SUNON DAM9003.058072 User manual

Please read this manual carefully before any operation and keep it properly for future use.
Assembly Manual
DAM9003.058072
Two-Drawer Nightstand

DAM9003.058072 Assembly Manual
Keep all parts out of the children’s reach.
WARNING Panels
TIPS：
01 02
1
4
5
13
13
8
2
7
9
9
11
2
12
12
10
3
You need to have a crosshead screwdriver beforehand.
Place all the panels on a clean and smooth surface, such as a rug or
carpet, to prevent them from being scratched.
Don’t tighten screws or bolts until all the pieces are fitted.
It is recommended to have 2 persons to complete the assembly.
If you have any issue regarding the product, please contact us at
[email protected].
Make sure that all parts in your product package, including panels and
accessories, match up with those listed in the Panels & Accessories list.
NOTE
CONTACT US
crosshead screwdriver Not included in package.
NOTE
In case of any doubts,contact Sunon.
3
Handle with care,protective layer is required.
2
Safe carriage,multi-people are needed.
1
6
The number in the picture indicates the corresponding panel type.
Please refer to the “Panel List” for details.

DAM9003.058072 Assembly Manual
Accessories List
Three-in-one Connector
L=25mm
A
（×24）
Phillips Flat-Head Screw
M4*14
D
（×16）
Phillips Pan Head Screw
M4*22
G
（×2）
Drawer Handle
27.5*26mm
H
（×2）
Phillips Flat-Head Screw
M4*35
E
（×8）
Drawer Slides
14”
F
（×2 Sets）
Dowel
8*40mm
B
（×28）
Three-in-one Screw
L=20mm
C
（×8）
Panel List
03 04
1
PanelsNumbers Size
Back Panel（×1）
720*530*16mm
2 2
Drawer Bottom（×2）
490*344*5mm
3
Bottom Panel（×1）
530*364*16mm
4
Top Panel（×1）
530*380*25mm
5
Shelf Panel（×1）
530*364*16mm
6
Bottom Front Panel（×1）
530*50*16mm
7
Upper Drawer Front（×1）526*150*16mm
8
Upper Drawer Back（×1）
480*76*12mm
9 9
Upper Drawer Side（×2）
350*76*12mm
10
Lower Drawer Front（×1）
526*260*16mm
11
Lower Drawer Back（×1）480*168*12mm
12 12
Lower Drawer Side（×2）
350*168*12mm
13 13
Side Panel（×2）
720*400*25mm

DAM9003.058072 Assembly Manual
Assembly Instructions
Step 1：
Step 2：
Step 3：
05 06
A
A
B
B
Three-in-one Connector
L=25mm
A
（×2）
Dowel
8*40mm
B
（×2）
Three-in-one Connector
L=25mm
A
（×2）
Dowel
8*40mm
B
（×2）
A
B6
B
A
6
6
33
1
Install 2 Dowels and 2 Three-in-one Connectors into holes in Bottom
Front Panel (No.6) .
1.Install 2 Dowels and 2 Three-in-one Connectorson Back
Panel(No.1).
2.Install Bottom Panel (No. 3) onto Bottom Front Panel (No. 6).
Connect the Bottom Front Panel (No. 6) to the Bottom Panel(No. 3).
Install Bottom Panel.
Install Back Panel.

Install 4 Dowels and 4 Three-in-one Connectors into holes in Back
Panel(No. 1), then install TopPanel (No.4) and shelf Panel (No.5) onto
Back Panel (No.1).
DAM9003.058072 Assembly Manual
Step 4：Install 2Top Panels.
07
Three-in-one Connector
L=25mm
A
（×4）
Dowel
8*40mm
B
（×4）
08
Separate Drawer Slides.Step 5：
Cabinet Member
Cabinet Member
Drawer Member
Drawer Member
3
1
4
5
A
A
A
B
B
B
6
Pull Out
UP

D
D
D
D
Install Drawer Slides.Step 7：
Three-in-one Connector
L=25mm
A
（×16）
Dowel
8*40mm
B
（×16）
Phillips Flat-Head Screw
M4*14 14”
DF
（×8） （×2 Set）
DAM9003.058072 Assembly Manual
Install 2 Side Panels.
09 10
Step 6：
Drawer Slides-Cabinet menber
4
5
3
13
13

C
C
E
E
E
E
C
Three-in-one Screw
L=20mm
C
（×4）
Phillips Flat-Head Screw
M4*35
E
（×4）
DAM9003.058072 Assembly Manual
11 12
Step 8：Step 9：
Install Upper Drawer-Part One. Install Upper Drawer-Part Two.
7
9
9
9
7
8
2
9
2
Install 4 3-in-1 Screws into holes in Upper Drawer Front Panel (No. 7),
then install Upper Drawer Side (No. 9) onto Upper Drawer Front (No. 7).
Drawer Bottom (No. 2) along the groove in Upper Drawer Side (No. 9)
into the groove in Upper Drawer Front (No. 7).
Install Upper Drawer Back Panel.
C

D
D
D
D
Three-in-one Screw
L=20mm
C
（×4）
Phillips Flat-Head Screw
M4*14
D
（×4）
Phillips Flat-Head Screw
M4*14
D
（×4）
14”
F
（×1 Set）
Drawer Slides
Phillips Flat-Head Screw
M4*35
E
（×4）
Step 10：Step 11：
Install Upper Drawer-Part Three. Install Lower Drawer (following Step 8、9 and 10).
DAM9003.058072 Assembly Manual
13 14
7
8
2
9
10
11
12
12
2
Install Drawer Member.
9
-Drawer Member
14”
F
（×1 Set）
Drawer Slides -Drawer Member

Phillips Pan Head Screw
M4*22
G
（×2）
Drawer Handle
27.5*26mm
H
（×2）
H
H
H
H
Step 12：
DAM9003.058072 Assembly Manual
Step 13：Install Drawer Handles.
15 16
Insert the Drawers.

DAM9003.058072 Assembly Manual
17 18
Done!
NOTE：Remove the Drawer.
If you want to remove the drawer,please pull the drawers all the way
out,then push the plastic tab of the ball bearing slide up on one side and
down in the other side,and then pull the drawer completely out.