Swisher POL10544C User manual

POLARIS
44” FINISH CUT
TRAILMOWER
OWNER’S
MANUAL
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 PHONE [phone]
FAX [phone]
MODEL NO.
POL10544C
Manufacturing quality lawn care equipment since 1945
Assembly
Operation
Service and Adjustment
Repair Parts
Made In The
USA
Rev. 05 041
Read and follow all Safety
Precautions and
Instructions before
operating this equipment.
IMPORTANT
swisherinc.com
10020
STARTING SERIAL #:
L204-159001

LIMITED WARRANTY
The manufacturer’ warranty to the original con umer purcha er i : Thi product i free from
defect in material and workman hip for a period of one (1) year from the date of purcha e
by the original con umer purcha er. We will repair or replace, at our di cretion, part found to
be defective due to material or workman hip. Thi warranty i ubject to the following
limitation and exclu ion :
1) Engine Warranty all engine utilized on our product ha a eparate warranty
extended to them by the individual engine manufacturer. Any
engine ervice difficulty i the re pon ibility of the engine
manufacturer and in no way i Swi her Mower Co., Inc. or it
agent re pon ible for the engine warranty. The Brigg &
Stratton Engine Service Hot-Line i 1-800-233-3723. The
Tecum eh Engine Service Hot-Line i 1-800-558-5402.
2) Commercial U e the warranty period for any product u ed for commercial or rental
i limited to ninety day from the date of original purcha e.
3) Limitation thi warranty applie only to product , which have been
properly a embled, adju ted, and operated in accordance with
the in truction contained within thi manual. Thi warranty
doe not apply to any product of Swi her Mower Co., Inc., that
ha been ubject to alteration, mi u e, abu e, improper a embly
or in tallation, hipping damage, or to normal wear of the
product.
4) Exclu ion excluded from thi warranty are normal wear, normal
adju tment , and normal maintenance.
In the event you have a claim under thi warranty, you mu t return the product to an
authorized ervice dealer. All tran portation charge , damage, or lo incurred during
tran portation of part ubmitted for replacement or repair under thi warranty hall be borne
by the purcha er. Should you have any que tion concerning thi warranty, plea e contact u
toll-free at 1-800-222-8183. The model number, erial number, date of purcha e, and the
name of the authorized Swi her dealer from whom you purcha ed the mower will be needed
before any warranty claim can be proce ed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME
PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some tate do not
allow the limitation of con equential damage or limitation on how long an implied warranty
may la t, o the above limitation or exclu ion may not apply to you. Thi warranty give
you pecific legal right and you may have other right , which vary from tate-to- tate. Thi i
a limited warranty a defined by the Magnu on-Mo Act of 1975.
2

This Safety Alert Symbol indicates important messages in this
manual. When you see this symbol, carefully read the message that
follows and be alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands, feet, and throw
objects. Failure to observe the following safety instructions could result in serious
injury or death.
SAFETY PRECAUTIONS
• Read the manual. Learn to operate thi machine afely.
• Alway di connect the park plug wire and place the wire where it cannot
contact the park plug, to prevent accidental tarting of the engine when etting
up, tran porting, adju ting or making repair .
• Keep all hield and guard in
place.
• Under tand the peed, teering and tability of thi machine. Know the
po ition and operation of all control before you operate thi machine. Check
all of the control in a afe area before tarting to work with thi machine.
• Clear the area of object uch a rock , toy , wire, etc. that can be picked up
and thrown by the blade.
• Allow only re pon ible adult who are familiar with the e in truction to
operate thi machine. Never allow children to operate thi machine.
• Be ure the area i clear of other people before mowing. Be aware of the
mower di charge direction and do not point at anyone. Stop the machine if
anyone enter the mowing area. Children are often attracted to the machine and
the mowing activity. Never assume that children will remain where you last saw
them.Keep children under the watchful care of another re pon ible adult.
•No riders!
• Do not put hand or feet near or under rotating part . Keep clear of the
di charge opening at all time .
• Do not mow in rever e. Alway look down and behind before and while
backing.
3

