Susteen Burner Breaker User manual
BURNER BREAKER
USER MANUAL
TABLE OF CONTENTS
Introduction
Precautions Prior/After Assembly
Utensils Required/MinimumRequirements
Parts List
Assembly Robot
Installing Burner Breaker Software
CHAPTER 1 Before Getting Started
Supported Devices and Passcode Types
Using Burner Breaker vs SvStrike
Usage Tips
How pincodes are accepted
Test if phone will wipe
Keeping phoneawake during attack
X and Y input fields
i
ii
iii
iiii
v
vi
1
2
3
4
5
6
7
Setting up USB Camera
Connecting to Camera
CHAPTER 2
Using BurnerBreaker
Menu Options
Advanced Options
Running the Attack
8
9
10-25
26
27
i
Introduction
Thank you for purchasing Susteen’s Revolutionary Burner Breaker! You have obtained the
most advanced pin code, passcode, and pattern lock breaking technology in the market.
You can now break into almost any Android smart phone that previously data could not be
obtained due to the phone being locked by pin code. You can also bypass pin codes on
popular prepaid phones sold thru Walmart, Target, Best Buy, etc., that are frequentlyused by
criminals.
For any Android phone whose operating system is at Android 6.0 and below, you will be
able to unlock the phone and access /acquire the device data.
Software is preprogrammed for various popular phone types such as Samsung Galaxy, ZTE,
LG,etc.Youcan alsouse our most popularpincode list toloadintoBurnerBreakerand
attack using specific pin codes.
ii
Precautions Prior/After Assembly
•
Do not wet the Robot or its part, or use/store them at high humidity or in an environment
where due condensation may occur.
•
Use the tools with utmost care paid to safety.
•
Do not disassemble the robot.
•
Care should be taken not to allow conductive foreign substances into contact with the
Robot
•
When you adjust or operate the Product after its assembly, secure sufficient work space
and operate. Handle the Product with utmost care because it may catch your finger while
operating.
•
When disconnecting a cable, hold its plug and connector.
iii
Utensils Required/Minimum Requirements
A.
Computer and Monitor:
•
Microsoft Windows 2000/XP/Vista/7
•
Pentium III, more than 1 GHZ recommended
•
Memory = 128(MB) RAM or Higher
•
Interface: USB Port x2
•
Display: (1024x768) or higher
B.
Phillips Screwdriver
iv
Parts List
Below is all items included for Burner Breaker. Before starting, check that all the following items
are included with your package. If anything is missing, contact us at support@susteen.com.
BurnerBreakerRobot Burner Breaker Base USB Camera Base screws (2) RubberFeet (4)
Magnets (4)
Spare Stylus
Tip (1)
ACAdapterforRobot USB Cable
(Robot to Computer)
SecureView All
Access Card
(Software loaded)
AOA Box Adapter
(PatternLock Phones)
v
Assembly Robot
Attach Robot to Base - Slide Robot Arm (1) into BB Base (2) (Picture Needed) and tighten/
secure using 2 base screws(4a and 4b) and Hex Screwdriver
Attach AC Adapter to Robot and power outlet
Plug Mini USB cable into Robot and computer
Position Robot: position BB so that power/USB outlet is facing to the right. (Picture needed)
*take care not to touch Stylus pen, may cause DE calibrate
Magnet Holders, Step 1:
•
Place the magnets to secure each cell phone to your metal plate.
•
Magnet holder height is adjustable for ease of use.
vi
Installing Burner BreakerSoftware
The Secure View All Access card contains the
Burner Breaker software.
Attach the Access card to your computer
and simply move/copy the folder to your
computer desktop.
Run the burnerbreaker.exefile to open
and run the program.
CHAPTER 1
Before Getting Started
1
Supported devices and passcode type
See if your device works with Burner Breaker by checking the list below.
Supported Devices
•
Android devices until Version 5.X
Supported passcode type
•
4 or more digit PIN
PIN/Password/Pattern list is configurable by user.
CHAPTER 1
Before Getting Started
2
Using Burner Breaker vs SVStrike
cell phones.
SV Strike acquires pincodes/
phones utilizing software.
3
CHAPTER 1
Getting Started
Usage Tips
Adjusting Computer Camera Settings
Sometimes computer camera settings will cause conflict with Ipevo USB Camera, causing the
Ipevo to not connect to the computer. To avoid this, go to device manager-Imaging Devices-
Integrated Camera- Turn OFF. You may need to restart the computer after this for the setting to
take place
Supervision Recommmended
It is suggested that someone be present while the Burner Breaker is in use.
Give Burner Breaker Breaks
The Burner Breaker uses a state of the art robot with interior sensors. It is suggested that the
robotbegivena“break”every5hourstoensureitscalibrationstaysintact.Thiscanbeas
simple as a five minute stop to ensure the stylus is hitting all the keys.
