Supra TRAC-Guard Instruction Manual

TRAC-Guard™shroud
Installation user manual page 1
TRAC-Guard shroud overview
The Supra®TRACcess®TRAC-Guard™ padlock is a Bluetooth®-enabled padlock that provides
a exible access management solution for remote site locations. The padlock can be mounted
to most interior or exterior locations, such as cabinets, gates, fences, hatches, and covers.
The TRAC-Guard shroud helps protect against bolt cutters and hacksaws.
The instructions in this manual are applicable to the use of a Supra TRACcess TRAC-Guard
padlock shroud. Supra is not responsible for replacing padlock components damaged or
destroyed during installation.
Recommended: Install shroud on at surface in well-lit area before using TRAC-Guard
padlock in eld. Be careful not to lose hex screw or pin.
Note : Shackle clearance with shroud reduced to 0.875 ±0.50 inches as per diagram
on page 3.
Installing the shroud
Shackle must be removed before shroud can be installed. Follow the below directions to remove shackle.
Remove shackle
1. Use the shackle removal tool to rotate the hex screw
counterclockwise until removed.
2. Tap or shake padlock until the pin that was held in place by the
hex screw drops out.
Note: The rst time a pin is removed may require vigorous tapping
or shaking.
Release shackle, open padlock with eKEY
1. Turn on the padlock’s Bluetooth by pressing the center of the cylinder’s bottom and simultaneously rotating the cylinder either
clockwise or counterclockwise.
Note: A LED at the bottom of the cylinder will ash green after Bluetooth has been successfully activated.
2. Open TRACcess eKEY app and select Open Device.
3. Enter PIN and Access Code if needed.
4. Select Begin.
5. Wait for success message to appear, then rotate padlock cylinder clockwise until shackle releases.
6. To remove shackle from padlock body, you may need to open the padlock with eKEY a second time.
Note: If shackle spring pops out, reinsert spring into shackle opening directly above hex screw opening.
Contact us
Website : www.suprasystems.com/TRACcess
e-mail : [email protected]
Supra is part of UTC Climate, Controls & Security,
and a unit of United Technologies Corporation.
iOS is a registered trademark of Cisco Systems, Inc.
Android is a trademark of Google LLC.
Bluetooth is a registered trademark of Bluetooth SIG.
Other brand and product names are or may be the trademarks of, and
are used to identify products or services of, their respective owners.
P/N 10106362P1, EN

Install shroud
1. Once shackle has been removed from padlock body, insert
shackle into the opening on the long side of the shroud, as
indicated below.
2. With shackle inserted into shroud, position the long side of the
shackle directly over the shackle opening (above hex screw).
Slide the shackle into the lock body until you hear it click into
place.
3. Rotate shackle to align the short side of the shackle with
opening. The short side should rest almost ush with the lock
body as indicated below.
4. Insert pin (pointed end down) and insert hex screw. Use 5/64”
allen wrench to tighten hex screw clockwise.
Note: If shackle is closed prior to pin reinsertion, reopen padlock using
eKEY Open command.
5. Insert short side of shackle into opening, then press it all the way down to lock shackle into place.
TRAC-Guard™shroud
Installation user manual page 2

© 2019 United Technologies Corporation.
All rights reserved.
Ref. 1607 – TRAC-Guard shroud EN – 0117
TRAC-Guard™padlock
Installation user manual page 3
Remove shroud
1. Activate Bluetooth and open lock (opens one side of the shackle). 2. Raise shroud and use allen wrench to remove screw
(if necessary, tap padlock vigorously on hard surface
to remove pin).
3. Activate Bluetooth and open padlock with eKEY a second time.
Remove shackle completely.
4. Remove shroud. Reinstall shackle to padlock body, reinserting
set pin and hex screw.