Sunny Health & Fitness SF-B0717 User manual
ELECTRIC SURFACE CYCLE 90
SF-B0717
USER MANUAL
IMPORTANT! Read all instructions carefully before using this product. Retain owner’s
manual for future reference. For customer service, please contact:
1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is assembled,
maintained and used properly. It is your responsibility to ensure that all users of the equipment
are informed of all warnings and precautions.
1. Before starting any exercise program you should consult your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk, or
prevent you from using the equipment properly. Your physician’s advice is essential if you
are taking medication that affects your heart rate, blood pressure or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
Stop exercising if you experience any of the following symptoms: pain, tightness in your
chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness or feelings of
nausea. If you do experience any of these conditions, you should consult your physician
before continuing with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use
only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or
carpet. To ensure safety, the equipment should have at least 2 feet (60 CM) of free space
all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The
safety of the equipment can only be maintained if it is regularly examined for damage
and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while
assembling or checking the equipment, or if you hear any unusual noises coming from the
equipment during exercise, discontinue use of the equipment immediately and do not use
until the problem has been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment
9. The maximum weight capacity of this unit is 220 pounds (100 KGS).
10. The equipment is not suitable for therapeutic use.
11. Use caution when lifting and moving the equipment. Always use proper lifting technique
and seek assistance if necessary.
12. Your product is intended for use in cool, dry conditions. You should avoid storage in
extreme cold, hot or damp areas as this may lead to corrosion and other related problems.
13. This equipment is designed for indoor and home use only! It is not intended for commercial
use!
WARNING: This product can expose you to one or more chemicals known to the
State of California to cause cancer and birth defects or reproductive harm. For more
information go to www.P65Warnings.ca.gov.
2
EXPLODED DRAWING
HARDWARE PACKAGE
#5 M8 4pcs
#5 M8 4pcs
#A Spanner 1pc
#B Wrench 1pc
#C Wrench 1pc
3
PARTS LIST
NO. Description Spec. QTY
1 Main Frame 1
2 Front Stabilizer 1
3 Rear Stabilizer 1
4 Cap 4
5 Screw M8 4
6 Crank Cap 2
7 Screw M8 2
8L Crank-L 1
8R Crank-R 1
9 Screw M6 6
10 Rubber Plate 2
11 Motor 1
12 Nut 2
13L Pedal-L 1
13R Pedal-R 1
14 Cover-R 1
15 Screw M4 8
16 Magnet 1
17 Plastic Magnet Seat 1
18 Washer 1
19 Screw M3 7
20 Screw M3 1
21 Remote Control Rear Cover 1
22 Screw M2 2
23 Remote Control 1
24 Remote Control Front Cover 1
25 Label 1
26 Remote Control Cable 1
27 Power Cable 1
28 Cover-L 1
29 Control Panel 1
30L Pedal Straps-L 1
30R Pedal Straps-R 1
A Spanner 1
B Wrench 1
C Wrench 1
ASSEMBLY INSTRUCTIONS
STEP 1:
Attach the Front Stabilizer (No. 2) to the Main Frame
(No. 1) using 2 Bolts (No. 5) and secure with Spanner
(A).
Attach the Rear Stabilizer (No. 3) to the Main Frame
(No. 1) using 2 Bolts (No. 5) and secure with Spanner
(A).
#5 M8 2pcs
#A 1pc
5
2
1
#5 M8 2pcs
#A 1pc
5
3
1
4
5
STEP 2:
Connect the Left Pedal (No. 13L) and Right Pedal (No.
13R) onto the Left Crank (No. 8L) and Right Crank (No.
8R).
NOTE: The Left Pedal (No. 13L) and Right Pedal (No.
13R) are marked L for Left Pedal (No. 13L) and R for
Right Pedal (No. 13R). Remove the 2 Nuts (No. 12)
located on the Pedals.
Left Pedal (No. 13L): Align Left Pedal (No. 13L) with the
Left Crank (No. 8L) at 90 degrees. Insert the pedal into
the crank arm; turn the pedal counter-clockwise as tightly
as you can with your hand. Once screwed in place, use
Wrench to hold the bolt of the pedal then screw 1 Left
Nut (No. 12) clockwise into thread end of the Left Pedal
(No. 13L). Secure with Wrench.
Right Pedal (No. 13R): Align the Right Pedal (No. 13R)
with the Right Crank (No. 8R) at 90 degrees. Insert the
pedal into the crank arm; turn the pedal clockwise as
tightly as you can with your hand. Once screwed in place,
use Wrench to hold the bolt of the pedal then screw 1
Right Nut (
No.12R
)counter-clockwise into thread end of
the Right Pedal (No. 13R). Secure with Wrench.
STEP 3:
Attach the Pedal Straps (No. 30) to the Left Pedal (No.
13L) and Right Pedal (No. 13R).
12L
13L
13R 13L
12R
8R
13R
The assembly is now complete!
7
SAFETY NOTES
ELECTRICAL INFORMATION
Rated Voltage: 110V
Do not stand on cycle. Only use while seated in a chair.
If cycle is tilted over 45 degrees, it will auto stop.
If cycle detects problems during exercise, it will auto stop within 10
seconds.
REMOTE CONTROL FUNCTION KEYS
START/STOP
Starts and stop machine
MODE
Changes display between RPM-TIME-ODO
TIME
Changes the timer in 5 minute intervals
DIRECTION
Changes the direction forward or backward
RPM + -
Increases or decreases RPM in intervals of 5
1. Plug in the power. Turn on the power switch. Cycle beeps and display
shows “-.-.-.-“. It is in standby mode.
2. Press the START/STOP button on the remote control to start the cycle.
Cycle automatically starts on a 5 minute timer. Timer can be set to 5, 10, 15, 20, 25, 30 minutes.
Press Time to set the timer. When timer reaches 0, cycle will auto stop.
Press + - to increase or decrease the RPM in increments of 5. Initial RPM is 30. Maximum RPM
is 90.
Press DIRECTION to change the direction forward or backward.
Press MODE to switch the function displayed from RPM to TIME to ODO.
3. Press the START/STOP button to stop the cycle.
NOTE:
After it stops, cycle keeps the last settings. Use the remote control to change the settings.
MODE, TIME, DIRECTION, RPM + - buttons only work when the cycle is pedaling. The buttons do
not work when it is in standby mode.
Version 1.2
OPERATING INSTRUCTIONS
ELECTRICAL INFORMATION
Rated Voltage: 110V
Power switch
Table of contents
