or remove the Threaded Jug
Bottom.
5. Place ingredients into the Jug. Secure the
Lid and Filler Cap then slide the Jug onto
the Motor Base.
Filler Cap
Threaded Jar
Bottom

8 9
Using Your Blend-N-Go™ Bottle
Note: Never blend hot liquids in the
Blend-N-Go™ Bottle.
1. Place the blade in the threaded Jug
bottom.
2. Place the Sealing Ring over the Blade
Assembly. Carefully press and tuck the
Sealing Ring into the locking groove. Refer
to page 7 for detailed instructions on
blade assembly.
3. Place all ingredients into the Bottle,
then tightly screw the Blade Assembly
clockwise into the Bottle.
4. Place the Bottle onto the Motor Base,
push down and turn anti-clockwise to
lock. The Bottle should be sitting evenly
on the 4 grooves of the Motor Base.
5. Select the Food Mode and Thickness or
Manual Control (Low, Med, High) using
the Control Panel buttons. Press Start/
Pause Button to begin blending.
Note: The Food Mode Salsa option is not
available with the Blend-N-Go™ Bottle
accessory.
6. Press the Start/Pause button to stop
blending and the Power button to turn
the blender off. Remove the Bottle from
the Motor Base by applying downward
pressure and turning clockwise before
lifting up.
FOOD
MODE HIGH
MED
FOOD
MODE HIGH
MED
Placing The Cup Assembly Removing The Cup Assembly
Care And Cleaning
Cleaning
Caution: Blades are sharp. Handle
carefully.
• Empty the blending Jug. If necessary, use a
rubber spatula to scrape foods away from
the sides of the Jug.
• CAREFULLY remove the Blade Assembly
from the blending Jug by turning the Blade
Assembly counter-clockwise.
• All parts (except for the Motor Base)
are dishwasher safe. Use the top rack
of the dishwasher for the Filler Cap, Jar
Lid, Sealing Ring, Blade Assembly and
Threaded Jar Bottom. Place the blending
Jug into the bottom basket of dishwasher.
• The blending Jug, Jug Lid, Filler Cap,
Seal Selector Top, Cup Lid, Cup and Blade
Assembly can also be hand washed with
warm, soapy water. Rinse well and dry.
Note: It is recommended to hand wash the
Blade Assembly for longer usage.
• Check the parts as you put them back
together.
• Wipe the Motor Base with a soft, damp cloth
to clean. Never submerge the Motor Base in
a liquid.
Tip: Run the blender with soapy water for
20-30 seconds on Manual Mode of Low
or Med for cleaning without disassembly.
Follow with a clean water rinse.
Storing
• Reassemble the blender for storage. Leave
the Jug Lid open so no odors are retained.
Caution: Never put the blending Jug, or
any other parts, in a microwave oven.

10 11
Handy Blending Tips
Blending Tips
• Do not operate for more than 10 minutes at
a time.
• Repeated use of the blender in a short
amount of time may result in error. Open
the blending Jug and check the contents.
Wait 30 seconds or unplug then plug in the
unit, then blend.
• Jug should be at least 25% full at all times
for optimal performance.
• Use High speeds as much as possible for
whole food juices, shakes, frozen mixtures,
making purées and nut butters. High speed
provides the best quality of refinement,
breaking down ice, frozen fruit, whole
fruits or vegetables to a smooth lump-free
consistency.
• Use only the amount of food suggested in
the recipes. If you want greater amounts,
prepare in batches. Using larger amounts
may overload and strain the motor.
• Use the PULSE button when mixture is
too thick or coarse to circulate within the
blender Jug.
• If on High speed the food is not circulating,
try using a spatula. If this is also not
working, try using a slower speed. Once
the food begins to circulate again, you can
switch back to a High speed.
• Due to the power of the machine, it is
normal for it to be fairly loud during
operation. Through the blending cycle, the
noises may change, but there is no need to
be concerned.
