Swisher LSEK14534 User manual

Read and follow all Safety
Precautions and Instructions
before operating this
equipment.
LOG
SPLITTER
OWNER’S
MANUAL
1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093
PHONE [phone] TOLL FREE 800-222-8183 FAX [phone]
MODEL NO.
LSEK14534
LSEK14534-CA
STARTING SERIAL #:
L114-196001
Manufacturing quality lawn care equipment since 1945
Safety
Assembly
Operation
Service and Adjustment
Repair Parts
Made In The
USA
IMPORTANT
swisherinc.com
19199
REV 14-196

2
LIMITED WARRANTY
TABLE OF CONTENTS
WARRANTY………………....….2
SAFETY..……………………….3-4
TOWING..….……..……………..5
OPERATION……………………6-8
MAINTENANCE.……………….8
DECALS…..………….……………….9
PARTS BREAKDOWN…………….10-15
WIRING……………………………...15
TROUBLESHOOTING……………...16
SPECIFICATIONS..…………………18
The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in
materials and workmanship for the period's shown below beginning from the date of purchase by the original
consumer purchaser.
As required by CFR § 1060.120, the fuel system related components, which have been certified to this
equipment by SAI are to be free of defects in material and workmanship for a period of two (2) years from the
date of purchase by the original consumer purchaser.
We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This
warranty is subject to the following limitations and exclusions:
Engine Warranty All engines utilized on our products have a separate warranty extended
to them by the individual engine manufacturer. Any engine service
difficulty is the responsibility of the engine manufacturer and in no
way is Swisher, or its agents responsible for the engine warranty. Engine
warranty and contact information is as shown in the engine owners manual.
Hydraulic System 1 Year
Materials and Workmanship 3 Years
Limitation This warranty applies only to products which have been properly
assembled, adjusted, and operated in accordance with the instructions
contained within this manual. This warranty does not apply to any
product of Swisher that has been subject to alteration, misuse, abuse,
improper assembly or installation, shipping damage or to normal wear of
product.
Exclusions Excluded from this warranty are normal wear items, normal or routine
adjustments, and normal or routine maintenance.
In the event you have a claim under this warranty, you must return the product to an authorized service dealer.
All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or
repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this
warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase,
and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any
warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS
STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of
consequential damages or limitations on how long an implied warranty may last, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights,
which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

SAFETY PRECAUTIONS
WARNING: The engine exhaust from this product contains chemicals known to the state of California to
cause cancer, birth defects or other reproductive harm.
DANGER: Your log splitter was built to be operated according to
the rules for safe operation in this manual.
As with any type of power equipment, carelessness or error on the part of the operator can result in serious
injury. If you violate any of these rules, you may cause serious injury to yourself or others.
•Read and understand the manual. Learn to operate this equipment in a safe manner. Familiarize
yourself with all of the controls in a safe environment before starting to work with this machine.
•DO NOT under any circumstances alter this log splitter. This equipment was designed and
engineered in accordance with operating instructions. Altering this equipment, or using this
equipment in such a way as to circumvent its design capabilities and capacities, could result in
serious injury or fatality and WILL VOID THE WARRANTY.
•Allow ONLY responsible adults who have read this manual to operate this machine. NEVER allow
children to operate this machine.
•NEVER operate or allow someone to operate this equipment while under the influence of alcohol,
drugs or medication. Being coherent is essential for safety.
•ALWAYS use outdoors with adequate ventilation. DON’T run the engine in an enclosed area.
Exhaust gases contain carbon monoxide. This odorless gas can be deadly when inhaled.
•NEVER use splitter for any other purpose than splitting wood. Any other use can result in injury.
Your splitter is a precision piece of power equipment, not a toy. Therefore, exercise extreme caution
at all times.
•ONLY a single operator is to load and operate the log splitter. KEEP all others, including pets and
children, a minimum of 20 feet away from your work area. More accidents occur when more than
one person operates the log splitter than any other time.
•ALWAYS wear protective gear such as safety goggles, protective hearing device, steel-toed shoes,
and tight-fitting gloves without drawstrings or loose cuffs.
•NEVER wear loose clothing or jewelry that can be caught by moving parts of the splitter and pull
you into it. Keep hair away from moving parts.
•NEVER operate your splitter on wet, muddy, or icy surfaces. KEEP work area clean of split wood.
Safe footing is essential in preventing accidents.
•ONLY operate splitter on level ground with wheels blocked, not on the side of a hill. It could tip, or
rolling logs, poor footing, etc. could cause an accident.
This Safety Alert Symbol indicates important messages in this manual.
When you see this symbol, carefully read the message that follows and be
alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands, feet, and throw objects.
Failure to observe the following safety instructions could result in serious injury or death.
3

