Sunsight AAT30 User manual

Quick Start Guide
Models AAT30 & AAT15
Sunsight RF Panel Antenna Alignment System
Issue 7
June 2019
www.sunsight.com
[e-mail]
[phone] x2

The AATxx RF Panel Alignment System Components
(Optional Accessories Not Shown)
The AATxx RF Panel Antenna Side Mount

AAT Front
AAT Back
AAT Connectors
Important—use only Sunsight supplied charger. Other chargers will not charge the battery fully

Attention New Users!!
The AAT contains many additional features and functions not addressed in this
document. Refer to the AAT RF Panel Antenna Alignment System operator’s manual
for details. Read and understand all safety precautions as outlined in the manual.
Operator’s manual is available for download:
https://www.sunsight.com/support/aat-xx-support/
REVIEW THE FREE TRAINING VIDEOS:
https://www.sunsight.com/index.php/training
Important: Mount the AAT properly
Mount the AAT as high as possible to allow the GPS antennas on top of the AAT to
have an unrestricted view of the sky.
Remember that user’s hands, head, body, etc. can block GPS signals, as will most
other physical obstructions.
If necessary, refer to the Diagnostic webpage provided by the AAT’s onboard website
for details concerning azimuth/GPS conditions. This webpage will guide the user to
quick and successful resolution of most GPS signal issues.
Under normal conditions azimuth acquisition should take less than 5 minutes. To
learn tips and tricks for obtaining GPS - based azimuth refer to the general training
video: https://www.youtube.com/watch?v=WN-vKiaeR7I&list=PLHOFxsezxEnSFE2V-
im_Go-TO2PBF9AYW&index=36&t=0s

Getting Started
The AAT is a battery operated tool that measures azimuth, tilt, roll and height.
Typical use of the AAT is for aligning RF cellular panel antennas. The AAT kit comes
with all the basic items needed to perform most antenna alignment tasks.
To begin using the AAT, it is helpful to understand how the AAT functions.
The AAT is operated by accessing the unit using WiFi. The AAT acts as its own WiFi
hotspot.
The AAT can be operated by most any smartphone, tablet or laptop supporting standard Wi-Fi
(802.11b/g/n). See Section 3. for more details.
The AAT can measure and record results in two ways:
1) Quick Capture mode
OR
2) Profile mode
Quick Capture mode allows the user to mount the AAT and capture the actual
measurements with no need for alignment targets. Quick capture reports do not
include the target data that would be in the Profile mode reports.
Profile mode allows the user to preprogram the AAT with target data that is compared to
actual measurements in the field. Resulting reports show both target and measured
data. There are numerous optional data fields available when using the Profile mode.
Reports can be generated for a single alignment record (i.e. a single antenna) or site record
(i.e. where several alignment records create one report). The AAT can create PDF, CSV
and Google Earth files. Reports are downloaded to your handheld device or laptop by
the AAT, from there they can be emailed or printed.

Using the AAT
1) Secure the RF panel side mount
Position RF panel side mount as high as possible on the antenna to be measured.
Loop mount strap around antenna, then UNDER mount crossbar.
Feed strap end into ratchet buckle, and pull slack from strap.
Use the ratchet buckle to tighten strap. 2 –3 clicks is usually sufficient to secure
mount. DO NOT OVERTIGHTEN!
Ensure mount sits square on back/side of antenna. Adjust position as necessary.

2. Secure the AAT to mount
Secure AAT to mount by positioning upper lip of mounting rail on back of AAT into mount
grip, then rotate AAT into the security latch. User should feel AAT “click” into position.
Tighten both mount thumbscrews.
Secure AAT and mount to structure with the included safety lanyard. Attach lanyard to AAT
handle and through loop in mount strap.
3. Power on and connect to the AAT
The AAT can be accessed in two ways, 1) using the Sunsight Android app on a handheld
device (smartphone) or 2) directly in a web browser. The Android app includes more AAT
features (including the ability to capture photos to include in alignment reports). Web
browser access provides a basic method to operate the AAT when using non–Android
devices (IoS/Apple devices, Windows, or Linux).
Access Method 1. Connecting using the Sunsight Android app (preferred)
Download and install the Sunsight Android app from the support page at:
https://www.sunsight.com/support/AAT-xx-support/. Your Android device must be running
Android version 6.0 or higher and the AAT must have a firmware load of r005v45 or higher.
Power on the AAT.
Power on and enable Wi-Fi on the handheld Android device.
Launch the “Sunsight AAT” app.
Tap “Scan for AATs”
Highlight the appropriate AAT serial number from the dropdown list and click or tap
“Connect to AAT”.
Once connected, the green Link LED on the AAT keypad will illuminate and the
Measure Only page will appear on the handheld device.
Access Method 2. Connecting using basic web browser access (no app) - Applies to non-
Android devices (iOS/Apple, Windows, or Linux).
Power on the AAT.
Power on the device to be used with the AAT.
Enable WiFi if not already enabled.
Choose WiFi network AAT 901xxxx where the x’s represent the serial number of the
AAT.
Access the AAT by opening a web browser and navigating to:
192.168.0.50
Once connected, the green Link LED on the AAT keypad will illuminate and the
Measure Only page will appear on the handheld device.

*NOTE: If the Wi-Fi device is taken out of range of the AAT Wi-Fi broadcast, the device may automatically attempt
to connect to another Wi-Fi network or the cell network. This feature may be disabled by the user, if desired. See
device owner’s manual for more information.
Wi-Fi Hotspot Example

4. Using “Quick Capture” mode
Click or tap Menu, then select Measure Only.
Verify the Orientation is correct. Click or tap the Apply button to save any change to
Orientation. Orientation is referenced from behind the antenna. The AAT carrying
handle represents the front of the AAT.
On the live measurements page click or tap the Quick Capture button.
After the timer countdown, captured information will be displayed.
Click or tap the Next button to input site information and store to AAT or
Select Reject to return to the live measurements page to begin again.
Input Site, Sector and Antenna Position and save results.
Capturing alignment data using Quick Capture