Suncorp S0380-0000 User manual

SUNCOR STAINLESS, INC. ■ Rivet Nut Installation Tool (S0380-0000) Instructions ■ www.suncorstainless.com ■ August, 2016
©2016 Suncor Stainless, Inc.
Rivet Nut Installation Tool (S0380-0000) Instructions
Rivet Nut Installation Tool Kit Components
• Rivet Nut Installation Tool
• Wrench
• Mandrel – 1/4”-28 RH
• Mandrel – 1/4”-28 LH
• Mandrel – 3/16” 10-24 RH
• Mandrel – 1/4”-20 RH
• Mandrel – 5/16”-18 RH
• Mandrel – 3/8”-16 RH
• Mandrel – 1/4”-20 LH
• Mandrel – M3 x .5
• Mandrel – M4 x .7
• Mandrel – M5 x .8
• Mandrel – M6 x 1.0
• Mandrel – M8 x 1.25
• Mandrel – M10 x 1.5
• Mandrel – M12 x 1.75
Rivet Nut Installation Tool Features
1. Installation Knob
2. Mandrel Stem
3. Outer & Inner
Sheath
4. Locking Nut
5. Scale Identification
6. Mandrel Nozzle
SUNCOR STAINLESS, INC. Contact Information
Customer Service
[phone]
[phone]
Facsimile
[phone]
Web Address
www.suncorstainless.com
Mailing Address
Suncor Stainless, Inc.
70 Armstrong Rd.
Plymouth, MA 02360
Table of Contents
Rivet Nut Installation Tool Kit Components 1
Rivet Nut Installation Tool Features 1
Installation Steps 2
Changing the Mandrel 2
Manual Release of the Rivet Nut Installation Tool 2
Figure A. Open the handles to thread the rivet nut onto the mandrel
stem.
Figure B. Rotating the outer sheath outward or inward will cause the
working stroke to become longer or shorter respectively.

SUNCOR STAINLESS, INC. ■ Rivet Nut Installation Tool (S0380-0000) Instructions ■ www.suncorstainless.com ■ August, 2016
©2016 Suncor Stainless, Inc.
Installation Steps
This rivet nut installation tool features a scale identification so the
working stroke can easily be known.
Open the handles to thread the rivet nut onto the mandrel stem
(Figure A). By rotating the outer sheath outwards, the working stroke
will become longer. Rotating the outer sheath inwards will cause the
working stroke to become shorter (Figure B). Once the appropriate
working stroke has been established, tighten the locking nut. Using
the wrench (included), tighten the mandrel nozzle (Figure C).
With the rivet nut fully threaded on the mandrel stem, put the rivet nut
into the hole and close the handles to rivet (Figure D).
NOTE: FOR OPTIMAL RESULTS, MAKE SURE THE RIVET
NUT IS FULLY INSERTED AGAINST THE SHOULDER.
Rotate the installation knob counterclockwise to release the rivet nut
installation tool after riveting (Figure E).
NOTE: FOR LEFT HAND THREAD RIVET NUTS, RELEASE
THE RIVET NUT INSTALLATION TOOL BY TURING THE
INSTALLATION KNOB CLOCKWISE.
Changing Mandrels
Use the supplied wrench to remove the mandrel nozzle (Figure C).
Push the inner sheath back and hold it down. Rotate the mandrel to
remove it (Figure F).
To attach a mandrel, push the inner sheath back and screw in the
mandrel. Thread on and tighten the mandrel nozzle (Figure G)
.
Release the inner sheath.
Manual Release of the Rivet Nut Installation Tool
During the riveting process, if the rivet nut installation tool cannot be
removed, do not try to remove it forcefully. Insert an Allen wrench
(6mm) into the hole on the shaft of the mandrel and rotate to remove
the rivet nut installation tool (Figure H).
Figure H. Insert an Allen wrench into the hole on the shaft of the mandrel and rotate
to release the rivet nut installation tool.
Figure C. Use the supplied wrench to tighten or remove the mandrel
nozzle.
Figure D. (Left) Put the rivet nut into the hole and close the handles to
rivet.
Figure E. (Right) Rotate the installation knob to exit the rivet nut
installation too.
Figure F. To release mandrel, push the inner sheath back and unscrew
the mandrel.
Figure G. Push the inner sheath back and screw in the mandrel.
Thread on and tighten the mandrel nozzle.