4
•
NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can
explode.
•NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling.
•This unit is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is
equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used it
should be maintained in effective working order by the operator.
-NOTE-
In the state of California, the above is required by law (Section 442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on feder
al lands. A spark arrester muffler (optional by
manufacturer) is available at your nearest engine dealer. Check legal requirements in your area.
•ONLY use your hands to operate the control lever. NEVER use foot, knee, rope or any extension device.
•Split ONLY one log at a time. NEVER attempt to split two logs on top of each other.
•NEVER place hands or feet between log and splitting wedge or between log and buttplate during forward
or reverse stroke. ALWAYS keep fingers clear of splits that open in log during splitting operation.
•DO NOT straddle or reach across the splitting area while operating the splitter.
•DO NOT step over splitter when the engine is running. You may trip or accidentally activate the splitting
wedge. Walk around to get to the other side.
•
NEVER attempt to load splitter while splitting wedge is in motion. When loading log splitter, place hands
on the sides of the log, not the ends.
•NEVER attempt to split woods across the grain. Wood may burst or fly out of your splitter and result in
serious injury.
•NEVER leave your splitter unattended with the engine running. Shut off the engine if you are leaving
your splitter, even for a short period of time. Someone could accidentally activate the ram and be injured.
•Both ends of the log sh
ould be cut as squarely as possible to prevent the log from sliding out of the splitter
during operation. Log length should be kept to 24” or less.
•NEVER operate your splitter while it is attached to the tow vehicle.
•BEFORE towing, be certain that the splitter is securely attached to the towing vehicle and that the support
leg, beam, 4-way wedge and cylinder are secured in there respective towing positions.
•DO NOT loosen or remove any hydraulic fitting, line or reservoir cap while your splitter or engine is
running.
•Fluid escaping from a very small hole can almost be invisible. DO NOT check for leaks with your hand.
See maintenance section for instructions. IF injured by escaping fluid, see a doctor at once. Serious
infection or reaction can develop if proper medical treatment is not administered immediately.
•DO NOT operate your splitter in poor mechanical condition or when it is need of repair.
•ALWAYS disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to
prevent accidental starting the engine when setting up, transporting, adjusting or repairing.

TOWING SAFETY
•Do not allow persons to ride on splitter. Do not carry any cargo or wood on your
splitter. It may fall off and endanger vehicles that are following you.
•Be sure support leg is in the travel position and coupling secure. This must also be
retracted so as not to interfere while towing. Retract support leg by removing pin,
pivoting up, and replacing pin.
•Never exceed 45 MPH while towing your splitter. Be extra cautious when traveling
over rough terrain, especially over railroad tracks.
•Always be careful while backing your splitter. You could jackknife your log splitter
if not careful.
•Before using splitter, disconnect it from tow vehicle. A log could easily be pushed
forward into the vehicle.
•See proper inflation instructions on side of tires.
•Be aware of the extra length of splitter while turning, parking, crossing intersections,
and in all driving situations.
5
OPERATION INSTRUCTIONS
POSI-LOCK COUPLER
ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE. PLACE HANDLE IN LOCKED
POSITION WITH BALL IN COUPLER. TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT
COUPLER IS NOT LOOSE ON BALL. CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE
RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE.
TO OPEN, PULL UP ON COUPLER HANDLE AND ROTATE FORWARD. PLACE COUPLER ON BALL
WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET, ROTATE COUPLER HANDLE
BACKWARD UNTIL HANDLE IS IN LOCKED POSITION.
AFTER TOWING FOR 50 MILES, CHECK COUPLER FOR TIGHTNESS ON BALL. ALWAYS CHECK
TIGHTNESS BEFORE TOWING. BE SURE COUPLER HANDLE IS IN LOCKED POSITION.
WARNING:
NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS. ALWAYS USE
CORRECT BALL SIZE, MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER. LOCK
COUPLER HANDLE SECURELY BEFORE TOWING. ALWAYS CHECK FOR DAMAGES AND
REPLACE IF DAMAGED. AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING.

