superbrightleds WPR-NW40 User manual

Rotatable LED Wall Pack
Important: Read all instructions prior to installation.
User Manual
Part Number:
Conduit Mounting Installation
Rev Date: V1 10/13/2017Rev Date: V1 10/13/2017
5yr
WPR-NW40
WPR-NW80
1. Remove power from circuit.
2. Loosen 2 screws with 4mm Allen wrench
on bottom of light. Remove Bracket from
back of light.
3. Drill 4 holes on the wall using outer-most
holes on bracket as a guide. Drive wall
anchors into holes. Attach mounting
bracket to wall using 4 screws (not
provided).
4. Remove knockout from either side of light. Pull wires from conduit
through knockout. Attach conduit onto light. Make wire connections to
main supply.
3.15in
80mm
5.50in
139.69mm
4.90in
124.45mm
3.15in
80mm
5.50in
139.69mm
4.90in
124.45mm
3.15in
80mm
5.50in
139.69mm
4.90in
124.45mm
5. Mount light on bracket. Tighten 2
screws with 4mm Allen wrench on
bottom of light. Swivel aimable light
bar to desired position, and tighten
lock screw with 2mm Allen wrench.
Rotatable LED Wall Pack
User Manual
Part Number:
WPR-NW40, WPR-NW80

User Manual
Part Number:
Rotatable LED Wall Pack
Important: Read all instructions prior to installation.
Specifi cations
Rev Date: V1 10/13/2017
WPR-NW40
WPR-NW80
WPR-NW40
Intensity 4800 lm
Total Power Consumption 40 Watts
Operating Voltage Range 100~277 VAC
Beam Angle 60 degree
Color Temperature 4000 K
CRI >70
Operating Temperature -4~113°F (-20~45 °C)
IP Rating Weatherproof IP65
Dimmable No
Power Factor >0.90
Fixture Weight 2.1 lbs (1.95Kg)
Standards and Certifi cations RoHS, UL, DLC
Warranty 5 Years
WPR-NW80
Intensity 10,000 lm
Total Power Consumption 80 Watts
Operating Voltage Range 100~277 VAC
Beam Angle 60 degree / per head
Color Temperature 4000 K
CRI >70
Operating Temperature -4~113°F (-20~45 °C)
IP Rating Weatherproof IP65
Dimmable No
Power Factor >0.90
Fixture Weight 6.68 lbs (3.03Kg)
Standards and Certifi cations RoHS, UL, DLC
Warranty 5 Years
J-Box Installation Instructions
Warnings
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THIS PRODUCT AND THE HAZARDS INVOLVED.
1. Remove power from circuit.
2. Loosen 2 screws with 4mm Allen
wrench on bottom of light. Remove
Bracket from back of light.
3. Mount bracket to J-box with 2 screws (not
included). Bracket orientation needs to
have cut-out for wires pointing down. Pull
wires from J-box through bracket.
4. Temporarily hang light next to
J-box. Make wire connections to
main supply. Push connected wires
through bracket into J-box.
5. Mount light on bracket. Tighten 2
bracket plate screws with 4mm Allen
wrench on bottom of light. Swivel
aimable light bar to desired position,
and tighten lock screw with
2mm Allen wrench.
DLC Statement
Rotating LED Wall Pack meets DLC
requirement if beam is aimed in
downward position. Changing the
amiable beam to any other position
voids DLC certifi cation.
360°
4mm Screw
J-Box
2mm Lock Screw
Dual Head Wall Pack Confi gurations
Wire Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Green