SUNON DAM6026 User manual

Assembly Manual
OFFICE DESK
Please read this manual carefully before any operation
and keep it properly for future use.
Customer Service：[email protected]
DAM6026

M6*45(*34+1) M6*30(*33+1) M6*15(*6+1) M6*10(*8+1)
M4*12(*2+1) M5*15(*2+1) ST3*15(*2+1)
15*40L(*6+1)
M4*18(*2+1)
8*40(*2+1) 5*150
11
Warnings
IMPORTANT!
After 180° right turn, if there is a gap
between the boards, please check
whether the cam lock pin is
tightened enough.
1/2 RIGHT
TURN FOR
LOCKING
FUNCTION OF KLIX CAM
MAKE SURE THE ARROW OVER AGAINST THE
TOPSIDE OF CAM LOCK PIN BEFORE
INSERTING INTO THE PANEL'S HOLE
Components ListComponents List
ABC
GF
E
D
H
IJL
M6*45(*2+1)
K
ATTENTION: Lock pin
Klix cam

222
30min
Assemble Time Two People
Components List
Assembly Instruction
Components List
3
2
1
4
5
6
7
16
17
18
19
15
14
13
12
10
11
8
9
22 21
23
20
21
24
25 26
Angle iron
Power socket
Drawer handle
Drawer
27
NOTE：
Component(4)*2PCS
Component(5)*2PCS
Component(10)*2PCS
Component(13)*2PCS
Component(24)*2PCS

10
10
1
2
3
4
4
33
STEP 2 Attach tubing (3) and (4) to the assembled frame with screws(K and A).
Assembly Instruction
STEP 1 Connect frame (1) and (2) with tubing (10).
A*4
A*4
K*2
K
K
A
A

6
5
5
9
8
44
Assembly Instruction
STEP3
STEP 4
Attach tubing (5,6 and 9) with screws (A).
Attach modesty panel(8) to the assembled frame with screws(B).
A*6
B*4

7
19
B
14
16
55
Assembly Instruction
STEP 5
STEP 6
Attach iron mesh panel(7) and bottom panel(19) with screws (A and
B).
Attach table top to assmebled frame with screws(B).
A*4
B*4
B*16
A

11
25
12
13
13
14
66
Components List
Assembly Instruction
STEP 7
STEP 8 Put tubing(11,12,13 and 25)together with screws(A).
Attach the power socket to the table top with screws(H).
H*2
A*2
A
A

15
17
J
C
A
77
Components List
Assembly Instruction
STEP 9
Attach panels(15 and 17) to the frame assembled in the last step with
dowels(J) and screws(B). Please do NOT screw completely until all the
screws are right in the holes so that you can adjust the position easily
during the assembly process.
STEP 10 Attach the shelf assembled in the last step to the table with
screws(C and A).
B*9
J*2
A*6
C*6
C
A

2
20
21
23
21
D
D
A
F
D
18
I
I
24
Components List
Assembly Instruction
STEP 11 Attach shelf board to the frame with screws(A,F,D and G).
STEP 12
Screw the lock pins on the backside of front board of drawer(20) first.
And then insert side boads(21), bottom panel(23) and boards(24) with
casters to the slot of the front panel(20) of drawer. Insert the Klix cams
and turn right about 180° to lock tightly(Attention: Be sure to make the
arrow on the Klix cam right against the head of lock pin so that you
can insert the Klix cam completely into the holes.)
G*2
F*2
A*2
D*2
I*6
Attach the angle iron to the frame with screws(G)
first, and then attach the board(8) with screws(F,D
and A).
D*6
G
26
24
8

22
E
A
27
Components List
Assembly Instruction
STEP 13 attach backboard(22) to the drawer with screws(A).And then attach
the handle to front board of drawer(27) with screws(E).
STEP 14 Completed drawer.
A*6
E*2
9

Components List
Assembly Instruction
STEP 15 Put the assembled drawer in the bottom-right corner.
STEP 16 Place the non-woven drawer where you want to organize your stuffs.
10