• Ice Crushing: For optimal ice crushing,
fill the Jug with preferred amount of ice.
Then fill with water just above where the
ice stops. Use the speed dial to blend on
High for a few seconds. Then drain out the
excess water and you are left with a Jug
filled with great consistent ice!
Add Ingredients While Blending
To add ingredients while blending,
remove the Filler Cap by turning it to the
Remove Cap position and lifting up. Add
in ingredients as desired, then put the
Filler Cap back into the Jug Lid and turn
it to the lock position.
Important: DO NOT BLEND HOT
LIQUIDS.
Frequently Asked Questions
Why doesn’t the blender turn on?
• Make sure the Motor Base is plugged into
an active power receptacle.
• Verify the blinking blue light is active after
pushing the Power button.
• The Jug may not properly be placed into
the motor unit. When placed correctly
the Jug type will display on the screen. If
not displayed, ensure the jug is secured
properly to make contact with the sensor.
Why did the blender’s timer reset?
• Check that the Sealing Ring is correctly
assembled in between the Blade and the
Jug.
Why did my blender stop blending?
• The blender is programmed to run a
maximum of seven continuous minutes
before stopping. If you need to blend
longer than seven minutes, wait 30
seconds before blending again.
• There may not be enough liquid in the
Jug to properly blend. If the Blender
senses this issue it will stop blending and
display a notifiction.
The Power and Start/Pause lights are
flashing
• The jug has been removed during
blending operation. Replace the jug and
restart the blending program.

12 13
Recipes
BARBADOS ICED TEA
Serves 2
2 bags of peppermint tea steeped in 1 cup
hot water and 2 teaspoons sugar, chilled
2 cups ice
4 mint leaves
¼ teaspoon ginger powder
Honey for drizzling
1. Place all ingredients into the blender
Jug.
2. Select the FROZEN program and
START.
3. Pour into a high ball glass and garnish
with a sprig of mint.
TRADITIONAL MILKSHAKE
Serves: 3-4.
Makes approximately 1 litre
500ml (2 cups) milk
4 scoops (180g) vanilla ice cream
2 teaspoons vanilla extract
1. Place all ingredients into the blender
Jug.
2. Select the MILKSHAKE and THICK
programs and START. Serve.
TIM TAM SMOOTHIE
Serves: 2
5 Arnott’s Original Tim Tams
4 scoops (180g) vanilla ice cream
400ml milk
1 Arnott’s Original Tim Tam, extra,
crumbled to garnish
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THICK
programs and START. Serve.
3. Garnish with the extra Tim Tam.
Watermelon and Mint Frappe
Serves: 2
6 ice cubes
⅓ cup fresh mint leaves
500g watermelon pieces
Extra mint leaves, to garnish
1. Place all ingredients into the blender
Jug.
2. Select the FROZEN and THIN programs
and START.
3. Pour into serving glasses and garnish
with extra mint to serve.
Tip: Serve immediately, as the mint will
cause the Frappe to go brown on
standing
COCONUT DREAM
Serves: 2
500ml (2 cups) apple juice
125ml (½ cup) light coconut milk
250g frozen strawberries
1 scoop (45g) vanilla ice cream
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THIN
programs and START. Serve.
3. Garnish glass with a strawberry if
desired.
Recipes
BANANA AND BERRY BREAKFAST
SMOOTHIE
Serves 2
2 cups milk
1 banana
¾ cup frozen mixed berries
½ cup rolled oats
1 tablespoon chia seeds
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THICK
programs and START. Serve.
FROZEN BERRY SMOOTHIE
Serves 2
2 cups almond milk
1 cup fresh blueberries
1 cup frozen raspberries
⅓ cup fresh raspberries
1. Place all ingredients into the blender
Jug.
2. Select the FROZEN and THICK
programs and START. Serve.
