Sunrise Medical Kid Kart Xpress Installation and operation manual

SUPPLIER:
THIS MANUAL MUST BE GIVEN TO THE USER
OR OWNER OF THIS DEPENDENT MOBILITY
BASE.
BEFORE USING THIS DEPENDENT MOBILITY
BASE READ THIS ENTIRE MANUAL AND SAVE
FOR FUTURE REFERENCE.
User
Instruction
Manual &
Warranty
Kid Kart Xpress
With Transit Option
Without Transit Option
A.R.T. Group is a division of Sunrise Medical

3
mkt3048 9921700000 Rev C
9921700000 Rev C
I. INTRODUCTION
A.R.T. GROUP LISTENS
Thank you for choosing this dependent mobility device. We want to hear your questions or comments
about this manual, the safety and reliability of your mobility device, and the service you receive from
your A.R.T. Group supplier. Please feel free to write or call us at the address and telephone
number below:
A.R.T. GROUP
7128 Ambassador Road
Baltimore, MD 21244
Toll Free 800-333-4000
Fax [phone]
www.artgrouprehab.com
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your mobility device best and can answer most of your questions about
safety, use and maintenance. For future reference, fill in the following:
Supplier: ____________________________________________________________
Address: ____________________________________________________________
____________________________________________________________________
Telephone:___________________________________________________________
Serial #:____________________________ Date/Purchased:___________

4
9921700000 Rev C mkt3048
II. TABLE OF CONTENTS
I. INTRODUCTION ........................................................................3
II. TABLE OF CONTENTS ................................................................4
III. YOUR XPRESS AND ITS PARTS .................................................6
IV. GENERAL WARNINGS ..............................................................8
A. Weight Limit............................................................................8
B. Getting To Know Your Xpress..................................................8
C. Safety Checklist .......................................................................8
D. Changes & Adjustments...........................................................8
E. Environmental Conditions .......................................................9
F. Street Use................................................................................9
G. Motor Vehicle Safety ...............................................................9
H. For Caregivers ...................................................................... 10
V. WARNINGS FOR SAFE USE .................................................... 11
A. Transit Use............................................................................ 11
B. Center of Balance.................................................................. 12
C. Dressing of Changing Clothes ............................................... 12
D. Obstacles.............................................................................. 12
E. Reaching or Leaning ............................................................. 12
F. Ramps, Slopes & Side Hills.................................................... 13
G. Transfers............................................................................... 13
H. Curbs & Steps....................................................................... 13
I. Climbing Stairs ..................................................................... 14
J. Descending Stairs ................................................................. 14
K. Escalators ............................................................................. 14
L. Maintenance......................................................................... 14
VI. WARNINGS FOR COMPONENTS & OPTIONS........................ 15
A. Transit Option ...................................................................... 15
B. Anti-Tip Tubes ...................................................................... 15
C. Tray Support......................................................................... 15
D. Cushions............................................................................... 15
E. Fasteners .............................................................................. 16
F. Footbeds .............................................................................. 16
G. Tires ..................................................................................... 16
H. Positioning Belts ................................................................... 16
I. Power Drive.......................................................................... 17
J. Attendant Handle................................................................. 17
K. Quick-Release Axles.............................................................. 17
L. Wheel Locks ......................................................................... 17
M.Modified Seat Systems ......................................................... 17
N. Upholstery Fabric ................................................................. 17
VII. OPERATING INSTRUCTIONS .................................................. 18
A. Wheel Locks ......................................................................... 18
B. Unfolding ............................................................................. 18
C. Folding ................................................................................. 19
D. Rear Wheel Removal & Installation ....................................... 21

