Swegon GOLDen GATE Lonworks FTT-10 User manual

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice. www.swegon.com 1
INSTALLATION GOLDen GATE Lonworks FTT-10,
TBLZ-3-1-1-41 and TBLZ-1-2-1-41
1. General
The GOLDen GATE Lonworks communiction unit is avail-
able in a number of kits for connecting up to GOLD and
COMPACT units of various generations.
In addition to the communication unit itself (part no.
019400), each kit also includes connection cables.
TBLZ-3-1-1-41 Communications kit
Intended for use together with the Version B/C/D/E/F
GOLD air handling units and COMPACT air handling units.
TBLZ-1-2-1-41 Communications kit
Intended for use together with the Version 4/A GOLD air
handling units.
Safety precautions
Be careful when you connect leads to the unit. Never con-
nect
leads to the unit while the supply voltage is switched on.
Doing so may
result in injury to you and damage the unit. Observe local
electrical safety regulations when carrying out the electri-
cal installation work.
Communication unit
The unit consists of the following components:
1. 4-module standard enclosure for DIN-rail mounting to
IP20.
2. 9-pin D-subconnector for connection via serial cable
to
computer for configuration or to a Version 4/A/B
GOLD unit.
3. Terminal for a 10-30 V AC/DC, 25 mA power supply
for 24 V
4. Terminal block for EIA 485 network
(Used by Version C/D GOLD units)
5. DIL switch for the termination of the EIA 485 network
6. Terminal block for the LonWorks network.
7. ”Service-Request” PIN.
8. Service LED.
9. Module Status LED.
10. Serial Status LED.
Fig. 1
24
5
1
7
17 18 19 20 21 22 23 24
Net B Net A Net B Net A SHL D NC GND Vin+
6 3
1 (A)
2 (B)
3 (NC)
4 (GND)
10
9
8

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice.
2 www.swegon.com
Fig. 2
Fig. 3
2. Configuring
The communication unit must be configured before it can
be put into operation. Energize the unit with 24 V AC,
temporarily or according to the description in Section 4,
Installation.
Configure the unit by means of the configuration soft-
ware:
GOLDen GATE Config which is available from our website.
Address
http://www.swegon.com, under Software. Install the
computer program according the instructions in the set-up
window.
A computer with Windows 98 or better is required, as well
as an RS-232 serial port. Use the serial cable, supplied,
with double 9-pin D-subconnectors. Start the configura-
tion program and select Golden Gate LonWorks,
See Fig. 2.
Select the appropriate serial port and version (GOLD 4A, B,
C, D, E, F or COMPACT), see Figure 3.
Get Config=Current setting and program version in the
communication unit.
Set Config=Tranfer the settings in the configuration pro-
gram to the communication unit.
Upgrade FW=Downloads the new software for the version
required into the communication unit. Open the preferred
program file. It is located in the ”GOLDen GATE Config”
folder installed.
Open the relevant file and it will be installed in the unit
connected.
A window will appear when the unit has been pro-
grammed. After the installation has been completed, it
may be necessary to switch off and switch on the supply
voltage to the communication unit.

