Swann Retro SFA12610BN User manual

Retro 16” (40cm) Stand Fan
Model: SFA12610 (all colours)
Help line
0333 220 6050 v2.0
SFA12610_IM.indd 1 18/01/2019 08:38

2
When using any electrical appliance, basic safety
precautions should always be followed including the
following:
• Always ensure that the voltage on the rating label
corresponds to the mains voltage in your home
• Incorrect operation and improper use can damage the
appliance and cause injury to the user.
• This appliance can be used by children aged from 8
years and above if they have been given supervision or
instruction concerning use of the appliance in a safe way
and if they understand the hazards involved. Cleaning and
user maintenance shall not be made by children unless
they are older than 8 and supervised. Keep the appliance
and its cord out of reach of children aged less than 8
years. Check the power cord and plug regularly for any
damage. If the cord or the plug is damaged, it must be
replaced by the manufacturer or qualified person in order
to avoid an electrical hazard.
• Appliances can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved.
• Do not use the appliance if it has been dropped or
damaged in any way. In case of damage, take the unit in
for examination and/or repair by an authorised service
agent.
• Never immerse the unit in water or any other liquid for
IMPORTANT INFORMATION - RETAIN FOR FUTURE USE
SFA12610_IM.indd 2 18/01/2019 08:38

3
IMPORTANT INFORMATION - RETAIN FOR FUTURE USE
cleaning purposes.
• Remove the plug from the socket by gripping the plug.
Do not pull on the cord to disconnect the appliance from
the mains. Always unplug the unit when not in use, before
cleaning or when adding or removing parts.
• The use of accessory attachments that are not
recommended or supplied by the manufacturer may
result in injuries, fire or electric shock.
• Do not let the cord hang over the edge of a table or
counter. Ensure that the cord is not in a position where it
can be pulled on inadvertently.
• Do not allow the cord to touch hot surfaces and do not
place on or near a hot gas or electric burner or in a
heated oven.
• Do not use the appliance on a gas or electric cooking top
or over or near an open flame.
• Use of an extension cord with this appliance is not
recommended. However, if it is necessary to use an
extension lead, ensure that the lead is suited to the power
consumption of the appliance to avoid overheating of
extension cord, appliance or plug point. Do not place the
extension cord in a position where it can be pulled on by
children or animals or tripped over.
• This appliance is not suitable for outdoor use. Do not use
the appliance for anything other than its intended use.
• Do not carry the appliance by the power cord.
• Do not leave the appliance unattended during use. Always
unplug the unit when not in use or before cleaning.
• Always operate the appliance on a smooth, even, stable
SFA12610_IM.indd 3 18/01/2019 08:38

4
IMPORTANT INFORMATION - RETAIN FOR FUTURE USE
surface. Do not place the unit on a hot surface.
• Ensure that the unit is switched off after use.
• The manufacturer does not accept responsibility for any
damage or injury caused by improper or incorrect use, or
for repairs carried out by unauthorised personnel.
• In case of technical problems, switch off the product and
do not attempt to repair it yourself. Return the appliance to
an authorised service facility for examination, adjustment
or repair. Always insist on the use of original spare parts.
Failure to comply with the above mentions precautions
and instructions, could affect the safe operation of this
product.
• Your appliance must never be switched on through an
external timer or any kind of separate remote control
system
• This appliance is intended to be used in household and
similar applications such as: staff kitchen areas, in shops,
offices and other working environments; farm houses;
by clients in hotels, motels and other residential type
environments; bed and breakfast type environments.
• Keep loose clothing and hair away from the fan
SFA12610_IM.indd 4 18/01/2019 08:38

5
WHAT’S IN THE BOX
Rear Grille
Front Grille
Base
Fan Blade
Fan Nut
Motor assembly
Base Screw
remove before
assembly
Grille Screw & Nut
in small bag taped to grille
Remove all items from the packaging and check they are all present as shown in the
above image. Please note: the Grille Screw & Nut is in a small bag that is taped to
the grille so it doesn’t get lost in the box!
Please note: you are going to need a Phillips screw driver.
Weight
Telescopic
Shaft
SFA12610_IM.indd 5 18/01/2019 08:38

6
ASSEMBLY
Place the Weight in the base as shown and secure it all together with the Base
Screw. It only needs to be hand tight.
1. Remove the screw from the Motor Unit. Slide it over the Telescopic Shaft. Line up
the holes then refit the screw.
2. Use a Phillips screwdriver to remove the 4 screws from the motor unit. Set them
aside so they don’t get lost.
Remove the Base Screw from the Telescopic Shaft and set aside. Put the base on
the floor and press the Telescopic Shaft into it. It should click into place. This helps
with the next step.
1 2
SFA12610_IM.indd 6 18/01/2019 08:38

7
ASSEMBLY
Note: Handle goes at the top
Offer the Rear Grille up to the motor unit. Ensure the handle is at the top. Refit the 4
screws to secure the Rear Grille.
Fit the fan blade over the motor shaft. Make sure the notch in the fan aligns with
the peg on the motor shaft. Fit the Fan Nut to secure the blade. Note: turn ANTI-
CLOCKWISE to tighten it.
Note alignment!
SFA12610_IM.indd 7 18/01/2019 08:38

8
ASSEMBLY
Hook the Front Grille over
the Rear Grill - making sure
it is the right way up
Securing
clip. Open
all of them
at this stage
Grille Screw & Nut
in small bag taped to grille
Open all the securing clips on the Front Grille. There is a hook at the top of the Front
Grille. This hooks over the Rear Grille. This helps to keep the Front Grille the right
way up.
At the bottom of the Front Grille, there is a small hole. This needs to line up with a
corresponding hole in the Rear Grille.
SFA12610_IM.indd 8 18/01/2019 08:38

9
ASSEMBLY
Fit the Grille Screw & Nut and tighten, as shown above. It’s a bit fiddly but safety
regulations say there has to the a screw and nut there!
Finally, press the grille securing clips into place. This will keep the front and rear
grilles together. Now you are good to go!
SFA12610_IM.indd 9 18/01/2019 08:38

10
CLEANING & MAINTENANCE
Your fan requires little maintenance and contains no user serviceable parts.
Do not attempt to dismantle the unit yourself. The fan is permanently lubri-
cated and will not require additional lubrication.
Cleaning:
• Always unplug the fan from the mains outlet before cleaning.
• The fan can be cleaned with a soft dry cloth. Deposits of dust can be re-
moved by using a vacuum cleaner, ensuring that the air vents and grilles
remain free from dust to prevent overheating.
• Important: Do not allow water to run into the interior of the fan, as this
can cause an electric shock.
• Do not use abrasive cleaners or chemical agents to clean the product.
• When not in use, store the fan in it’s retail box.
TECHNICAL DATA
• Turn the speed control to selected speeds: 0 (off) and 1 (slow), 2 (me-
dium), 3 (fast)
• Set the tilt angle by adjusting the fan head accordingly.
• You can tighten/loosen the screw on the neck of the fan to lock the tilt
angle
• Never touch the blades with hands or any object. Keep long hair away
from the fan blades
• There is an oscillation control on top of the fan motor. Press down to
make the fan sweep left and right. Lift up to stop the oscillation motion.
• You can adjust the height of the fan by loosening the larger screw on the
Telescopic Shaft, setting your preferred height, then tightening it again.
HOW TO USE
Description: RETRO 16” (40cm) STAND FAN
Model: SFA12610 (all colours)
Input Voltage: 220-240V ~ 50Hz 50 Watts
SFA12610_IM.indd 10 18/01/2019 08:38