• Turn off the blade when not mowing. Before leaving the machine, turn off the
blade and top the engine.
• Watch for traffic when operating near or cro ing roadway .
• Do not operate the mower if it ha been dropped or damaged in any manner
or if the mower vibrate exce ively. Exce ive vibration i an indication of
damage. Repair mower a nece ary.
• Dre properly. Do not operate the mower when barefoot or wearing open
andal . Wear only olid hoe with good traction when mowing.
• Do not operate the machine while under the influence of alcohol or drug .
• Operate elf-propelled machine up and down lope . There i ignificant ri k
of overturn when operating acro lope . Operate walk-behind machine acro
lope . There i a ignificant ri k of lipping under a walk-behind machine when
operating up and down lope . Do not operate on lope greater than 15 degree .
• Never tamper with afety device . Check their proper operation regularly.
• Stop and in pect the equipment if you trike an object. Repair, if nece ary,
before re tarting.
• Never make adju tment or repair with the engine running.
• Mower blade are harp and can cut. Wrap the blade or wear glove , and
u e extra caution when ervicing them.
4

OD36 Deflector Decal
OD45-Warning Decal
OD103-Single Point Height Adju t Decal
OD29-Danger Decal
Engine Serial #
OD11-No Step Decal
OD15 Void Warranty Decal
OD33-Speed Decal
OD55-Triangle Danger Decal
(All four deck corner )
TrailMower Serial #
SAFETY DECALS
Replace decal immediately if damaged. Order by part number from Swi her Mower and Machine Co. Inc.
OD75-Polari Decal
(Not Pictured)
OD99127-44" Deck White Decal
(Not Pictured)
OD99127-44" Deck White Decal
(Not Pictured)
5

OPERATING YOUR TRAILMOWER
INTENDED USE
The 44” TrailMower i de igned to produce a quality fini h cut on lawn , golf cour e ,
etc. It i not intended to clear bru h or cut apling . Your TrailMower hould be
towed behind an ATV, golf cart, lawn tractor, or other approved vehicle. It i not
de igned for peed exceeding 5 MPH.
WARNING: To avoid eriou injury,
operate your mower up and down the face of lope , NEVER acro the face. DO
NOT MOW SLOPES GREATER THAN 15 DEGREES! (See attached guide for
ighting lope .)
ATTACHING TRAILMOWER TO TOW VEHICLE
• Back vehicle up to de ired towing po ition.
• Off et the TrailMower to the ide oppo ite the tow vehicle di charge (if any).
Thi prevent the tow vehicle from throwing gra into TrailMower engine.
• Bolt wivel hitch (H10) to tow vehicle receiver. If tow vehicle ha a ball hitch,
the ball mu t be removed before wivel hitch can be fa tened.
• Attach tow hitch (4582) to the wivel hitch with hitch pin (H11). Make certain
the hitch pin goe completely through each piece and i clipped to prevent
accidental eparation. (FIGURE FOUR)
• Securely attach afety tether (6736) to tow vehicle and to the TrailMower
toggle witch located on right ide of the engine. The afety tether will top the
TrailMower engine either manually or if the two hould become eparated. It is
very important that the safety tether is securely attached to both the toggle
switch and to the tow vehicle. (FIGURE TWO)
The operation of any mower can produce foreign object to be thrown into the
eye , re ulting in evere eye damage. Alway wear certified afety gla e or
wide-vi ion afety goggle over pectacle before taring any cutting machine
and while operating uch a machine.
The operation of any cutter produce ound wave that are damaging to the
human ear. Ear protection i recommended.
CAUTION!
Tragic accident can occur if the operator i not alert to the pre ence of
children. Children are often attracted to the machine and the mowing
activity. Never assume that children will remain where you last saw
them.
TRANSPORTING MOWER
• Stop TrailMower.
• Place TrailMower deck in it highe t po ition.
• When tran porting unattached from tow vehicle, remove park plug wire
and place it where it cannot contact the park plug.
6

