Sunrise Medical Quickie Q2 User manual

S E C T I O N E N G L I S H
A. REAR TRANSIT BRACKET INSTALL
Works with serial numbers after: Q2V-091821, Q2H-009882.
1. Pre-installation:
a. Place your Q2 Wheelchair on a Table or Flat work surface for best
installation results.
b. Remove the wheels, armrests, and any other obstruction to gain access
to the frame holes (A) that will secure the Rear Transit Bracket(J).
c. In the case of the Q2 Depth Adjustable Back odel, or (DAB). Loosen
and remove the 4 Screws (B) that hold the DAB Bracket (C) to the
Backrest tube (D) with a 5/32” hex key and 7/16” wrench. You will
need to remove and replace the outer bracket provided in your kit, and
and will re-use the inner DAB Bracket(E) as shown in Figure 3.
2. Install the Q2 Standard Rear Transit Brackets
a. Assemble the brackets and hardware for both sides of the chair as
shown in figure 2.
b. DO NOT use the hardware screw (G) unless you intend to install a
WC-19 approved Lap Belt.
c. ount the Pelvic belt between Screw(G) and pivot (I). The washer and
button head screw(G)(H) include a patch that is intended to be perma-
nent once installed.
d. Apply the Transit notification stickers using the guide on page 2
e. Torque all hardware to 144 in-lb.
3. Install the Q2 Transit Brackets for a DAB configuration
a. Assemble the Brackets and hardware for both sides of the chair as shown in
figure 3.
b. Reinstall the new DAB Transit bracket (K) reversing the order of the
instructions shown in Step1.
c. DO NOT use the hardware (G)(H) unless you intend to install a WC-
19 approved Lap Belt.
d. ount the Pelvic belt between Screw(G) and pivot (I). The washer and
button head screw(G)(H) include a patch that is intended to be perma-
nent once installed.
e. Apply the Transit notification stickers using the guide on page 2
f. Repeat this process for the other side of the wheelchair.
NOTE– Do not over-tighten the backrest plate pivot bolt as it may hinder the backrest
from folding properly.
1
2
0
15
15
30
30
45
TORQUE !TORQUE !
3
Parts included for Rear Transit:
1.4x 8 1.25x14 BH (rear)
2.4x 1/4-28 BH Capscrew (rear)
3.16x 1/4 flat washer (rear)
4.8x 1/4-28 Nylock nut (rear)
5.2x Rear T
ransit loop Std (L/R)
6.2x Rear T
ransit loop DAB
7.2x T
ransit Frame Saddle Std
8.2x DAB Seat/T
ransit Bracket
9.2x Wave Washer
10.2x Pelvic belt Hardware
Tools needed:
a.5mm hex key
b.5/32” hex key, 3/16” hex key
c.7/16” open end wrench
d.T
orque wrench and hex bits
e.21mm open end wrench
Q2 TRANSIT INSTALLATION (WC-19)
1
2
Please read these instructions carefully before beginning the installation. Failure to understand and follow installation instructions
may result in injury to installer and/or end user and may void the warranty. For more information on WC-19 Transit components,
or If you have any questions, call Sunrise edical Technical support at 800-333-4000 or go to www.sunrisemedical.com.
3
A
B
C
F
G
HJ
D
I
J
GH
B
I
Rear
view
E
K

SUNRISE EDICA L
Q2 T R A N SI T KIT I N S TA L L AT IO N WC- 19
B. FRONT TRANSIT BRACKET INSTALLATION
1. Assemble and Place the Front Transit Bracket
a. Assemble the brackets and hardware for both sides of the chair as
shown in figure 4.
b. For an easy installation, Start by sliding the Transit Insert(A) into the Front
Caster Tube and hold in place by threading one of the screws thru both
pieces. Assemble the Saddles, Washers, Transit hook (C), and caster barrel
with eccentric washers and screws and attach the Nylock nuts to hold it all
in place.
NOTE–Transit Insert (A) is required for Heavy Duty Transit Chairs.
c. Finish by tightening the 1/4-28 socket head screws (B) to a maximum
torque of 144 in-lb.
d. Repeat this process for the other side of the wheelchair.
C. CHECKOUT
1. Double-check Orientation and Torque on all Hardware.
a. Check that front and rear transit brackets have been installed evenly
from side to side as shown in
b. Using a torque wrench and socket wrench with a 3/16” and 7/32” hex
drive, check front and rear screws for correct torque.
c. Place Transit stickers in the areas noted in Figure 4
DEALER/TECHNICIAN WARNING
WARNING
Attention dealers and qualified technicians, do not operate or service this wheel-
chair without first reading the owners manual. If you do not understand the instruc-
tions and warnings in the owners manual please contact the Quickie Technical
Service Department before operating and/or servicing the Quickie wheelchair.
Failure to do so may result in damage and/or injury.
I PORTANT– Please see the Q2 owner’s manual and WC-19 Transit sup-
plement for additional warnings and information.
0
15
15
30
30
45
TORQUE !TORQUE !
4
4
C
A
B
©2014 Sunrise edical (US) LLC
9.14 K-100085 Rev.B
Customer Service: 800.333.4000
www.Sunrise edical.com
Sunrise edical • 2842 Business Park Ave. • Fresno, CA 93727 • USA
In Canada [phone]
Parts included for Front Transit:
1. 4x 1/4-28 SHCS (Front)
2. 2x 1” half saddle(Front)
3. 2x 1” saddle (Front)
4. 2x Front Transit Bracket
5. 2x Transit Insert(Front)
6. 4x 1/4-28 Automation nut
7. 4x 1/4 AN washer
8. 2x Transit Sticker