5
mkt3048 9921700000 Rev C
E. Transit Use................................................................................22
F. Positioning Shell Installation.....................................................22
G. Positioning Shell Removal .........................................................23
H. Tilt-In-Space (TIS) Angle Adjustment........................................24
I. Hip Angle Adjustment ..............................................................24
J. Recline Adjustment...................................................................24
K. Knee Angle Adjustment............................................................25
L. Sunshade Installation & Adjustment .........................................25
M.Positioning & Growth Adjustments Guide ................................26
N. Seat Depth Adjustment ............................................................26
O. Standard Seat Cushion Adjustment...........................................27
P. Contoured Seating System Cushion Adj....................................27
Q. Standard Cushion without Lateral Hip Support.........................28
R. Back Positioning Plate Height Adjustment ...............................29
S. Back Cushion Height Adjustment..............................................29
T. Footbed Adjustments ...............................................................29
U. Pelvic Positioning Belt Length Adjustment................................30
V. Pelvic Positioning Belt Position Adjustment .............................. 31
W. Butterfly Harness......................................................................31
X. Lateral Trunk Supports Assembly to the Seating Shell................32
Y. Lateral Trunk Support Mounting, Operating, & Adjustment ......33
Z. Head Support Installation & Adjustment...................................34
AA.Dynamic Forehead Strap Installation & Adjustment.................35
BB. Hip Pads..................................................................................37
CC.Knee Abductor Installation ......................................................37
DD. Knee Abductor Block Adjustment .........................................38
EE.Tray Support Adjustment..........................................................38
FF.Tray Installation & Adjustment ..................................................38
GG.Foot Strap Adjustment............................................................39
HH. Shoe Holder Strap Adjustment...............................................39
VIII. MAINTENANCE...........................................................................40
IX. LIMITED WARRANTY..................................................................41
II. TABLE OF CONTENTS

6
9921700000 Rev C mkt3048
III. YOUR XPRESS AND ITS PARTS
KID KART XPRESS
1. Wheel locks
2. Safety Lockout Pin
3. Recline Control (optional)
4. Attendant handle adjustment control button
5. Transit Option (optional) Securement points
6. Footbed adjustment button
7. Anti-Tip tubes
8. Sunshade adjustment control
9. Positioning shell
10. Mobility base
11. Tilt in space block
12. Tilt in space adjustment mechanism
13. Tray support
14. Trigger mechanism
1
6
13
9
10
34
5
8
7
8
11
12
2
14
14
2
4

7
mkt3048 9921700000 Rev C
III. YOUR XPRESS AND ITS PARTS
Weight:
34 lbs.
Shell only weight: 16 lbs.
Base only weight: 18 lbs.
Color Options
Frame:
Purple, Silver, Pink, Black
Seating Shell Fabric Colors:
Jazz, Classic, Kaki-Smoke, Red-Black
Seat & Back Fabric Colors:
Black (US Only), Gray, Navy
Adjustment ranges:
Tilt range: 0-45°
Recline: 85° to 130°
Handle bar height: 36.5" to 41"
Seat depth: 5.5" to 13"
Seat width (at hip): 11.5"
w/opt. lateral hip supports 6.5"-10"
Knee width: 13"
w/opt. lateral knee supports 5"-11"
Top of head to seat: 13" to 22"
Top of shoulder to seat: 7.5" to 16"
Axilla (under arm) to seat: 4.5" to 12"
Chest width: 4" to 10"
Width of head: 3.75" to 7"
Shoulder width: 5" to 11"
Lower Leg/Foot: 5" to 14"
Footbed adjustment:
70° to 170° extension
Dimensions:
Overall Width: 24"
Floor-to-seat height: 21"
Folded dimensions: 24" X 28" X 20"
Seating Options:
Standard Cushion without-Lateral
Hip Support
Adjustable Contour Cushion w/o
Lateral Hip Support
All features may not be available with some
confiurations or in conjunction with another prod-
uct feature. Please consult your supplier or custom-
er service for more information. Your authorized
supplier can also provide you with more
information on accessories.
KID KART XPRESS TECHNICAL SPECIFICATIONS

