Superior Signal SAFE-T-LOCK User manual

Unit to be installed by qualified technition.
Unit to be installed by qualified technition.
EL510
-1002
P
ROGRAMMABLE
CODE SWITCH
WARRANTY
• The
Safe-T-Lock™ /
Safe-T-Lock
™
Plus
is a sealed unit
.
R
emoving or tampering with t
he epoxy encapsul
ant will void the warranty
.
• Units damaged due to overload, abuse or incorrect installation will not be acce
pted
in warranty.
• Units have no serviceable parts.
This product is warranted against defects in materials or workmanship
for one year
for one year
from the date of purchase.
from the date of purchase.
Should service be required, the customer should return the
product for warranty consideration. Shipping will be prepaid via ground transportation.
All products requiring warranty service shall be returned
within one year from the date of
within one year from the date of
purchase.
purchase.
Exclusions from this warranty are the fi nish, and damage caused by improper
installation or use.
The manufacturer assumes no liability for costs incurred to remove or reinstall the
product, or for lost revenues due to equipment downtime.
This warranty gives you specifi c legal rights. You may also have other rights which vary
from state to state
and country to country.
TEMPLATE
INSTALLATION
INSTALLATION
INSTRUCTIONS
INSTRUCTIONS
Read and Save
Drill holes for #8 screw
(hardware not provided)
0.156" / 4mm
0.625" / 16mm
0.156" / 4mm
16355 SOUTH LONE ELM ROAD
OLATHE, KANSAS 66062
•
USA
TOL
L FREE:
800-447-3693
•
PHONE:
913-
780-1
440
•
FAX
:
913-780-1427
www.superiorsignals.com

INSTALLATION ON
VEHICLES WITHOUT KEY SWITCH
INSTALLATION
INSTALLATION
1. Mount the Safe-T-Lock™
/
Safe-T-Lock
™
Plus
Programmable Code Switch with
2, #8 screws. (not provided)
Recommend mounting in a easily accessible location, such as on the dash panel.
2.
Install provided bushing to protect wire from chafi ng.
3. After connected
, make sure the wires are not in tension.
Mounting Panel
Bushing
GRAY
BLACK
RED
WHITE
WHITE
RED W/STRIPE
BLUE
Seat
Switch
(1)
BATTERY NEGATIVE
OR POSITIVE
BATTERY NEGATIVE
BATTERY POSITIVE
POSITIVE FEED TO
VEHICLE
Fuse 10A
(2)
(3)
(4)
(4)
BLUE
(1) Unit will detect if the seat switch is normally open , normally closed and switch polarity.
(2) For bigger loads, an external relay must be used.
(3) Connection not required on vehicles without key switch
(4) (STL3000 only) Blue leads fror auxillary output
SAFE
-T-
LOCK
GRAY
BLACK
RED
(BAT)
(ION)
(ACC)
(ST)
WHITE
RED W/STRIPE
Seat
Switch
(1)
BATTERY POSITIVE
Positive feed
to vehicle
Fuse 10A
(2)
(3)
SAFE
-T-
LOCK
KEY SWITCH
STARTER SOLENOID
WHITE
(1) Unit will detect switch polarity.
(2) Switch must be normally open when seat is unoccupied
(3) For bigger loads, an external relay must be used.
(4) Automatically logs user out when key is turned off.
(5) (STL3000 only) Blue leads fror auxillary output
Mounting Panel
Bushing
BLUE
BATTERY NEGATIVE
OR POSITIVE
BATTERY NEGATIVE
(4)
(4)
BLUE
INPUT:
12-
1
20
VDC
0.5AMPS
/ 10
mA in stand by mode
OUTPUT:
Relay contact rating :
10
AMP
up to 24
,
1
AMP
36
VDC
a
nd higher
For bigger loads, an external relay must be used.
CONSTRUCTION:
Epoxy encapsulated
e
lectron
ics, unit is rated IP65. There ar
e no
user serviceable parts in this unit.
TECHNICAL SPECIFICATIONS
INSTALLATION ON
VEHICLES WITH KEY SWITCH
Unit to be installed by qualified technition.
Unit to be installed by qualified technition.
Unit to be installed by qualified technition.
Unit to be installed by qualified technition.
DIMENSIONS
4.23" / 107mm
1.41" / 36mm
3.94" / 100mm
4.23" / 100mm
0.16" /
4mm
0.94" /
24mm
0.62" / 16mm
2.72" / 69mm
0.14" / 3.5mm
3.52" / 89mm