• Set vehicle parking brake or chock wheel to prevent accidental rolling.
• Start engine properly.
• Slowly, engage blade control.
• In a afe environment, i.e. no children, allow blade to rotate and engine to
idle for 5 minute . Thi break in the belt and the engine.
• Stop mower properly.
ENGAGING BLADES (without T handle option, Standard)
The TrailMower will not tart if the blade lever i in the “ENGAGED” po ition.
• Engage blade by rotating blade lever into the “ENGAGED” po ition.
• Rotate blade lever in oppo ite direction to di engage blade.
• The dual braking y tem i applied when the blade become di engaged. It i
de igned to bring the blade to quick top (approximately 7 econd ). Each
TrailMower brake y tem ha been te ted and calibrated. For afety, the
con umer hould not alter the braking y tem.
ENGAGING BLADES (with T handle option, for order information see detail)
The TrailMower will not tart if the T-handle con ole i in the “ENGAGED”
po ition.
• Engage blade by pulling T-handle lever into it horizontal po ition.
• Return lever to it vertical po ition to di engage blade .
• The dual braking y tem i applied when the blade become di engaged. It
i de igned to bring the blade to quick top (approximately 7 econd ). Each
TrailMower brake y tem ha been te ted and calibrated. For afety, the
con umer hould not alter the braking y tem.
STARTING THE ENGINE
See engine manufacturer’ recommendation for the type and amount of oil and fuel
u ed. Trail Mower equipped with an electric tart engine will need a battery ( old
eparately). Swi her recommend u ing a tandard “12N12A” battery.
• Make ure the tow vehicle parking brake i et, mower i level, and blade are
di engaged. Engine mu t be level to accurately check and fill oil. Do not overfill.
• Check park plug wire, oil, and fuel.
• Check all electrical connection for build-up or debri .
• Make ure toggle witch i not turned “OFF” and afety tether i attached.
• Set engine idle to “CHOKE” po ition.
• With feet clear of mower deck, turn key witch to the “START” po ition; relea e
when engine begin to run (12volt model ). Recoil model mu t u e pull-rope.
Pull rope with a ingle fluid motion.
• Set engine throttle at maximum RPM.
• Allow engine to run a few moment before engaging blade .
BREAKING IN YOUR MOWER
CAUTION!
SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM
SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.
7

• There i approximately 1 ½” to 4 ½” of height adju tment.
• Rotate height adju t crank handle in a counter-clockwi e direction to lift the
mower deck. A clockwi e direction i u ed to lower the mower deck.
• For be t re ult , ee “SUGGESTED PRACTICE” ection. Graduated cale
are for reference only, not the actual cutter height.
• Bring tow vehicle to a complete top, hut off engine, and et parking brake.
• Di engage blade .
• Manually hut toggle witch and/or key witch to their “OFF” po ition .
• Alway remember to remove key to avoid irre pon ible u age.
• Adju t the cutting height.
• Double check vehicle to mower attachment.
• Start mower engine and et throttle to “FAST” for be t cutting performance.
• Slowly engage blade clutch lever.
• Carefully mount vehicle and tart mowing at a low travel peed.
• Swi her recommend if the tow vehicle i equipped with a mid-mount mower
to overlap the cut approximately 6”. Thi may vary depending on mowing
terrain, ob tacle , and/or tow vehicle. Alway keep SAFETY the fir t priority.
• If the tow vehicle i not equipped with a mid-mount mower, we till
recommend off etting the mower o that the tow vehicle doe not cru h the
gra .
• To change the off etting po ition both ball-lock pin hould be removed
(Figure One). The hitche will wivel around remaining bolt . Set hitche to
de ired po ition and return ball-lock pin , making ure they go thru the hitch
tubing and the emi-circled hole patterned plate .
• Remove bolt from the “L” hitch (H1), (SEE FIGURE FOUR).
• Rai e or lower hitch ection to obtain proper front to back adju tment.
• Re-in tall bolt in “L” hitch ecurely.
MOWER HEIGHT ADJUSTMENT
• Make adju tment while TrailMower i not running.
FRONT TO BACK ADJUSTMENT
For be t cutting re ult , the mowing deck hould be rai ed to ¾” higher in the
rear.
• Make adju tment while TrailMower i not running.
TOW HITCH OFFSET
Thi TrailMower ha been de igned to operate off et from the center of the tow
vehicle or con ecutively with another TrailMower, providing additional cutting width.
When off etting the mower do o to the ide oppo ite the di charge of the tow
vehicle.
STARTING TO MOW
STOPPING THE MOWING SESSION
8

