superbrightleds FLCCT Series User manual

Selectable CCT LED Flood Light
Important: Read all instructions prior to installation. FLCCT Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V0.1 01/21/2020
5yr
Specications
Safety and Notes
Model FLCCT SW3515-SH8BRU SW3530-SH8BRU SW3550-SH8BRU SW3570-SH8BRU SW3590-SH8BRU
Beam Angle Nema 7x6 (115° horizontal x 85° vertical)
Operating Temperature -4°–122° F(-20°–50° C) -40°–122° F (-40°–50° C)
Environmental Rating IP65
Dimming none 1–10 V
• Product should be installed and serviced in accordance with
applicable national, state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that the main power
source and circuit breakers are switched o󰀨 before performing
any installation or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the
weight of the xture. Failure to properly support xture may result
in damage or injury, for which the manufacturer does not
assume responsibility. FLCCT-SW3530-SH8BRU
User Manual
Color Temperature Selection Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
Loosen screw on CCT selection switch cover to
access switch. With the light powered on, press
switch to cycle through CCT options. Re-tighten
switch cover screw.

Selectable CCT LED Flood Light
Important: Read all instructions prior to installation. FLCCT Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V0.1 01/21/2020
5yr
User Manual
Installation Instructions (Included U-bracket/Yoke Mount)
Installation Instructions (Optional Trunnion Mount)
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
1. Drill holes for mounting and wiring.
2. Attach trunnion mount to light using provided hardware.
3. Securely attach mount to wall and connect wiring.
4. Select desired CCT setting.
5. Rotate light to desired angle and tighten adjustment screws.
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
1. Drill holes for mounting and wiring.
2. Loosen light head adjustment screws with hex key.
3. Securely attach light to wall and connect wiring.
4. Select desired CCT setting.
5. Rotate light to desired angle and tighten adjustment screws.

Selectable CCT LED Flood Light
Important: Read all instructions prior to installation. FLCCT Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V0.1 01/21/2020
5yr
User Manual
Installation Instructions (Knuckle Mount)
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
1. Run wiring through knuckle mount as shown in diagram.
2. Assemble mount.
3. Open junction box and run wiring into box.
4. Securely mount light to junction box. Use sealant to create weatherproof seal.
5. Connect wiring.
6. Replace junction box cover.
7. Apply power and select desired CCT setting.
8. Rotate light head to desired angle and tighten adjustment screw.

Selectable CCT LED Flood Light
Important: Read all instructions prior to installation. FLCCT Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V0.1 01/21/2020
5yr
User Manual
Installation Instructions (Optional Pole/Slip-tter Mount)
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
light
wires
water-proof gasket
cover of junction-box
screw
knuckle mount
wiring
connections
hex
screw
Drill
Wall
hex-key
hex-key
cover screw
selection
switch
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
Pole/Post Installation
1. Disassemble mount and run wiring through it.
2. Reassemble mount.
3. Attach mount to light.
4. Drill mounting holes in pole/post and
attach mount.
Note: Installation on square poles will not require
round pole adapter plate or gasket. See illustration.
5. With supply power o󰀨, use access panel
to connect wiring.
6. Rotate light head to desired angle and
tighten adjustment screw.
Slip-tter Installation
1. Disassemble mount and run wiring through it.
2. Reassemble mount.
Note: Discard Pole/Post mount components.
3. Attach mount to light.
4. With supply power o󰀨, connect wiring.
5. Slide mount over pole/post and secure in place.
The maximum pole/post diameter is 2.375 in.
6. Rotate light head to desired angle and tighten
adjustment screw.
Only available on 70 W and 90 W lights.