Confirm Camera Connection
Ensure your camera is connected and being accessed by the Burner Breaker software. This will
allow creation ofevidence.
Confirm Keys are Programmed Correctly
Take your time to make sure the Burner Breaker isprogrammedtohit allapplicable keys.
Different phonesandoperating systems willhave different ways ofregisteringpincode
attempts.YourBurnerBreakercanbeprogrammedfordifferenttime-outperiods,screen-awake
proceduresandeven backspace deletes for lockedapplicationswithout enter buttons.
4
CHAPTER 1
Getting Started
How pincodes areaccepted
This test with the phone is needed to be done
before using Burner Breaker to ensure proper,
continuous Brute Force attack
To find out how your phone accepts passcodes,
you need to manually enter incorrect passcodes
at least 5times.
It is very important to notate information like:
2
3
Do you have to enter “OK” after
each attempt to enter another
passcode?
How many attempts are you able to 1
enter before the phone locks out?
Howlong isthe lockout period?
Do you have to click “OK” on any
popup once the phone locks out to
get back to the keypad screen?
4
5
CHAPTER 1
Getting Started
Test if phone willwipe
ForAndroid6phones,itsamusttofind
outhowmanyattemptswouldtriggerthe
phone to wipe out, if it would at all.
To find if the phone will wipeout, always sit
with the phone forthe first 20-30attempts
tobreakin.Your phone will warn youifit
will wipe due to advanced security
settings. Warnings vary by manufacturer
but will most likely warn that phone will be
reset after alimitedamount ofleft over
attempts.
If you are sure that no attempts have been
made to enter pincodes, please use SV
Strike.
You only have 120 or so attempts to
acquire the pincode on this phone. It is
suggested that you manually enter the
pincodes based on our “Most Popular
Pincode” list.
6
CHAPTER 1
Getting Started
Keeping phone awake during attack
It is imperative that you find out how to keep your
phone awake during its lockout period. This can
be different between phone models and makes.
Most phones can be kept awake by using some
combinationoftapping“EmergencyCall”,or
pressing the “Home” or “Back” button. Other
phones can be kept awake by simply tapping on
the screen.
The phone must stay awake to stay onthe same
lockout schedule with the Burner Breaker because
thereisnowayfortheBurnerBreakertowakethe
phone itself if it sleeps.
Tip #1: Most phonesrequire you toclick“OK”
before you are able to keep the phone awake
during the lockout period.
Tip #2: Use preloaded excel sheet in All Access
cardtorecordmodelandsystemandtoinput
numbers for reference.
7
CHAPTER 1
Getting Started
X and Y input fields
The spaces between each button (which
you’llenterintoBurnerBreakerinterface)
are measured using X and Y coordinates.
The X axis moves from left to right. It uses a
postitive integer (+) when moving right, and
a negative integer (-) when moving left.
The Y axis moves up and down. It uses a
negative integer (-) when moving down, and
a positive integer (+) for moving up.
Whenmanuallyenteringanumberthatis
going left or down, make sure to use the “-“
symbol in front of the number.
(+)
Y axis
(-)
8
CHAPTER 1
Getting Started
(-)
X axis
(+)
9
CHAPTER 1
Getting Started
Setting up USB Camera
The includedUSBcamera is usedasboth
a sensor and an evidence capture camera.
Connect the camera’s USB to your
computer. The camera should be set up to
view the base of the robot with the phone
in frame. Once connected, the camera’s
viewpoint will be visible in the Burner
Breaker software interface.
The Burner Breaker software will create a
folder on your desktop, where it will store
evidencereportscontainingapictureof
each attempt to break into the phone. The
name of the files contained in the
evidencereportwillbethepincodeused
bytherobot.Forexample,ifthepicture
named “0007” shows the phone open, the
pincode to access the phone is “0007.”
Foradvancedsensorset up,please refer
to page 23.
10
CHAPTER 1
Getting Started
Connecting to Camera
To connect to the Burner Breaker,
hit the “Connect” button at the
top. Your Burner Breaker robot
should move and lock into center
position.
To connectto the camera, use
the drop down menu to find the
USB camera. Choose your
camera and hit connect. To
ensure no driver issues, use the
provided USB Camera.
11
CHAPTER 2
Using BurnerBreaker
Menu Options
Center Offset
Used to determine center of
phoneandoptimalphone
placement.
HitCenteroffsettomoveRobot
to start point. Place phoneunder
#5. The setting for X&Y field
shouldnotchangefrom(-55, 0).
Afterdoingthis, placeyour phone
on the base. The number “5”
should be directlyunder where
the stylus is lowered, after
clicking on “Center Offset”.
Table of contents
