Swegons VARIZON DIR 400 User manual

1
DIR
VARIZON®Displacement unit with adjustable spread pattern
DIR
Quick facts
►Adjustable spread pattern and affected area
►Suitable for all types of rooms
►Simple to install
►Cleanable
►Concealed fixing
►Available in alternative colours
►Included in the MagiCAD and CadVent databases
Quick guide
A I R F L O W - S O U N D L E V E L
DIR l/s
Size 25 dB(A) 30 dB(A) 35 dB(A)
400 34 40 48
500 47 57 66
600 60 71 85
900 110 130 148
The sound data applies to the displacement unit together
with the connection duct.

2
DIR
We reserve the right to alter specifications. 20111222 www.swegon.com
Technical description
Design
The DIR is a complete, flat displacement unit for mount-
ing recessed into studded walls. The unit consists of a
two parts: the plenum box and the perforated front plate.
The plenum box is equipped with a air volume measuring
point, or mounting frame and a rectangular connection
spigot. The telescopic mounting frame has a distribution
plate which is equipped with a number of adjustable
deflectors. This plate is removable for access to the duct
system. The perforated front plate is fixed to the mount-
ing frame.
Materials and surface treatment
The displacement unit is manufactured in galvanised sheet
steel and is coated with our pure white standard paint,
RAL 9010. The unit is also available in other standard
colours: Dusty grey 7037, white aluminium RAL 9006,
jet black RAL 9005, grey aluminium RAL 9007 and signal
white RAL 9003 (NCS 0500).
Customisation
In addition to the standard sizes, these displacement units
are available in special dimensions, with reinforced front
panels etc. Please contact your nearest sales representa-
tive for further information.
Accessories
Connection duct:
DIRT 4a. A rectangular connection duct with a circular
duct connection and a rubber seal. The connection duct
is telescopic by 300 mm in height.
Planning
It is possible to modify the affected area by adjusting the
deflectors behind the perforated front plate. This does
not affect the air flow, pressure drop or sound level. This
flexibility simplifies any future changes in the furnishing of
the room etc.
Installation
The plenum box is mounted before the wall board is
fixed. The plenum box is screwed into place through the
sides. The hole for the connection sleeve inlet is cut as
illustrated in the diagram. The wall board is then fixed in
place, the mounting frame pushed inside the displace-
ment unit and fixed using screws. Finally the front panel is
hung in place on the mounting frame. See Figure 1.
Commissioning
The measurement outlet is on the lower edge of the
displacement unit. The k-factor of the unit is stated in
the product label, and can also be found on our website
in the relevant k-factor guide. It is recommended that a
measurement unit and commissioning damper is used to
regulate the air flow. It should be placed before the inlet
of the connection duct. See Figure 2.
Maintenance
The displacement unit can be cleaned when necessary
using luke warm water with added detergen. The duct
system is accessed by removing the perforated front plate
and the distribution plate. See Figure 2.

3
DIR
We reserve the right to alter specifications. 20111222 www.swegon.com
DIR
Sizing
• Sound level dB(A) applies to rooms of 10 m2 equivalent
absorption area.
• Recommended maximum under temperature 6 K.
• To calculate the width of the spread pattern, air veloci-
ties in the zone of occupation or sound levels in rooms
with other dimensions, please refer to our calculation
programmes ProAir web, which is available for down-
load at www.swegon.com.
Sound data - DIR
Sound power level Lw(dB)
Table KOK
Size Mid-frequency (octave band) Hz
DIR 63 125 250 500 1000 2000 4000 8000
400 -6 9 2 4 -2 -12 -19 -20
500 3 5 2 4 -1 -11 -18 -19
600 -1 -2 0 3 1 -10 -17 -19
900 -8 1 1 4 -1 -11 -19 -18
Tol. ± 2 2 2 2 2 2 2 2
Figure 1. Installation. Figure 2. Commissioning. Maintenance.
Sound attenuation DL (dB)
Table DL
Size Mid-frequency (octave band) Hz
DIR 63 125 250 500 1000 2000 4000 8000
400 18 13 10 79487
500 18 13 10 69587
600 18 13 7 4 7 6 7 6
900 13 8 4 2 1 0 0 0
Tol. ± 2 2 2 2 2 2 2 2