6
ASSEMBLY
This log splitter has been partially assembled at the factory. Refer to the drawings and part lists should it become
necessary to disassemble the unit for repair or replacement of parts.
Inspect all components for damage. If you believe you have a damaged part please contact customer service
immediately at 1-800-222-8183.
WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling
equipment should be used.
Refer to uncrating and assembly instructions for assembly procedures.
OPERATION
INTENDED USE: This log splitter is intended and designed to only split wood. NEVER use for any other
purposes. Doing so can cause injury or VOID THE WARRANTY.
IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After assembly, see separate
Engine Manual for proper fuel and oil recommendations.
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND
HYDRAULIC RESERVOIR.
FILLING THE HYDRAULIC RESERVOIR
Fill the hydraulic reservoir to the top mark on the dipstick or, depending on your Log Splitter model, to the lower fill
line of the reservoir with DexronIII / Merconautomatic transmission fluid, 10W AW hydraulic fluid or Pro-Mix
AW-32 Hydraulic oil. After the hydraulic reservoir and the engine crankcase are filled correctly with their respective
oils, set the throttle and turn on the fuel shut-off valve. Disengage pump via cold weather clutch (pull clutch handle
outward until secured in slot). Once engine is started then engage the pump system by pushing in the cold weather
clutch handle. The hydraulic pump should prime itself. With the engine running, move the hydraulic valve lever
toward the wedge. This will cause the cylinder to extend and expel air. When the cyl
inder is fully extended, retract it.
Repeat this procedure several times. (An erratic movement of the cylinder and wedge indicates that there is air in the
system). Once the cylinder has a smooth and constant speed indicating that all air has been expelled, shut the system
off and refill the reservoir until the fluid is in the safe operating range as specified by the marks on the dipstick.
START UP
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE
AND HYDRAULIC RESERVOIR.
See separate Engine Manual for fuel and oil recommendations. Your log splitter has come equipped with a fuel shut-
off valve for towing purposes.
Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been used. The engine
will only start when the throttle lever and fuel shut-off valve are turned to their ON positions.
STARTING INSTRUCTIONS
Note: The engine may be equipped with an integrated automatic choking system.
1. Move throttle control to “FAST.”
2. Turn ignition key to the “ON” position to start engine.
3. If Engine is equipped with manual choke lever, pull choke lever out. (Depending on current conditions unit
may not need to be choked).
4. When engine starts, leave throttle control at “FAST.” The throttle must be set in the fast position for
maximum performance.
5. To stop engine, move throttle lever to “SLOW” for a few seconds then turn the ignition key to the “OFF”
position.
IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of
California Public Resource Code Section 4442 to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land. Other states or federal areas may have similar laws.

COLD WEATHER START UP
The Cold Weather Clutch enables the engine to be started without having to pull through cold, thickened
hydraulic fluid. Simply pull the handle out to the locked position. Start engine, let it warm up, and push in
the Cold Weather Clutch handle to engage pump system. If the engine is left running for extended period
of time (5 minutes or longer) without splitting wood disengage the pump drive system via Cold Weather
Clutch to reduce the load of the engine. This will save fuel and stop the pump which can reduce hydraulic
oil temperature and extend oil life.
4-WAY WEDGE OPERATION: See 18851 Owners Manual in parts bag.
SPLITTER OPERATION
1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should always
be on the lower side of the log splitter.
2.
Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate and up against
the beam.
3. Depress the valve lever so that the cylinder will drive the wedge into the log. Extend the cylinder until the
log splits or to the end of its stroke. If the log has not completely split after the cylinder has reached the end
of its extension, retract the cylinder, reposition log and repeat process. NOTE: Leaving the valve in the
“actuate” position at the end of the stroke may damage the pump. Always use extra care when splitting logs
with ends that are not square.
NOTE: To extend the life of the hydraulic cylinder, avoid “BOTTOMING OUT” the cylinder.
4. When using the Log Splitter in the vertical position, make sure the beam latch is engaged as shown below.
Pull the bent pin outward then twist and release it to hold the I-beam in place.
TOWING SAFETY
This unit should not be towed on any street, highway, or public road without checking the existing federal, local, and
state laws. Any licensing or modifications such as taillights, etc., need to comply with existing federal, local, or state
vehicle requirements is the sole responsibility of the purchaser. Obey all regulations when towing on public roads
and highways. See also SAFETY PRECAUTIONS.
*Turn the fuel shut-off valve OFF to prevent flooding of the engine while traveling.
*Ensure that 4-way wedge is placed securely in the towing position, fastened to the motorbase or in
the towing vehicle.
*Be careful when backing up. You can easily jack-knife your splitter.
TOWING AT NIGHT
The requirements for taillights are based on States regulations. Some states allow towing at night as long
as the towed equipment does not visibly impair the tow vehicle taillights. This is based on a state, to state
requirements. The customer is responsible for meeting the states requirements.
If a “Statement of Origin” is required in your state, see your local dealer to receive one.
HYDRAULIC SAFETY
The hydraulic system on your splitter requires careful inspection along with the mechanical parts. Be sure to replace
any frayed, kinked, cracked or otherwise damaged hydraulic components. Just because it isn’t leaking today doesn’t
mean that it will not fail tomorrow.
7