STRAWBERRY MANGO SMOOTHIE
Serves 2
1¼ cups apple juice
1 cup low-fat plain yogurt
1 cup fresh strawberries
1 cup frozen mango
1 cup fresh mango
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THIN
programs and START. Serve.
FRUIT BASED GREEN SMOOTHIE
Serves 2
1 green apple, chopped
1 pear, chopped
1 cup baby spinach
1 kiwi fruit, halved
1¾ cups coconut water
1. Place all ingredients into the blender
Jug.
2. Select HIGH speed and START. Blend
for one minute. Serve.
VEGETABLE BASED GREEN SMOOTHIE
Serves 2
½ cup chopped carrot
¼ avocado
½ cup frozen banana
2 stalks kale
1½ cups orange juice
1. Place all ingredients into the blender
Jug.
2. Select HIGH speed and START. Blend
for one minute. Serve.
VIRGIN PINA COLADA
Serves 2
1½ cups frozen pineapple chunks
¼ cup ice
1 cup unsweetened pineapple juice
1 cup coconut milk
Fresh pineapple wedges and Maraschino
cherry, to garnish
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THICK
programs and START. Serve.

14 15
Recipes
BERRY JUICE
Serves 4
2 cups fresh strawberries
1 cup fresh raspberries
1½ tablespoons caster sugar (optional)
1. Place all ingredients into the blender
Jug.
2. Select the JUICE program and THICK.
Press START.
3. Once the cycle has finished, add 2 cups
of chilled water to the jug.
4. Select the JUICE and THIN programs.
Press START. Serve.
Tip: You can use any soft fruit such as
mango, kiwi, banana, avocado, peach,
apricot or watermelon to make a
delicious juice.
TOMATO SALSA
Makes 2 cups
½ red onion, peeled
1 large clove of garlic
1 fresh jalapeño or green chilli, seeds
removed
2 ripe tomatoes, quartered
¼ bunch of fresh coriander
1 tablespoon of Balsamic vinegar
2 tablespoon extra-virgin olive oil
Salt and pepper to taste
1. Place the onion, garlic, chilli, tomatoes
and coriander into the blender Jug in
the order listed.
2. Select the SALSA and CHUNKY
programs and START.
3. Remove ingredients from blender jug to
a serving bowl.
4. Dress with combined balsamic and
olive oil seasoned with salt and pepper.
Recipes
MIXED BERRY FRAPPE
Serves: 2
500ml (2 cups) orange juice
300g frozen mixed berries
1 tablespoon caster sugar
1. Place all ingredients into the blender
Jug.
2. Select the FROZEN and THIN programs
and START. Serve.
COFFEE AND BANANA THICKSHAKE
Serves: 2
1 ripe banana, peeled, chopped
30ml espresso, cold
250ml (1 cup) milk
2 scoops (90g) vanilla ice cream
4 ice cubes
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THICK
programs and START. Serve.
Tip: If you don’t have access to a coffee
machine, use 2 teaspoons instant
coffee dissolved in 1½ tablespoons
boiling water. Refrigerate until cold.
MANGO LASSI
Serves: 4
450g mango pieces
1 cup vanilla yoghurt
6 ice cubes
325ml milk
Chopped pistachios and ground cardamom,
to garnish
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THICK
programs and START. Serve.
3. Garnish with pistachios and dust with
ground cardamom.
ICED COFFEE
Serves: 3
60ml espresso, cold
500ml (2 cups) milk
2 scoops (90g) vanilla ice cream
4 ice cubes
Whipped cream and cocoa powder, to serve
1. Place all ingredients into the blender
Jug.
2. Select the SMOOTHIE and THICK
programs and START. Remove the lid
and pour into serving glasses.
3. Top with whipped cream and dust with
cocoa powder.
Tip: If you don’t have access to a coffee
machine, use 1 tablespoon instant
coffee dissolved in ¼ cup boiling water.
Refrigerate until cold.