4
DIR
We reserve the right to alter specifications. 20111222 www.swegon.com
DIR 600 DIR 900
Engineering graphs
Air flow – Pressure drop – Sound level – Affected area
• The size of the affected area is related to the isovel limit
of 0.2 m/s at D t 3 K and 6 K. D t in this case signifies the
difference between the room air temperature measured
at 1.2 m above the floor and the supply air temperature,
it is not the difference between the exhaust air and the
supply air temperatures. The air velocity is measured
with the displacement unit 0.5 m above the floor.
• The graphs are not to be used for commissioning.
• ∇ = min. air flow to obtain sufficient commissioning
pressure.
• The dB(C) value is normally 6-9 dB higher than the
dB(A) value.
• For D t = 6 K the measurements a
0,20
and b0,20 are
increased by approx. 20%.
DIR 500
DIR 400
ptPa
40 50 100200 m3/h
10 20 30 40 50 l/s 100
3
4
5
10
20
30
40
50
100
20
25
30
35
40 dB(A)
0,30,40,5 1 2
0,5 1 2 3 4
m
0,2
a
m
0,2
b
t -3°∆
ptPa
100200300400500 m3/h
20 30 40 50 100 l/s 200
3
4
5
10
20
30
40
50
100
20
25
30
35
40 dB(A)
1 2 3 4 5
1 2 3 4 5
m
0,2
a
m
0,2
b
t -3°∆
p
t
Pa
2003004005001000 m
3
/h
50 100200300400 l/s 500
3
4
5
10
20
30
40
50
100
20
25
30
35
40 dB(A)
1 2 3 4 5
2 3 4 5 10
m
0,2
a
m
0,2
b
t -3°
∆
p
t
Pa
100200300400500 m
3
/h
20 30 40 50 100 l/s 200
3
4
5
10
20
30
40
50
100
20
25
30
35
40 dB(A)
0,5 1 2 3 4
1 2 3 4 5
m
0,2
a
m
0,2
b
t -3°
∆
Figure 3. Affected area.

5
DIR
We reserve the right to alter specifications. 20111222 www.swegon.com
DIR
Dimensions and weights
DIR
Size A B D E F G ØH
400 402 343 402 345 50 80 99
500 502 443 502 445 50 80 124
600 602 543 602 545 50 80 159
900 602 543 902 845 70 100 199
Size J K L M N Weight, kg
Diffuser
Weight, kg
Duct
400 72 80-102 254 252 54 5 5
500 86 80-102 304 302 54 8 7
600 105 80-102 354 352 54 10 10
900 125 100 -122 504 502 74 15 12
Figure 4. Flush mounting measurements for the DIR.
1. Front panel
2. Connection sleeve
3. Commissioning box
4. Fixing frame
Figure 5. DIR and DIRT 4.

6
DIR
We reserve the right to alter specifications. 20111222 www.swegon.com
Order key
Product
Flush-mounted displacement unit DIR c-aaa
Version
Size: 400, 500, 600, 900
Accessories
Connection duct DIRT 4 a -aaa
Version
Size: 400, 500, 600, 900
Specification example
SD XX
Swegons VARIZON® rectangular low velocity terminal for
flush mounting in walls, of type DIR, with the following
functions:
• Adjustable spread pattern and affected area
• Air volume measuring point
• Cleanable
• Telescopic mounting frame
• Telescopic connection duct
• Powder coated in white, RAL 9010
Accessories:
Connection duct: DIRT 4 aaa xx items
Size: DIRc aaa xx items