8
MAINTENANCE AND STORAGE
WARNING: DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE.
Consult the operating and maintenance instructions of the engine manufacturer for engine care.
Always check the oil level of the hydraulic reservoir before operation. Operating without an adequate oil
supply will cause severe damage to the pump. Change the hydraulic fluid in the reservoir after every 100 hours of
operation. Change the hydraulic filter after every 50 hours of operation (use only a 10 micron hydraulic filter).
Periodically check that all nuts, bolts, screws, clamps and fittings are tight and secure.
To keep your splitter in top working condition perform all recommended maintenance procedures before you use
your splitter.
If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it.
Completely drain the fuel tank prior to storage. Always store gasoline in an approved, tightly sealed container. Store
container in a dry, cool place with adequate ventilation. Keep fuel away from areas where fumes could contact open
flame, pilot light or sparks.
Be aware of the environment when disposing of used petroleum products. Please dispose of used hydraulic
fluid, engine oil and any by products from the maintenance of your splitter at approved recycling centers.
Should it become necessary to disassemble the unit for repair or replacement of parts, refer to the drawings and parts
list on the following pages. Exercise extreme caution, as some parts are very heavy and will require sufficient
persons or mechanical handling equipment.
Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although
standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases
be made of a different construction and/or materials. All replacement parts must meet manufacturer’s
specifications.
The operation of any splitter can produce foreign objects which can be thrown
into the eyes, resulting in severe eye damage. Always wear certified safety
glasses or wide-vision safety goggles over spectacles before staring any
splitting machine and while operating such a machine.
The operation of any splitter produces sound waves that are damaging to the
human ear. Ear protection is recommended.
*Fluid escaping from a very small hole can almost be invisible. Do not check for leaks with your hand. Escaping
fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard or wood over the suspected leak and looking for
discoloration. IF injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if
proper medical treatment is not administered immediately.
*Should it become necessary to loosen or remove any hydraulic fittings, lines or reservoir cap, be sure to relieve
all pressure by shutting off the engine and moving the control handle back and forth several times.
*NEVER remove the cap from the hydraulic tank or reservoir while the unit is running. Hot oil under pressure
could result in serious injury. See also SAFETY PRECAUTIONS.
The pressure relief valve on your splitter is preset at the factory. DO NOT adjust the valve. Only a
qualified technician should perform this adjustment.
*NEVER run the log splitter for extended periods of time without cycling the cylinder. Running the unit
without cycling hydraulic fluid throughout the entire system will cause excessive heat build up in all
components.

12494 – HYDRAULIC FILL PLUG
DECAL
11427 – DANGER DECAL
12492 – OPERATOR INSTRUCTION
DECAL
OD16 – FUEL SHUT OFF DECAL 12493 – COLD WEATHER DECAL
SAFETY DECALS
Replace decals immediately if damaged.
9
12549 – DO NOT EXCEED 45 MPH
DECAL
12532 – HYDRAULIC OIL DECAL