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice. www.swegon.com 3
3. Installation
3.1 GOLD, Version E/F
Place the communication unit on the DIN rail inside the
electrical equipment cubicle of the air handling unit or
inside an optional enclosure.
Connect the 24 V AC supply voltage to terminals Vin+
(24) and GND (23). Supply voltage can be obtained from
the control unit of the air handling unit, see below and B
in Fig. 4.
GOLDen GATE GOLD
Terminal 24 (Vin+) Terminal 31 (G)
Terminal 23 (GND) Terminal 32 (G0)
Connect the network from the GOLDen GATE communi-
cation unit to the control unit of the GOLD (A in Fig. 4).
Use a 3-wire cable.
GOLDen GATE GOLD
Terminal 1 (A) Terminal 1 (A)
Terminal 2 (B) Terminal 2 (B)
Terminal 3 (Not used)
Terminal 4 (GND) Terminal 3 (GND)
The DIL switch must be in the ON position (see Fig. 1, Item
5).
Connect the Lonworks-network to the communication
unit, NET A (terminal 18 or 20), NET B (terminal 17 or 19)
and shield, if required, to SHLD (terminal 21).
Communication between the communication unit and the
air handling unit is activated by choosing LON in the hand-
held terminal under Functions/Communication/EIA-485.
See also the Operating and Maintenance Instructions for
the GOLD.
Fig. 4
SD
WLAN
CPU 1
CPU 2
1
A2 B3 GND 4 +5 -6 +7 -8 +9 -10
+11 -12 +13 -
SA TempCom 5Com 4Com 3Com 2Com 1
14
+15 -16 +17 -18 +19 -
Heat Cool
20
C21 NO 22 C23 NO 24 C25 NO 26 C27 NO 28 P29 G30 G0 31 G32 G0
24V AC
Sensor 1 Sensor 2 Sensor 4Sensor 3 Com 6 Com 7 Com 8 Com 9 Com 10 Com 11
+
33 - 34 G 35 G0 36 Y 37 U 38 39 40
24V AC In
41 42
18V AC In
45 46
230V AC In
4743 44
230V AC Out
BA

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice.
4 www.swegon.com
3.2 GOLD, Version C/D
Place the communication unit on the DIN rail inside the
electrical equipment cubicle of the air handling unit or
inside an optional enclosure.
Connect the 24 V AC supply voltage to terminals Vin+
(24) and GND (23). Supply voltage can be obtained from
the control unit of the air handling unit, see below and B
in Fig. 5.
GOLDen GATE GOLD
Terminal 24 (Vin+) Terminal 58 or 60 (G)
Terminal 23 (GND) Terminal 59 or 61 (G0)
Connect the network from the GOLDen GATE communi-
cation unit to the control unit of the GOLD (A in Fig. 5).
Use a 3-wire cable.
GOLDen GATE GOLD
Terminal 1 (A) Terminal 27 (A)
Terminal 2 (B) Terminal 28 (B)
Terminal 3 (Not used)
Terminal 4 (GND) Terminal 29 (GND)
The DIL switch must be in the ON position (see Fig. 1, Item
5).
Connect the Lonworks-network to the communication
unit, NET A (terminal 18 or 20), NET B (terminal 17 or 19)
and shield, if required, to SHLD (terminal 21).
Start communication between the communication unit
and the air handling unit by entering the settings de-
scribed below. The search path in the hand-held micro ter-
minal is the following: SETTINGS/INSTALLATION/COMMU-
NICATION/EIA485 and PROTOCOL/SETTINGS. See also the
Operating and Maintenance Instructions for the GOLD.
Select the setting: LONWORKS/TREND under EIA-485/
PROTOCOL.
Check to make sure that the following values are set un-
der: EIA-485/SETTINGS.
Address = 1.
Speed = 38400
Parity = none.
Stop bits = 1.
Fig. 5
A B

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice. www.swegon.com 5
12 34 56 78 910111213
1415 16 17 18 19 20 21 22 23 24 25 26 2728 29 3031 32 3334 3536 37
ON
3.3 COMPACT
Place the communication unit on the DIN rail inside the
electrical equipment cubicle of the air handling unit or
inside an optional enclosure.
Connect the 24 V AC supply voltage to terminals Vin+
(24) and GND (23). Supply voltage can be obtained from
the control unit of the air handling unit, see below and B
in Figure 6.
GOLDen GATE COMPACT
Terminal 24 (Vin+) Terminal 9 (G)
Terminal 23 (GND) Terminal 10 (G0)
Connect the network from the GOLDen GATE communi-
cation unit to the control unit of the COMPACT unit (A in
Fig. 6). Use a 3-wire cable.
GOLDen GATE COMPACT
Terminal 1 (A) Terminal 11 (A)
Terminal 2 (B) Terminal 12 (B)
Terminal 3 (Not used)
Terminal 4 (GND) Terminal 13 (GND)
The DIL switch must be in the ON position (see Fig. 1, Item
5).
Connect the Lonworks-network to the communication
unit, NET A (terminal 18 or 20), NET B (terminal 17 or 19)
and shield, if required, to SHLD (terminal 21).
Start communication between the communication unit
and the air handling unit by entering the settings de-
scribed below. The search path in the control panel is the
following: SETTINGS/INSTALLATION/COMMUNICATION/
EIA485 and PROTOCOL/SETTINGS. See also the Operating
and Maintenance Instructions for the COMPACT.
Select the setting: LONWORKS/TREND under EIA-485/
PROTOCOL.
Check to make sure that the following values are set un-
der: EIA-485/SETTINGS.
Address = 1.
Speed = 38400
Parity = none.
Stop bits = 1.
Fig. 6
AB

