superbrightleds FLCU Series User manual

High Watt LED Flood Lights
User Manual
Part Number:
Important: Read all instructions prior to installation. FLCU Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 09/30/2021
5yr
Specications
Operating Temperature -4~104°F (-20~40 °C)
IP Rating IP65
Fixture Weight 2.6 lbs (1.17Kg) 3.65 lbs (1.65Kg) 8.36 lbs (3.79Kg) 13.7 lbs (6.21Kg)
Specications FLCU-40K30-110 FLCU-40K50-60 FLCU-40K50-110 FLCU-40K100-60 FLCU-40K100-110 FLCU-40K200-110
Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Warnings
• This product should be installed by a fully certied electrician in accordance with
local building and electrical codes.
• Due to risk of electric shock, ensure that the main power source and circuit breakers
are switched o󰀨 before performing any installation or wiring procedures.
• Failure to properly support the xture during installation may cause damage or
injury, for which the manufacturer is not responsible. Ensure the light bracket is
securely mounted and will support the weight of the xture.
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.

High Watt LED Flood Lights
User Manual
Part Number:
Important: Read all instructions prior to installation. FLCU Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 09/30/2021
5yr
Instructions
flat wahser
wall
screw
hammer
expansion bolt
electrical drill
spring washer
screw nut
allen wrench
flat wahser
wall
screw
hammer
expansion bolt
electrical drill
spring washer
screw nut
allen wrench
1. Use the mounting bracket to mark out bolt holes
on the wall and then drill holes.(Fig 1)
2. Drive the bolts into the holes with the
threading facing outward.(Fig 2)
3. Place the mounting bracket over the bolts
and push it ush with the wall.(Fig 3)
flat wahser
wall
screw
hammer
expansion bolt
electrical drill
spring washer
screw nut
allen wrench
4. Fasten the nuts on the bolts to tighten the
mounting bracket to the wall.(Fig 4)
5. Rotate the light to the desired angle and
tighten screws with an allen driver. (Fig 5)

High Watt LED Flood Lights
User Manual
Part Number:
Important: Read all instructions prior to installation. FLCU Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 09/30/2021
5yr
Dimensional Drawings
6.59in
167.26mm
8.88in
225.47mm
7.93in
201.37mm
6.93in
176.02mm
CORD LENGTH
54.16in [1375.66mm]
.30in
7.62mm
3.05in
77.47mm
4.83in
122.68mm
.30in
7.62mm
1.00in
25.40mm
1.59in
40.39mm
2.57in
65.33mm
ADJUST ANGLE WITH
8MM WRENCH
MOUNTING BRACKET BASE
12.13in
307.98mm
10.81in
274.64mm
38.00in
965.20mm
14.91in
378.84mm
11.25in
285.75mm
1.60in
40.64mm
5.70in
144.74mm
2.17in
55.12mm
5.50in
139.70mm
4.20in
106.68mm
.60in
15.13mm
MOUNTING BRACKET BASE
ADJUST ANGLE WITH 4MM
AND 6MM HEX WRENCHES
FLCU-40K30-100
FLCU-40K50-60, FLCU-40K50-110
FLCU-40K100-60, FLCU-40K100-110 FCLU-40K200-110
7.50in
190.50mm
9.88in
250.83mm
10.25in
260.35mm
20.30in
515.62mm
10.11in
256.73mm
1.60in
40.64mm
4.10in
104.12mm
1.35in
34.33mm
.40in
10.16mm
5.50in
139.70mm
4.20in
106.68mm
TRUE
R.30in
7.62mm
ADJUST ANGLE WITH
4.5MM HEX
MOUNTING BRACKET BASE
7.50in
190.50mm
9.88in
250.83mm
10.25in
260.35mm
20.30in
515.62mm
10.11in
256.73mm
1.60in
40.64mm
4.10in
104.12mm
1.35in
34.33mm
.40in
10.16mm
5.50in
139.70mm
4.20in
106.68mm
TRUE
R.30in
7.62mm
ADJUST ANGLE WITH
4.5MM HEX
MOUNTING BRACKET BASE
13.75in
349.25mm
17.75in
450.85mm
19.13in
485.89mm
16.86in
428.25mm
36.30in
922.02mm
1.56in
39.62mm
2.32in
58.93mm
1.60in
40.64mm
6.70in
170.14mm
.38in
9.65mm
TRUE
R.23in
5.72mm
11.99in
304.55mm
10.50in
266.70mm
5.50in
139.70mm
4.20in
106.68mm
ADJUST ANGLE WITH
4MM AND 8MM HEX
MOUNTING BRACKET BASE
13.75in
349.25mm
17.75in
450.85mm
19.13in
485.89mm
16.86in
428.25mm
36.30in
922.02mm
1.56in
39.62mm
2.32in
58.93mm
1.60in
40.64mm
6.70in
170.14mm
.38in
9.65mm
TRUE
R.23in
5.72mm
11.99in
304.55mm
10.50in
266.70mm
5.50in
139.70mm
4.20in
106.68mm
ADJUST ANGLE WITH
4MM AND 8MM HEX
MOUNTING BRACKET BASE