ASSEMBLY DETAIL
10
Item # Part # Description Item # Part # Description
1 7296K Tire/Wheel, Log Splitter; Blk 1 10548 Bolt - Serr Flange, 5/16-18X1GR5 ZY
2 NB179 Washer - 3/4 ID X 1 1/4 OD 18 GA ZY 2 BRS6 Spring - Idler Arm
3 2203CN Nut - Castle 3/4-16, .625 Tall, Grade 2 3 19174TK Lever Arm - Engage, LS; Txt Blk
4 NB633 Pin - Cotter, 1/8 X 2(Ext Prng Crbn Stl) 4 NB181 Nut - Nyloc 5/16-18 ZY
5 2203DC Cover - Dust, Wheel Hub 5 6040Z Washer - Idler, ZP
6 NB151 Bolt - 1/2-13 X 6 HCC GR5 ZP 6 NB107 Bolt - 3/8-16 X 1 1/2 HCC GR5 ZY
7 NB555 Washer - USS Flat, 1/2 ZY 7 19173TK Arm- Idler, LS; Txt Blk
8 NB688 Nut - Nyloc Jam, 1/2-13 ZY 8 14424 Pulley - Backside Idler
9 18839TK Weldment - Wedge, 4-Way; Txt Blk 9 NB272 Washer - SAE Flat 3/8 ZY Carbon Steel
10 NB587 Bolt - Carriage, 5/16-18 X 1 3/4 ZY Gr 2 10 6037 Bushing - Idler
11 2030 Knob - Black Plastic 11 2077 Pivot - Handle Grip
12 19177TK Weldment - Motorbase, LS; Txt Blk 12 B527 Pulley - Idler, OD3.25" ID3/8"
13 12441 Grommet - PVC 1.75ID X 2.375OD, 2GD 11GA 13 NB182 Nut - Nyloc 3/8-16 ZY
NOTSHOWN 12363 Hose - Hydraulic, 3/4"ID X 72" 14 NB221 Bolt - 3/8-16 X 2 1/2 HCC GR5 ZY
NOTSHOWN 19165 Hose - Hydraulic Pressure, 60" NOT SHOWN 6046HP Belt - V, 47" High Power
ASSEMBLY DETAIL IDLER DETAIL
IDLER DETAIL
IDLER DETAIL

11
BELT ROUTING DIAGRAM
(VIEWED FROM UNDERSIDE OF LOG SPLITTER )
PUMP PULLEY #19163
ENGINE PULLEY #19164
IDLER PULLEY # 14424
FILTER DETAIL
PUMP DETAIL
Item # Part # Description
1 LS1112 Head - Filter (FPC3012NXXR4X)
2 LS1113 Filter - Element
3 7329 Fitting - Line Return (4501-12-12) YZ
Item # Part # Description
1 19163 Pulley - Pump 5/8" ID x 4" OD
2 NB596 Bolt - Serr Flange, 5/16-18 X3/4 Gr 5
3 9030 Key Stock - 3/16 X1 Under Size Pln Fnsh
4 NB182 Nut - Nyloc 3/8-16 ZY
5 19167TK Mount - Pump, LS; Txt Blk
6 NB170 Nut - Serr Flange 5/16-18 ZY Case Hrd
7 19166 Pump - Hydraulic, 22 GPM
8 NB618 Bolt - 3/8-16 X1 1/4 GR5 ZY
9 19175 Fitting - Hydraulic Input 1" BARB 1" NPT
10 LS4999 Clamp - Hose No. 16 (1 1/16" X2")
11 19171 Hose - Hydraulic Suction, 2.75"
12 NB312 Screw - Set 5/16-18 X1/2 With Loctite H
BELT PART # 19198
IDLER PULLEY # B527

