Sunrise Zippie ZONE/Q7 User manual

A. TELESCOPI G PUSH HA DLE I STALLATIO
1. Check or install Push Handle Insert
a. Place your Zippie Wheelchair on a Table or Flat work surface for best installation
results.
b. Make sure that the push handle insert (A) is in the correct orientation (figure 1),
BEFORE inserting the Push handles. If it is in the incorrect position, simply remove it,
flip it upside-down and re-insert into the receiver.
2. Install the telescoping Push Handles
a. Loosen the T-handle (B) so that the Push handle can be inserted.
b. Insert the Push handle(C) thru the opening in the receiver.
c. Install the hardware(D) on the bottom of the Push tube and tighten to about 30 in-lbs
so that it won’t pull out.
WAR I G
The Screw and ut (D) must be attached as shown in (figure 2) so that the Push handles do
not pull out of the receivers during use. This could cause the attendant to lose control of
the chair and in extreme cases, might lead to a fall or tip-over of the chair and it’s occupant.
d. Adjust the Push handle to the preferred height and Hand-tighten the T- handle (B)
e. Repeat the process with the other Push handle, making sure that the height is the
same on both sides when the installation is finished.
1 2
Tools needed:
a. 4mm hex key
b. 8mm and 10mm wrench
c. Torque wrench and hex bits
2
Please read these instructions carefully before beginning the installation. Failure to understand and follow installation instructions
may result in injury to installer and/or end user and may void the warranty. For more information on components, or If you have
any questions, call Sunrise Medical Technical support at 800-333-4000 or go to www.sunrisemedical.com.
ZONE/Q7 TELESCOPING PUSH HANDLE
INSTALLAT I O N
1
A
B
C
D
Top View
Receiver arm
and insert
Correct
Parallel
Incorrect
A
A

SU RISE ME DICA L ZONE/Q7 TELESCOPING PUSH HANDLE INSTA LL ATION
B. TELESCOPI G PUSH HA DLE KIT I STALLATIO
1. Install the handles:
a. Place your Zippie Wheelchair on a Table or Flat work surface for best installation
results.
b. The Push handle receivers should be pre-installed on the chair. If they have been
removed for some reason, attach the push handle receivers(E) to the backrest (F)
with the hardware shown. Tighten the Receiver attachment hardware to 55 in-lbs.
c. Make sure that the Push handle insert(A) in in the correct orientation (Figure 1)
before inserting the Push handle.
d. Attach the Push handle hardware(D), and adjust the Push handle to the preferred
height. Tighten the push handle tube locking knob(B).
e. Repeat the process with the other side, making sure that the Push handles are the
same height on both sides when finished.
C. CHECKOUT
1. Double-check Orientation and Torque on all Hardware.
a. Check to make sure the hardware on the bottom of the Push handle is attached
correctly (Figure 1)
b. The Push Handles should be parallel.
c. Make sure the T-handle is hand-tight against the stroller handle tube.
d. The Push handles should have the same height from side to side.
e. Using a torque wrench and socket wrench check all hardware for the correct
torque.
DEALER/TECH ICIA WAR I G
WAR I G
Attention dealers and qualified technicians, do not operate or service this wheelchair without
first reading the owners manual. If you do not understand the instructions and warnings in the
owners manual please contact the Zippie Technical Service Department before operating and/or
servicing the Zippie wheelchair. Failure to do so may result in damage and/or injury.
3
0
15
15
30
30
45
TORQUE !TORQUE !
©2014 Sunrise Medical (US) LLC
12.14 MK-100127 Rev.A
Customer Service: 800.333.4000
www.SunriseMedical.com
Sunrise Medical • 2842 Business Park Ave. • Fresno, CA 93727 • USA
In Canada [phone]
3
E
F
Parts included in this Kit:
1. 2x Bolt-on Push Handle
2. 2x M4 Screw
3. 2x ut
4. 2x DD insert
5. 2x 1/4-20 T-handle
A
B
D
C