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice.
6 www.swegon.com
3.4 GOLD, Version B
Place the communication unit on the DIN rail at the side of
the junction hood of the air handling unit.
Connect the 24 V AC supply voltage to terminals Vin+
(24) and GND (23). Supply voltage can be obtained from
the electrical equipment cubicle of the air handling unit,
see below.
GOLDen GATE GOLD
Terminal 24 (Vin+) Terminal 104 (G)
Terminal 23 (GND) Terminal 103 (G0)
Connect the network from the GOLDen GATE commu-
nication unit (Item 2 in Fig. 1) to the control unit in the
GOLD (tapping for LON in Fig. 7). Use the data communi-
cation cable supplied.
DIL switch no. 4 on the GOLD air handling unit’s control
unit must be in the ON position, and DIL switch no. 3 must
be in the OFF position (see Fig. 7).
Connect the Lonworks-network to the communication
unit, NET A (terminal 18 or 20), NET B (terminal 17 or 19)
and shield, if required, to SHLD (terminal 21).
Fig. 7
Tapping for LON
DIL selector switch
Control unit

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice. www.swegon.com 7
A
4. General particulars
Service
Flashes if the unit has not been configured in the Lon-
Works network.
Module Status
Flashes green while the unit is energized.
Flashes red if the unit has not been configured via the
Golden Gate Config. software.
Serial Status
Flashes green when the unit communicates with the
GOLD unit.
Is lit with red glow when the network is missing. The LON
network connections must be re-established by a network
operator.
Other Particulars
Closing terminations must be used for the system to oper-
ate correctly. The network operator determines the type of
termination depending on the selected type of bus topol-
ogy in use.
3.5 GOLD, Version 4 and Version A
Place the communication unit on the DIN rail at the top of
the air handling by the quick connector sockets and cable
lead-throughs.
Connect the 24 V AC supply voltage to terminals Vin+
(24) and GND (23). Supply voltage can be obtained from
the control unit of the air handling unit, see below and
Fig. 8.
GOLDen GATE GOLD
Terminal 24 (Vin+) Terminal 9 (G)
Terminal 23 (GND) Terminal 7 (G0)
Connect the network from the GOLDen GATE communi-
cation unit to the control unit of the GOLD unit. Use the
communication cable supplied. The communication cable
has a 4-pin round quick connector and a 9-pin D-subcon-
nector. Connect between Connection A in Fig. 8 and Item
2 in Fig. 1.
Connect the Lonworks-network to the communication
unit, NET A (terminal 18 or 20), NET B (terminal 17 or 19)
and shield, if required, to SHLD (terminal 21).
Start communication between the communication unit
and the air handling unit by setting LON COMMUNICA-
TION to 0 in the hand-held micro terminal.
By pressing the ”Service Request PIN” pushbutton, the
network operator obtains the individual identification
code of the communication unit.
When communication is established, a list of the available
parameters can be fetched from the communication unit.
The parameters that are required can be selected from this
list. This list is also located as an “xif file” in the ”GOLDen
GATE Config” folder installed. The parameters for Version
C are also described in the Function Profile that is avail-
able from our home page at www.swegon.com under
Products/Air handling units/GOLD One-piece unit. Please
contact Swegon for particulars of other versions.
The GOLD air handling units operate independent of
whether or not the LON network is active.
Fig. 8

GB.TBLZ41.160408
Registered design. The company reserves the right to make design changes without prior notice.
8 www.swegon.com