12
Item # Part # Description
1 NB643 Bolt - Carriage 1/2-13 X2 1/2 GR5 ST ZY
2 7233TK Wedge - Painted
3 7237TK Spacer - 4 Slot .500 Thick -Txt Blk
4 7388TK Spacer - 4 Slot, Textured Black 11GA
5 7333TK Plate - Bottom Head Slide, Painted
6 NB555 Washer - USS Flat, 1/2 ZY
7 NB508 Washer - Lock, 1/2 ZY Medium Duty
8 NB213Z Nut - 1/2-13 GR2 ZY
WEDGE DETAIL
Item # Part # Description
1 19581TK Weldment - Beam, LSEK14534; Txt Blk
2 7288TK Line - Asy Stationary, Splitter; Txt Blk
3 7291 Elbow - Hydraulic (2501-8-8) YZ
4 7355TK Cylinder - 5 X24 X2 Painted
5 7293 Pin - Cylinder to Beam Zp
6 NB642 Cotter - Hairpin #23-09 .093 X1-13/16
7 7292 Pipe - Nipple (5404-8-8) ZY
8 NB121 Nut - Jam Lock, 1/2-13 2-Way Gr A
9 NB555 Washer - USS Flat, 1/2 ZY
10 12669 Bolt - 1/2-13 X3 1/4 GR8 Alloy ZY
11 7329 Fitting - Line Return (4501-12-12) YZ
12 7287TK Valve - Control; Splitter, Painted
13 19699 Fitting - Hydraulic 3/4" ML 1/2" FML NPT
14 19578TK Spacer - Log Stripper; Txt Blk
15 NB108 Bolt - 1/2-13 X7 HCC GR5 ZP
16 NB779 Nut - Serr Flange, Hex ZY 3/8-16
17 NB780 Bolt - Serr Flange, ZY 3/8-16X3/4 Gr5
18 19579TK Weldment - Log Table; Txt Blk
BEAM DETAIL

13
TONGUE DETAIL
Item # Part # Description
1 19565TK Cover - Fuel tank, Txt Blk
2 18225 Bracket - Fuel Tank
3 26X249 Screw - .312-18 X .75
4 18214 Fuel Tank - 2.5 Gallon, Carb, W/O Cap
5 18221 Cap, Fuel - 2.50 Gallon, Carb Sealed
6 NB180 Nut - Nyloc 1/4-20
7 NB274 Washer - SAE Flat 1/4 ZY
8 12379 Breather Cap W/Dipstick
NOT SHOWN 18223
Clamp - Fuel Line 13/32 OD, 3/16 ID Tube
NOT SHOWN 6FLC
Clamp - Fuel Line Hose; 1/2"OD .092 Diam
NOT SHOWN 11782 Line - Fuel, Bulk; 1/4" LowPerm
NOT SHOWN 18232 Line - Fuel, Bulk; 3/16" Low Perm
FUEL DETAIL
Item # Part # Description
1 NB649 Bolt - 3/8-16 X3 1/2 GR5 ZY
2 NB272 Washer - SAE Flat 3/8 ZY Carbon Steel
3 NB182 Nut - Nyloc 3/8-16 ZY
4 19183TK Weldment - Tongue, LS; Txt Blk
5 10177 Washer - Fender 3/8 X1.5, Crbn Stl GR 2
6 NB150 Bolt - 3/8-16 X3 HCC GR5 ZY
7 NB126 Pin - Cotter, 1/8 X1, Crbn Stl Ext Prng
8 NB177 Washer - Mach 1/2 NR 14 GA
9 12364 Spring - Compression .620ID X2" ZP
10 12345 Pin - Beam Lock 1/2 X3
11 19477TK Plate - Support, Kickstand Txt Blk
12 12447 Ubolt - SQ , 3/8-16X2.437 X3 Lg GR 5 ZY
13 19179 Jackstand
14 7366 Chain - Safety, W/S Hook Zp
15 7365 Coupler - 2" Ball

14
ENGINE DETAIL
BEAM LATCH DETAIL
ITEM # PART # DESCRIPTION
1 18821 Pin - Beam Latch
2 18822 Spring - Compression
3 18823 Washer - Flat, 1/2"
4 NB126 Pin - Cotter
Item # Part # Description
1 N/A Engine - KAW 14.5HP, LS
2 NB711 Washer - Split Lock, 3/8 ZY, Medium
3 NB618 Bolt - 3/8-16 X1 1/4 GR5 ZY
4 689S Spacer - Short, Engine Pulley, .687
5 19164 Pulley - Engine 1" X4.5" OD
6 9031 Key Stock - 1/4 X1 Undr Sz Plain Fin
7 689L Spacer - Long, Engine Pulley, 1.5"
8 10291 Washer - Bellville, .512x1.26x .138 GR2
9 NB452N Bolt - 7/16-20 X1 HCF GR5 ZP Nyloc
10 19181 Muffler - KAW 14.5HP, LS
11 26X249 Screw - .312-18 X.75
12 TR150W Washer - .531IDX1 1/2ODX.062(Ht Trtd)ZY
NOT SHOWN 16000 Valve - Oil Drain
NOT SHOWN 18810 Adapter - Oil Drain, Kawasaki
NOT SHOWN 7414 Valve - Fuel Shut Off (Inline)
NOT SHOWN N/A Muffler Mounting Bolt(Comes with Engine)
NOT SHOWN N/A Muffler Mounting Washer(Comes with Engine)
NOT SHOWN N/A Exhaust Gasket(Comes with Engine)
ITEM # PART # DESCRIPTION
1 024900 Nut - 10-24 Nylon Lock
2 17127 Bracket - Carbon Canister
3 024203 Bolt - 10-24 X 3/4 Phil Truss Head
4 18224 Carbon Canister
5 18219 Cable Tie
NOTSHOWN 18232 Line - Fuel, Bulk; 3/16" LowPerm
CARBON CANISTER DETAIL
(CA MODELS ONLY)