8
9921700000 Rev C mkt3048
IV. GENERAL WARNINGS
Throughout this section, you will find general warnings for the safe use of your dependent mobility
device. It is important that you read and understand these warnings before you use this product. If you
fail to do so, a fall, tip over or loss of control may occur and cause severe injury to the rider, you
or others.
A. WEIGHT LIMIT
Never exceed the weight limit for the rider (55 lbs) or for items carried in the storage areas (15
lbs). The combined weight limit for the rider and storage areas is 70 pounds. Never use the mobility
device for more than one rider.
B. GETTING TO KNOW YOUR XPRESS
Read all instructions before using this product. In particular, you should:
1. Be trained in the safe use of this product by your health care professional.
2. Practice bending, reaching and transfers until you know the limit of your ability. Have someone
help you until you know what can cause a fall or tip over and how to avoid doing so.
3. Be aware that you must develop methods for safe use best suited to your level of function and
ability.
4. Never try a new maneuver on your own until you are sure you can do it safely.
5. Get to know the areas where you plan to use your mobility device. Look for hazards and learn
how to avoid them.
6. Always use anti-tip tubes when this product is unfolded and in use.
C. SAFETY CHECKLIST
Before each use of this product:
1. Wheel locks must be adjusted to maintain proper performance. Always engage the wheel locks
before transferring a child.
2. Make sure the mobility device rolls easily and that all parts work smoothly. Check for noise, vibra-
tion, or a change in ease of use. (They may indicate low tire pressure, loose fasteners, or other
damage).
3 Repair any problem you may encounter. Your authorized supplier can help you find and correct
any problems.
4 Check to see that both quick-release rear axles are locked. When locked, the axle button will "pop
out" fully. If not locked, the wheel may come off and cause a fall.
5 Lock the anti-tips in place.6. Never seat your child in the mobility device until is fully unfolded
and locked.
7. Use a pelvic positioning belt when the child is seated.
8. Never leave your child unattended.
D. CHANGES & ADJUSTMENTS
1. See your health care professional and have them adjust components and accessories as your child
grows.
2. Unauthorized modifications or use of parts not supplied or approved by Sunrise Medical may
change the product's structure. This will void the warranty and may cause a safety hazard.
!WARNING

9
mkt3048 9921700000 Rev C
IV. GENERAL WARNINGS
E. ENVIRONMENTAL CONDITIONS
1. Your mobility device is designed for use on firm, even surfaces such as concrete, asphalt and indoor
floors and carpeting.
2. Use extra care if you must use this mobility device on a wet or slick surface. If you are in doubt, ask
for help.
3. Do not use this product in a shower, pool or other bodies of water.
4. Do not operate your mobility device in sand, loose soil or over rough terrain.
F. STREET USE
1. This product is not intended for street use.
2. Be alert to the danger of motor vehicles on roads or in parking lots.
3. At night, or when lighting is poor, use reflective tape or clothing.
4. Due to your child's low position, it may be hard for drivers to see the rider. Make eye contact with
drivers before you go forward. When in doubt, yield until you are sure it is safe.
G. MOTOR VEHICLE SAFETY
As indicated on the front cover of this user manual, identify whether your chair has been
manufactured with the Transit Option installed.
NEVER USE THE MOBILITY DEVICE SHELL AS A CAR SEAT.
If your chair is NOT equipped with the Transit Option:
Mobility device products do not meet federal standards for motor vehicle seating.
1. NEVER let anyone sit in this product while in a moving vehicle.
2. ALWAYS move the rider to an approved vehicle seat.
3. ALWAYS secure the rider with proper motor vehicle restraints.
4. In an accident or sudden stop the rider may be thrown from the mobility device. Mobility device
pelvic positioning belts will not prevent this and further injury may result from these belts or straps.
5. NEVER transport this mobility device in the front seat of a vehicle. It may shift and interfere with the
driver.
6. When being transported in a vehicle, ALWAYS secure the unoccupied mobility device so that it
cannot roll or shift.
7. Do not use this product if it has been involved in a motor vehicle accident.
If your chair is equipped with the Transit Option:
See sections: Warnings for Safe Use: Transit Use (p. 11), Warnings for Components & Options
( p. 16) and the Operating Instructions (p. 22).
!WARNING

10
9921700000 Rev C mkt3048
IV. GENERAL WARNINGS
H. FOR CAREGIVERS
1. Work with the child's health care professional to learn safe methods best suited to your abilities and
those of your child.
2. To prevent injury to your back, use good posture and proper body mechanics when lifting or tilting
your child.
3. Remind the child to lean back when you tilt the mobility device backward.
4. When you descend a curb or single step, slowly lower the mobility device in one easy movement.
5. NEVER leave the child alone.
6. When making adjustments to the mobility device, always engage the wheel locks to help minimize
unintended movement.