SUGGESTED MOWING PRACTICES
• Operate mower engine at full throttle to a ure the be t cutting performance and
maximum material di charge.
• Allow wet gra to dry. Wet gra will clump and collect under the mowing deck.
• Mowing hould be tarted with tow vehicle in low gear and increa ed only a afe
mowing condition permit. Mowing peed hould not exceed 5 MPH.
• The average lawn hould be cut to approximately 2.5” during the cool ea on and to
over 3” during the hot month .
• For a healthier lawn and better ae thetic , your lawn hould be mowed often and
after moderate growth.
• When cutting high or den e gra area go lowly. Some area may need to be
mowed twice. The econd cut hould be at 90 degree to the fir t, if po ible.
•Mowing thick or high grass: Rai e front of deck to ½” to ¾” above rear of deck.
See “FRONT TO BACK ADJUSTMENT”. When mowing thick or high gra , it i
recommended to cut area twice. The fir t at a higher etting and the econd at the
de ired lawn height.
•Creating a manicured lawn: Never cut more than 1/3 of the gra height in one
cutting.
GENERAL TROUBLE SHOOTING
The mower i not cutting level.
•Check air pre ure of all tire ; make ure they are equal. See tire for
maximum inflation.
• Make certain blade are in talled identical, without the engine running.
The engine will not tart.
• Di engage blade , turn toggle witch to “OFF” po ition, check battery and all
other electrical connection , and in pect park plug and wire (FIGURE
THREE).
• Contact engine manufacturer or qualified mechanic.
Engine run poorly.
• See engine manual.
• Check the throttle adju ter.
• Replace fuel, clean fuel filter and fuel line.
• Check park plug and gap.
Mower bounce exce ively while towing.
• Lower tire pre ure.
• Tow at a lower peed.
IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE
MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU
ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER
PROBLEMS.
9

MOWER MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty on thi TrailMower doe not cover item that have been ubjected to
operator abu e or negligence. To receive full value from the warranty, operator mu t
maintain unit a in tructed in thi manual.
Some adju tment will need to be made periodically to maintain your unit properly.
All adju tment in thi manual hould be checked at lea t once each ea on.
BEFORE EACH USE
• Check engine oil level on a level urface. (Check twice to in ure an accurate
reading.)
• Check condition of air filter; clean and replace a nece ary.
• Check blade operation; keep blade in good condition.
• Check for loo e fa tener and tighten them a needed.
AFTER EACH USE
• Keep blade harp.
• Remove fre h gra clipping with garden ho e.
• Hardened gra clipping on under ide hould be craped out with a putty
knife.
• Keep fluid at proper level .
• Cover unit to prevent rain or other debri build-up. Definitely cover the
engine.
BEFORE AND/OR AFTER EACH SEASON
• Replace the park plug.
• Clean or replace the air filter.
• A new park plug and clean air filter a ure proper air-fuel mixture and help
your engine run better and la t longer.
• Check blade and belt for wear. Replace a nece ary.
• Change the oil.
• See engine manufacturer’ recommendation for ervicing.
STORAGE RECOMMENDATIONS
CAUTION! Do not tore engine indoor or other poorly ventilated area. Keep
engine away from ga appliance and water heater where fume could contact
open flame, pilot light , or park .
If engine is to be stored for 30 or more days, prepare unit as follows:
· Drain fuel out ide into an approved container.
· Start engine properly and run until unit i out of fuel.
· Let engine cool.
· Remove remaining ga oline from carburetor and fuel tank to prevent gum
depo it from forming within the engine. Gum depo it can cau e
malfunction in the engine.
· Store mower with blade di engaged to prevent belt from being permanently
tretched.
10