16 17
MADE IN CHINA TO
SUNBEAM’S
SPECIFICATION
AUTHORITIES
ELECTRICAL REGULATORY
APPROPRIATE
APPROVED BY
Warranty
Level 6, Building 5,
Central Park,
660–670 Great South Road
Greenlane, Auckland
New Zealand
Should you experience
any difficulties with
your product during the
warranty period,
please contact
Sunbeam Customer Care:
:
The Sunbeam ActiveSense
TM
Blender
5 Year Motor Guarantee
Sunbeam has built its reputation on
manufacturing quality electrical appliances.
Our High Performance Blender is constructed
from the highest quality materials. So much
so, we guarantee our Blender motor for
five (5) years against faulty materials or
manufacture. This guarantee is just another
expression of our confidence in the way we
make appliances at Sunbeam. In order to be
eligible for this guarantee, you must retain
your receipt as proof of purchase.
Your High Performance Blender is covered
for the first year against faulty material or
manufacture by the Sunbeam 12 Month
Replacement Guarantee. Should you
experience any difficulties with your appliance
within this 12 Month period, please phone
our customer service line for advice on 1300
881 861 in Australia, or 0800 786 232 in New
Zealand. The Sunbeam (5) five year motor
guarantee begins from date of purchase and
extends for four years beyond the 12 Month
Replacement Guarantee. It covers only the
motor, guaranteeing it against faulty materials
or manufacture. It does not cover damage
caused by accident, misuse or being used in a
manner not in accordance with the Instruction
Book. Similarly, this motor guarantee does
not cover freight or any other costs incurred in
making a claim.
If a fault should develop with the motor
after the period covered by the 12 Month
Replacement Guarantee, please call Sunbeam
Customer Service on the number listed below
or send a written claim to Sunbeam at the
address listed below. On receipt of your claim,
Sunbeam will advise you on how to obtain a
replacement motor if your motor is defective.
Alternatively, you can return the Sunbeam
High Performance Blender to any of
Sunbeam’s authorised service centres,
together with your receipt. The service centre
will examine the motor and if it is faulty or
defective, the motor will be replaced free of
charge.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
1300 881 861
www.sunbeam.com.au
Suite 1, Level 1, 13 Lord Street
Botany NSW 2019 Australia
New Zealand
0800 786 232 26
www.sunbeam.co.nz
Level 6, Building 5, Central Park
660-670 Great South Road
Greenlane, Auckland
The benefits given to you by this guarantee are
in addition to your other rights and remedies
under any laws which relate to the appliance.
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act. In Australia you are entitled
to a replacement or refund for a major
failure and for compensation for any other
reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
IMPORTANT NOTE
Sunbeam agrees to replace the motor in
the event of the motor developing a fault
or defect, within the four years after the 12
Month Replacement Guarantee. As your
High Performance Blender needs to be
assessed at a Sunbeam authorised service
centre, it will not be accepted through
retail stores. If using the Sunbeam High
Performance Blender for commercial
use this motor guarantee is limited to 12
months from the date of purchase.

Newell Australia Pty Ltd | ABN 68 075 071 233
Due to continued product improvements,
product illustrations and photographs in this User Guide
may differ slightly from the actual product.
Printed in China
MADE IN CHINA TO
SUNBEAM’S
SPECIFICATION
AUTHORITIES
ELECTRICAL REGULATORY
APPROPRIATE
APPROVED BY
Need help with your appliance?
Contact our Customer Care Team or
visit our website for information and tips
on getting the most from your appliance.
AUSTRALIA
Visit:
Phone:
Mail:
NEW ZEALAND
Visit:
Phone:
Mail:
www.sunbeam.com.au
1300 881 861
Suite 1, Level 1, 13 Lord Street,
Botany NSW 2019
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5, Central Park,
660–670 Great South Road,
Greenlane, Auckland
PBT7000SS_20EM2 (ANZ)
GCDS-SUN-SL
PN: 3857