11
mkt3048 9921700000 Rev C
V. WARNINGS FOR SAFE USE
Figure 1
AA
A. TRANSIT USE
1. If possible and feasible, the child should be transferred to a car seat and the vehicle restraint used.
2. If the mobility device is used for transport and has been installed with the Transit Option, it must
be used in a vehicle equipped for forward-facing securement during transport.
3. The rider must not weigh more than 55 lbs.
4. Figure 1 shows the location of the transit securement points (A) for this product.
5. Use only with Wheelchair Tiedown and Occupant Restraint Systems (WTORS) that have been
installed in accordance with the manufacturer's instructions and SAE J2249. (See your local medical
equipment supplier.)
6. Attach WTORS to securement points in accordance with the manufacturer's instructions and SAE
J2249.
7. Attach occupant restraints in accordance with the manufacturer's instructions and SAE J2249.
Note: To obtain a copy of SAE J2249 Wheelchair Tiedown and Occupant Restraint Systems for Use in
Motor Vehicles, please contact the Society of Automotive Engineers 724/776-4841 or www.sae.org/

12
9921700000 Rev C mkt3048
V. WARNINGS FOR SAFE USE
B. CENTER OF BALANCE
Kid Kart mobility devices are designed for stability and performance. The point where this device
will tip forward, back, or to the side depends on its center of balance and stability. The center of
balance is also affected by:
• The distance between the rear wheels.
• The seat height and seat angle.
• Backrest angle.
• Changes in your child's body position, postures or weight distribution.
• Pushing the mobility device on a ramp or slope.
• The use of a backpack or other options, and the amount of added weight.
To maintain the proper center of gravity and balance:
• Consult your therapist and supplier when the mobility device is set up.
• Consult your authorized supplier or therapist BEFORE you modify or adjust the mobility device.
• Use anti-tip tubes.
C. DRESSING OR CHANGING CLOTHES
Your child's weight may shift if you dress or change your child's clothes while they are seated in the
mobility device. To reduce the risk of a fall or tip over while changing clothes or diapers:
• Rotate the front casters until they are as far forward as possible.
• Engage the wheel locks
• Ensure that anti-tip tubes are in the down position.
D. OBSTACLES
Obstacles and road hazards (such as potholes and broken pavement) can damage your mobility device
and may cause a fall, tip over or loss of control. To avoid these risks:
• Scan the area well ahead for danger as you push the mobility device.
• Make sure the floor areas ahead are level and free of obstacles.
• Install a ramp at entry or exit doors. Make sure there is not a drop off at the bottom of the ramp.
E. REACHING OR LEANING
If your child reaches or leans it will affect the center of balance of your mobility device. This may cause
a fall or tip over.
• NEVER allow your child to reach or lean if they must shift their weight sideways, forward, or
backward and rise up off the seat.
• If your child must reach, move the mobility device as close as you can to the object they wish to
reach and rotate the front casters until they are as far forward as possible.
Note: To do this: Move your mobility device past the object you want to reach, then back up
alongside it.