BLADE CARE AND SERVICE
For be t re ult cutter blade mu t be kept harp. The blade can be harpened with a
few troke of a file or grinding wheel. Do not attempt to harpen blade while they are
on the cutter. Disconnect spark plug wire before servicing unit.
Important: Replace blades that have been damaged or deeply nicked.
Important: Check blade and pindle hardware on a regular ba i to make ure nut
are tight.
Only a qualified mechanic should make any
adjustments, disassembly or other kind of repairs.
REPAIR PARTS
Your 44” TrailMower ha been produced with component de igned pecific to thi
machine. Although tandard V-belt , pring , bearing , blade , pulley , hardware, etc.
look imilar to part u ed on other machinery, they may in ome ca e be made of a
different con truction and/or material .
NOTES:______________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
11

FRONT
LEFT RIGHT
REAR
BALL LOCK PINS
Left off et hown
FIGURE TWO
FIGURE ONE
Slide pla tic tube nug again t
toggle witch.
(FIGURE FIVE FOR DETAILS)
12

WIRING HARNESSES
B&S ENGINE (Remote Start only) WH44CHB12V
HONDA ENGINE WH1144H
REMO E OP ION (Recoil Start) WH44RCH
PULL S AR W/ B&S ENGINE 10638
OGGLE/GROUND WIRE ASSEMBLY 9090
BLADE ENGAGE CABLE 9074
12V B&S MANUAL BLADE ENGAGE 10235
12 VOL MODELS
BA ERY (12N12A) RECOMMENDED SOLD SEPARA ELY
SOLENOID 9043
BA ERY CABLE - POSI IVE BCSR
BA ERY CABLE - NEGA IVE BCS
EX RAS
VELCRO S RAPS 7033
SWISHER DECAL OD99125
44" DECAL OD99127
IN ERLOCK MODULE MOD1
BA ERY BOX 4609 K
BA ERY PAD BA PAD
BA ERY CABLE BCL
BA ERY BOO BCB
BA ERY HOLD DOWN BHOLD
T44 RECOIL START T44 12 VOLT START
FIGURE THREE
PARTS NOT SHOWN
WIRING CONFIGURATIONS
13

