Superior DRC6340TEN Owner's manual

P/N 506020-38
Rev. NC 03/2014
HEARTH PRODUCTS
SUPPLEMENTAL INSTRUCTIONS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
GLASS DOOR ASSEMBLY REMOVAL
SIGNATURE™SERIES GAS FIREPLACES
Figure 1
(2) Latch
Screws Glass Door
Assembly
Firebox Floor
(2) Door
Latches
~
~
Front View model shown.
Instructions also apply
to See-Through models.
Top Flange
CAUTION
RISK OF PERSONAL INJURY
OR PROPERTY DAMAGE.
•Do NOT abuse glass doors by striking or slamming shut
•Never operate fireplace with glass door assemblies removed.
These direct-vent appliances are designed to operate only when glass
door assemblies are installed. Generally, the glass door assemblies
should not be removed, except when access to components within
the firebox is required.
•Securely tighten door latch screws when reinstalling glass door
assemblies to prevent doors from falling out.
•Handle glass door assemblies with extreme care. Replace dam-
aged glass door assemblies with approved replacement assem-
blies only.
The door assemblies on this fireplace contain ceramic glass. Handle
with care to prevent damage. If the door frame or glass on either
assembly becomes damaged, replace the entire glass door assembly
with a manufacturer-approved replacement assembly only. Do not
attempt to substitute any materials used on door assemblies or
replace cracked or broken glass with any other materials.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
• Install only when fireplace is OFF and COLD.
• Fireplace surfaces get EXTREMELY HOT!
• The glass on the front of the fireplace reaches EXTREMELY HIGH
temperatures and can cause severe burns if touched. Even after
the gas is turned off, fireplace surfaces remain extremely hot.
• Keep children away from an operating fireplace. Closely supervise
children in any room where a fireplace is operating to prevent
contact with glass.
REQUIRED TOOLS
•#3Phillipsscrewdriver
REMOVING GLASS DOOR, MESH PULL SCREENS,
AND MODESTY PANEL
1) Remove the mesh pull screens, as follows:
a) Lift up the left end of the rod to disengage it from the slot in the left
rod bracket.
b) Slowly remove the right end of the rod from the hole in the right
rod bracket.
c) Set aside the rod and mesh pull screens for later reinstallation.
2) Remove the modesty panel from the top flange of the glass door by
firmly pulling up on it with both hands until it is disengaged.
3) Removeglassdoor,asfollows:
a) See Figure 1. While holding the top of the glass door frame in
place,usea#3Phillipsscrewdrivertoremovethetwo(2)screws
securingthedoorframetothetwo(2)doorlatches.
b) Carefullytiltthetopoftheglassdoorframeawayfromtheunit(as
shown in Figure 1), and then lift the door assembly up and out of
the lower track.
c) Carefully place the glass door assembly on a padded surface in a
safe location to prevent damage.
See other side for installation instructions.
Note: These instructions do NOT apply to the outer glass door
provided in the Outdoor Kit for indoor/outdoor installations of
Montebello See-Through models.
REMOVAL (AND REINSTALLATION) INSTRUCTIONS FOR GLASS DOOR ASSEMBLIES
FOR USE WITH DRT AND DRC SERIES DIRECT-VENT GAS FIREPLACES
(FRONT VIEW AND SEE-THROUGH MODELS*)
P506020-38
*ModelNumbers;DRC6340TEN,DRC6340TEP,DRC6340TYN,
DRT6340TEN,DRT6340TEPandDRT6340TYN,DRC6345TEN,
DRC6345TEP,DRC6345TYN,DRT6345TEN,DRT6345TEPandDRT-
6345TYN,See-ThroughModels:DRT63STTEN,DRT63STTEPand
DRT63STTYN
fire-parts.com

INSTALLING GLASS DOOR, MESH PULL SCREENS,
AND MODESTY PANEL
See WARNINGS and CAUTIONS on other side.
NOTICE: Only doors certified with the appliance shall be used.
AVIS : Seules des portes certifiées pour cet appareil doivent
être utilisées.
Note: These instructions do NOT apply to the outer glass door
provided in the Outdoor Kit for indoor/outdoor installations of
Montebello See-Through models.
1) Install glass door, as follows:
a) Retrieve the glass door. Visually inspect the gasket on the back of
the frame. Gasket surface must be clean, free of irregularities, and
seated firmly.
b) Position the door in front of the firebox opening, with the top of the
doorheldawayfromthereplace(seeFigure 1 on other side).
c) Lower the bottom of the door assembly onto the bottom door track,
engaging and centering it in the base channel, and then gently swing
the door up.
INNOVATIVEHEARTHPRODUCTS•SIGNATURE® DIRECT-VENTGASFIREPLACES•DOORREMOVAL/INSTALLATIONINSTRUCTIONS
d) Usinga#3Phillipsscrewdriver,fastenthedoorframetothedoor
latcheswiththetwo(2)latchscrews.Thelatchesshouldpullforward
to engage the door frame.
Note: Securely tighten latch screws when reinstalling glass door
assembly.
2) Install the modesty panel on the top flange of the glass door, as follows:
a) Graspthemodestypanelwithbothhands(withtheopenhemfacing
down).
b) Engage it with the upper lip of the glass door frame by pushing it
all the way down. Make sure the installed modesty panel is firmly
in place.
3) Installthemeshpullscreens,asfollows:
a) Retrieve the rod and two mesh pull screens. If necessary, attach
screens to rod.
b) Slowly insert the right end of the rod into the hole in the right rod
bracket.
c) Insert the left end of the rod into the slot in the left rod bracket.
P/N 506020-38 Rev. NC 03/2014
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
www.IHP.US.com
Innovative Hearth Products reserves the right
to make changes at any time, without notice,
in design, materials, specifications, prices and
also to discontinue colors,styles, andproducts.
Consult your local distributor for fireplace
codeinformationPrinted in U.S.A. © 2014
Innovative Hearth Products, LLC .
P506020-38
fire-parts.com