13
mkt3048 9921700000 Rev C
V. WARNINGS FOR SAFE USE
F. RAMPS, SLOPES & SIDE HILLS
Pushing the mobility device on a slope, including ramps or hills, will change the center of balance. A few
safety reminders include:
1. Do not push this product on a slope steeper than 10%. (A 10% slope means: one foot in elevation for
every ten feet of slope length.)
2. Do not turn or change direction on a slope or ramp.
3. For your child's safety, ramps at home and work must meet all legal requirements for your area.
4. Always stay in the CENTER of the ramp.
5. Use a ramp with guardrails (or raised borders at least 3" high).
6. Always go straight up and straight down on hills or ramps.
7. Do not stop on a steep slope.
8. Watch for a drop-off at the bottom of a slope or ramp.
9. Do not engage the wheel locks to slow or stop your mobility device.
10. Beware of wet or slippery surfaces.
11. Do not recline or tilt the shell while going up hills.
12. Ask for help any time you are in doubt.
G. TRANSFERS
1. Work with your health care advisor to learn safe transfer and lifting methods.
2. Have someone help you until you know how to do a safe transfer of your child on your own.
3. Engage the wheel locks before you transfer. This keeps the rear wheels from rolling.
4. Move your child's mobility device as close as you can to the seat you are transferring to.
5. Rotate the front casters until they are as far forward as possible.
6. Transfer your child as far back onto the seat surface as you can. This will reduce the risk that the
mobility device will tip or move away from you.
H. CURBS & STEPS
Follow the instructions below for descending or climbing a stair or curb. Do not try to climb a high curb
or step (more than 4 high) unless you have help. Doing so may cause your mobility device to exceed its
balance point and tip over.
To descend a curb or single step going BACKWARD:
1. Stay at the rear of the mobility device.
2. Several feet before you reach the edge of the curb or step, turn the mobility around and pull it
backward.
3. While looking over your shoulder, carefully step back until you are off the curb or stair and standing on
the lower level.
4. Pull your mobility device toward you until the rear wheels reach the edge of the curb or step. Then
allow the rear wheels to slowly roll down onto the lower level.
5. When the rear wheels are safely on the lower level, tilt the mobility device back to its balance point.
This will lift the front casters off the curb or step.
6. Keep the mobility device in balance and take small steps backward. Turn the mobility device around
and gently lower front casters to the ground.

14
9921700000 Rev C mkt3048
V. WARNINGS FOR SAFE USE
TO CLIMB A STEP OR CURB GOING FORWARD:
1. Stay behind the mobility device.
2. Face the curb and tilt the mobility device up on the rear wheels so that the front casters clear the
curb or step.
3. Move forward, placing the front casters on the upper level as soon as you are sure they are past the
edge.
4. Continue forward until the rear wheels contact the face of the curb or step. Lift and roll the rear
wheels to the upper level.
I. CLIMBING STAIRS
1. Use at least two attendants to move this mobility device up stairs.
2. Move the mobility device and rider BACKWARD up the stairs.
3. The person at the rear is in control. He or she tilts the mobility device back to its balance point.
4. A second attendant at the front firmly grasps a non-detachable part of the front frame and lifts the
mobility device up and over one stair at a time. You may want to rotate the anti-tippers up so that
they do not interfere with steps.
5. The attendants move to the next stair up. Repeat for each stair, until you reach the landing.
J. DESCENDING STAIRS
1. Use at least two attendants to move an occupied mobility device down stairs.
2. Move the mobility device and rider FORWARD down the stairs.
3. The person at the rear is in control. He or she tilts the mobility device to the balance point of the rear
wheels and rolls it to the edge of the top step.
4. A second attendant stands on the third step from the top and grasps the frame. He or she lowers
the chair one step at a time by letting the rear wheels roll over the stair edge.
5. The attendants move to the next stair down. Repeat for each stair, until you reach the landing.
K. ESCALATORS
NEVER use this mobility device on an escalator, even with an attendant.
L. MAINTENANCE
Proper maintenance of your mobility device will ensure a long life for the product. Inspect and
maintain this mobility device per the Maintenance details listed in the back of this booklet. If you
detect a problem, make sure to service or repair the product before use.