FIGURE FOUR
SINGLE POINT HEIGHT ADJUST
SEE DETAILS
T-HANDLE OPTION SEE DETAIL
1
1
42
10
9
8
7
6
5
16
15
14
13
12
11
22
21
20
19
18
17
39
38
26
25
24
23
32
31
30
29
28
27
36
35
34
33
* = USE PAINT CODE:
TC=RED,G=GREEN;S=SILVER,TK=BLACK
EX: 4524RTC; 4525G
37
I EM # DESCRIP ION PAR #
1 BEL COVER 4524*
2 MO OR BASE 4517*
3 1/4 BOL NB114
4 HEIGH ADJUS ER
KNOB H7K
5/16 PAL NU NB276
5/16 PUSH NU NB117
ARM ES214
4A HEIGH ADJUS ROD 4006
5 PIVO BLOCK 4007 K
5A FLANGE BEARING 4005
6 1/2 BUSHING NB177
7 1/2 BOL NB617
7A BEARING CAP 4036 K
8 DISCHARGE CHU E 4585 K
9 ORSION SPRING 9100
10 5/16 NU NB181
11 CHU E MOUN 6030 K
12 5/16 BOL NB136
13 5/16 BOL NB596
14 CO ER PIN NB126
15 IRE/WHEEL F44157LV
16 AXLE ASSEMBLY 4040 K
17A 1/2 BOL NB588
17B 1/2 NU NB118
I EM # DESCRIP ION PAR #
18 RIGH ROLLER BRACKE 4016 K
19 AN I-SCALP ROLLER 1/2" AS003
20 1/2 NU NB121
21 5/16 BOL NB596
22 HI CH 4525 K
23 5/16 NU NB170
23A 5/16 BOL NB596
24 3/8 NU NB182
25 AN I-SCALP ROLLER 3/8" AS001
26 3/8 BOL NB575
27 HI CH UBE 4583*
28 3/8 BOL NB221
29 3/8 LOCK PIN NB520
30 FAN HI CH 4582*
31 3/8 NU NB182
32 5/16 NU NB181
33 SAFE Y HI CH PIN H11
34 5/16 BOL NB138
35 L HI CH H1 K
36 SWIVEL HI CH H10 K
BOL /NU NB145Z/NB561
37 ROLLER BRACKE 4018 K
38 DECK WELDMEN 4587*
39 LEF ROLLER BRACKE 4015 K
FRON SKIR PLA E 4518*
BACK SKIR PLA E 4519*
SKIR PLA E-BOL /NU NB596/NB170
23
23
4A3
5A
7A
23A
23
14

FIGURE FIVE
ENGINE SET-UP
FIGURE SIX
55
54
52
53
58
57
56
61
60
55
62
63
64
59
BLADE SET-UP
I EM # DESCRIP ION PAR #
40 ENGINE NO AVAILABLE
41 5/16 BOL NB253
42 5/16 NU NB170
43 OGGLE BRACKE 4483Z
44 SAFE Y E HER 6736
45 OGGLE SWI CH 685SP
46 UPPER ENG. SPACER BB105S
47 1/4 X 1 KEY S OCK 9031
48 ENG. PULLEY BB105
49 LOWER ENG. SPACER BB105SL
50 BELLEVILLE WASHER 699
51 7/16 BOL NB452N
OIL DRAIN VALVE & CAP AS122/AS123
MODULE & SCREW MOD1/NB137
I EM # DESCRIP ION PAR #
52 3/4 NU NB175
53 UPPER BELLEVILLE AS155
54 BLADE PULLEY B4104
55 HIN WASHER NB179
56 BLADE DRIVER 9018
BEARING B98
4.25" SHAF 9076
BEARING HOUSING B99EC K
57 1/4 BOL NB250
58 1/4 NU NB180
59 22" BLADE 9005
wo Blade Set 9036
60 BLADE MOUN PLA E 9008
61 3/8 NU NB216
62 3/8 BOL NB238N
63 LOWER BELLEVILLE NB607
64 3/8 BOL NB238
65A WASHER B98W
15
40
43
44
45 41
42
46
4748
49
50
51
65A