15
mkt3048 9921700000 Rev C
VI. WARNINGS FOR COMPONENTS & OPTIONS
Below are warnings for various standard and optional components for your Xpress. (Options may vary
based on your Kid Kart model.) If you fail to heed these warnings, you may cause damage to your Kid
Kart, a fall, tip over or a loss of control that may cause severe injury to the child, caregiver or others.
A. TRANSIT OPTION
1. Use only Wheelchair Tiedown and Occupant Restraint Systems (WTORS) which meet the
requirements of SAE J2249 Recommended Practice - Wheelchair Tiedown and Occupant Restraint
Systems for Use in Motor Vehicles. Do not use WTORS designed to rely on the stroller structure to
transfer occupant restraint loads to the vehicle. (See page 11)
2a. The positioning shell/mobility base unit has been dynamically tested with the occupant facing
forward mode for a 30 mph (48-km/h) frontal impact test. The occupant must be facing forward
during transport if the occupant is greater than 20 pounds in weight.
2b. For infants (20 pounds or less in weight) the positioning shell/mobility base combination must be
facing to the rear. This means the shell is placed in the mobility base so the footbed is positioned
away from the handle bar and the occupant is facing the rear of the vehicle.
3. To reduce the potential of injury to vehicle occupants, mobility device mounted accessories, such as
trays and respiratory equipment, should be removed and secured separately.
4. Postural supports and positioning devices should not be relied on for occupant restraint.
5. Do not alter or substitute mobility device frame parts, components or seating.
6. Sudden stops or impacts may structurally damage your stroller. Mobility devices involved in such
incidents should be replaced.
B. ANTI-TIP TUBES
Anti-tip tubes can help keep your mobility device from tipping. Do not remove the anti-tip tubes and
use in down position whenever the base is unfolded.
C. TRAY SUPPORTS
1. Do not lift this product by its tray supports.
2. Do not rest drinks on tray supports.
D. CUSHIONS
This mobility device's seating was designed for comfort and postural support. If seating component modifi-
cations are necessary, consult your therapist or clinician.

16
9921700000 Rev C mkt3048
VI. WARNINGS FOR COMPONENTS & OPTIONS
E. FASTENERS
Many of the screws, screws and nuts on this product are special high-strength fasteners. ONLY use
fasteners provided by an authorized supplier (or ones of the same type and strength, as indicated
by the markings on the heads), do not over- or under-tightened fasteners, and If screws or screws
become loose, tighten them as soon as you can.
F. FOOTBEDS
1. At the lowest point, footbeds should be at least 2" off the ground. If set too low, footrest may
interfere with obstacles you may encounter during normal use.
2. Adjustment of the footbed may cause interference with the casters in some positions. This may
affect your ability to stear the Kart.
3. Avoid putting weight on the footbed. The mobility device may tip forward (or backward if shell has
been reversed).
4. Never lift this mobility device by the footbeds.
G. TIRES
Proper inflation extends the life of your tires and makes your mobility device easier to use. Do not
under- or over-inflate tires. Check weekly for proper inflation level, as listed on the tire side wall.
H. POSITIONING BELTS
Use positioning belts ONLY to help support the child's posture.
1. Make sure the rider does not slide down in the mobility device seat. The belts must be snug, but
must not be so tight that they interfere with breathing. You should be able to slide your open hand,
flat, between the belt and the rider.
2. Use positioning belts with a cooperative rider only. Make sure that you can remove the belts in an
emergency.
3. NEVER Use Positioning Belts:
• As a restraint.
• On a child who is comatose, agitated or is prone to seizures.
• As a motor vehicle restraint.

17
mkt3048 9921700000 Rev C
VI. WARNINGS FOR COMPONENTS & OPTIONS
I. POWER DRIVE
Do not install a power drive on this product.
J. ATTENDANT HANDLE
Your mobility device's attendant handle provides secure points for a caregiver to grasp the rear of this
Kart, to prevent a fall or tip over. Check to make sure handle is locked in place after adjusting height.
K. QUICK-RELEASE AXLES
If this product has quick-release axles, ensure that both quick-release rear axles are locked before
using this product. An axle is not locked until the quick-release button pops out fully. Quick-release
axles should be inspected for function and any signs of wear or bending.
L. WHEEL LOCKS
Never engage wheel locks to slow or stop this product when it is moving. To keep the rear wheels
from rolling, always engage both rear wheel locks when you transfer your child to or from this
mobility device. Make sure lock arms embed in tires at least 1/8" when locked.
M. MODIFIED SEATING SYSTEMS
Do not change the seating system of your Kart UNLESS you consult your health care professional.
N. UPHOLSTERY FABRIC
Replace worn or torn seating cover fabrics as soon as you can, and be aware that laundering or excess
moisture will reduce flame retardation of the fabric.

18
9921700000 Rev C mkt3048
VII. OPERATING INSTRUCTIONS
Figure 4 Figure 5
Figure 1 (Unlocked) Figure 2 (Locked)Wheel Lock Adjustment
Before seating a child always check that the mobility base is properly locked in its upright position,
that the fold lockout pin is inserted, and that the wheel locks are engaged.
A. WHEEL LOCK ADJUSTMENT
1. Loosen bolts and adjust wheel lock contact bar downwards. Lock arms should embed into tires
minimum of 1/8th inch when locked.
2. With the wheel locks on the rear wheels should skid, not roll when the Kid Kart is pushed with a
child in the product.
B. UNFOLDING
1. Unhook fold retaining strap and store in tray provided under seating shell.
2. Insert or rotate anti-tippers into a downward position facing the ground. (See Fig. 4)
3. Place the mobility base on the floor with wheel locks engaged. Make sure that the mobility base fold
lock out pin is not inserted into the lock out hole. (See Fig. 4)
4. Lift the handle bar over into locked position, then lift up so that the frame unfolds and locks into an
upright position. (See Fig. 5 and 6)
5. Insert the mobility base lock pin into the lockout hole. When inserted into the hole, the lock pin
prevents the rear wheels and axle from folding under the Kart.
Wheel Lock
Adjustment
Bolts

19
mkt3048 9921700000 Rev C
VII. OPERATING INSTRUCTIONS
Figure 6 Figure 7
6. If the shell is being installed separately, see positioning shell installation instructions on page 22.
To position the shell back, depress the recline lever and pull back. Adjust legrest, tilt and optional
recline to appropriate configuration. (See Fig. 7)
Figure 8
NOTE: Seating system removed for clairity
Figure 9
C. FOLDING FRAME AND ROTATING HANDLE INTO STORAGE POSITION
Your kid kart is equipped with two stage folding
1. Stage one (See Fig. 9) does not effect the stroller wheels and base allowing only the handle to be
brought forward to a storage position. This is useful for transporting the Kid Kart in the back of a
station wagon or van.
2. Stage two(See Fig.8) allows complete folding of the Kid Kart handle and base.
This folding system is accomplished via the two Stage trigger. (page 20)

20
9921700000 Rev C mkt3048
C1. TWO STAGE FOLDING
VII. OPERATING INSTRUCTIONS
Figure 2
Figure 1


C3. FOLDING FRAME COMPLETE
The mobility system folds compactly with the shell installed. The system is designed to fold with the
seat shell installed in the forward facing position.
1. Engage wheel locks. Remove the child from the seat shell.
2. Elevate legrests, tilt seat to most forward position and fold the back forward. (See instructions on
pages 24 & 25)
3. Pull the fold lockout pin out. (See Fig. 10)
4. Activate the trigger (See Fig. 2)
5. Holding the triggers and handle, pull back on the frame in the direction shown (See Fig. 4)
6. Rear wheels will move forward and frame will collapse. As soon as the rear axel begins to move
forward begin to rotate the push handle forward at the same time (See Fig.4)
7. Attach fold retaining strap to underside of storage tray
8. Rotate upward or remove anti-tipper
C2. HANDLE ONLY FOLDING (See Fig.3)
NOTE: With the locking pin installed (See Fig.10)
1. Remove the child from the seating system
2. Handle storage will work with or without the shell in the Kid Kart
3. Engage the wheel locks
4. Activate the trigger handle as shown. (See Fig.2)
5. Rotate the handle forward and continue rotating the handle to it's folded position. (See Fig.3)
6. As handle moves forward, release the trigger and rotate the handle (See Fig.3)
Figure 3
Figure 4