FIGURE SEVEN
65
70
68
66
67
74
73
72 69 76
75
71
77
78
79
80
83
84
82
81
86
85
FIGURE EIGHT
T-HANDLE OPTION
STANDARD ENGAGE
* = USE PAINT CODE:
TC=RED,G=GREEN;S=SLIVER,
TK=BLACK
EX: 4547C; 4578S
84
87
I EM # DESCRIP ION PAR #
65 -HANDLE LEVER 4463 K
66 CO ER PIN NB597
67 1/4 NU NB180
68 WASHER NB274
69 ENGAGE LINK 4461 K
70 CABLE CLEVIS 9023MOD
71 5/16 NU NB181
72 CLEVIS PIN NB518
73 1/4 BOL NB560
74 5/16 ORX BOL NB591
75 CONSOLE WELDMEN 4602 K
76 KEY SWI CH (12 VOL ) 3623
KEY SWI CH (Recoil Start) KSM
KEYS KSK
-HANDLE ACCESSORY KI (Recoil
Start) 4498
-HANDLE ACCESSORY KI (12V) 4607
BLADE ENGAGE DECAL OD10
ON/OFF DECAL OD99
12 VOL ON/OFF DECAL OD28
75 B CONSOLE MOUN PLA E 4601 K
5/16-18 BOL S NB138
5/16-18 NU S NB181
I EM # DESCRIP ION PAR #
77 ENGAGE S ANDOFF 4547 K
78 5/16 Spade Bolt NB260
79 1/2 BOL NB155
80 ENGAGE LEVER 4548 K
81 HANDLE KNOB B19BLACK
82 1/4 NU NB524
83 1/4 BOL NB250
84 1/2 NU NB121
85 5/16 BOL NB501
86 ENGAGE PIVO 4578 K
87 5/16 NU NB181
88 5/16 NU NB170
ON/OFF DECAL OD10
89A 5/16-18 Nut NB210Z
SEE FIG.
NINE
88
16
89A
75B
OPTION BASED ON MODEL

107
108
109
110A
110B
108
112
113
114
I EM # DESCRIP ION PAR #
107 Belt 74" 4220
108 SPRING 2SM
109 ENSION BRACKE 4593 K
110A BRAKE ASSY (LEF ) 10591
110B BRAKE ASSY (RIGH ) 10590
111 EYE BOL V139EB
112 NEU RAL SWI CH 3695
8-32 BOL /NU NB 197/NB 201
113
SWI CH BRACKE
4301 K
114 5/16 BOL /NU NB596/NB170
17
FIGURE TEN
Belt / Brake Configuration
89
90
93
94
95
97
96
98
99
91
102
96
106
105
104
103
101
100
99A FIGURE NINE
Tension Assembly
92
106A
I EM # DESCRIP ION PAR #
89 3/8 NU NB280
90 WASHER NB272
91 IDLER PULLEY B527
92 WASHER NB556
93 5/16 BOL NB254
94 IDLER SPRING 4422
95 5/16 NU NB170
96 BRAKE LINK 4532
97 3/8 BOL NB107
98 5/16 SPADE BOL NB260
99 EYE BOL V139EB
99A 5/16-18 NU NB210Z
100 3/8 NU NB182
101 IDLER BUSHING 6037
102 IDLER BRACKE 4530
103 1/4 NU NB524
104 1/4 BOL NB218
105 IDLER SPACER 6040
106 3/8 BOL NB618
106A LOCK NU NB181

Item # Description Part #
118 1/4-20 BOL NB162
119 1/4-20 NU NB524
120 BRAKE ARM 10589
121 1/4-20 NYLOCK NB180
122 BRAKE PAD 9039
123 10-24 BOL NB710
124 10-24 KEP NU NB172
125 EYE BOL V139EB
128 1/4-20 NU NB180
129 1/4-20 BOL NB102
148 1/4-20 x 2 BOL NB218
FIGURE ELEVEN
BRAKE ARM CONFIGURATIONS
18
NOTE: Part hown on thi page replace the
part which originally came on the mower.

19

OWNER’S
MANUAL
HOW TO ORDER
REPAIR PARTS:
POLARIS
44” FINISH CUT
TRAILMOWER
Each TrailMower ha it own erial number. Each engine ha
it own erial number. The erial number for the TrailMower
will be found on the right hand ide of the drive belt hou ing.
The erial number for the engine will be found on the top of the
blower fan hou ing.
All TrailMower part li ted herein may be ordered directly
from Swi her Mower & Machine Co. Inc., your neare t
Swi her dealer, or from our web ite. www. wi herinc.com
All engine part may be ordered from the neare t dealer of the
engine upplied with your mower
.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – T-44 FINISH CUT TRAILMOWER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
www. wi herinc.com
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.
MODEL NO.
POL10544C