15
12 VOLT ACCESORIES
Item # Part # Description
1 19566TK Plate - Right Side, Console; Txt Blk
2 19569TK Plate - Rear, Console; Txt Blk
3 19567TK Plate - Left Side, Console; Txt Blk
4 19568TK Plate - Top, Console; Txt Blk
5 26X249 Screw- .312-18 X .75
6 024206 Screw- 12 X 1/2 HexSelf Tap
7 NB161 Screw- HX Tek 1/4 X 3/4 ZP
8 1002004 Solenoid - 3 Pole
9 19170 Cable - Choke 52"
10 9087 Nut - Key Switch
11 9088 Washer - Lock, Key Switch
12 NB711 Washer - Split Lock, 3/8 ZY, Medium
13 NB456 Nut - 3/8-24 HNF ZY Gr 2
14 3623 Switch - Key
15 26X263 Screw- Hex.25-20X0.59
16 686K Knob - Throttle, For 686
17 19169 Cable - Throttle 52"
18 19691TK Weldment - Battery Hold Down, Txt Blk
19 NB524 Nut - Serr Flange, 1/4-20 Grade 5 ZY
20 NB690 Bolt - Serr Flange, 1/4-20 X 3/4 GR5 ZY
21 AS013 Strap - Tarp, 9"
22 NB180 Nut - Nyloc 1/4-20
23 26X229 Screw- 1/4-14X.38" ST
24 NB274 Washer - SAE Flat 1/4 ZY
25 NB180 Nut - Nyloc 1/4-20
26 NB551 Bolt - 1/4-20 X 4 HTC GR2 ZP
27 BATPAD Pad - Battery
28 NB524 Nut - Serr Flange, 1/4-20 Grade 5 ZY
NOT SHOWN AS084 Electrical - 5 Amp Fuse
NOTSHOWN 19187 Harness - Wiring, LSEK14534
NOTSHOWN BC24 Cable - Battery, 24" Red
NOTSHOWN BCBT Boot - Rubber, Small, Battery Cable
NOTSHOWN BCS Cable - Battery, 10" Black
NOTSHOWN BCSR Cable - Battery, 10" Red
Wiring Diagram
BATTERY
LARGE
RED
RED
LARGE
RED
RED
GREEN
5 AMP
FUSE
IGNITION
SWITCH
ENGINE
SOLENOID
BLACK
GREY
WHITE
LARGE
BLACK
STARTER
S
M
LG
B

16
TROUBLESHOOTING
NOTE: For repairs beyond those listed here, contact your nearest authorized service center.
* Flushing the reservoir tank and hoses with kerosene whenever service is performed on the tank, hydraulic pump or
valve is recommended. Contact an authorized service center.
Problem Cause Remedy
Engine fails to start. 1. Spark plug wire disconnected. 1. Connect wire to spark plug.
2. Fuel tank not full enough or stale fuel. 2. Fill tank full with clean, fresh gasoline.
3. Throttle control lever not in correct
starting position. 3. Move throttle lever to FAST position.
4. Fuel valve not ON or blocked fuel line. 4. Turn on fuel valve or clean fuel line.
5. Faulty spark plug. 5. Clean, adjust gap, or replace spark plug.
Engine is hard to start or runs erratically. 1. Spark plug wire loose. 1. Connect and tighten spark plug wire.
2. Blocked fuel line or stale fuel. 2. Clean fuel line; fill tank with clean, fresh
gasoline
3. Water or dirt in fuel system. 3. Drain fuel tank. Refill with fresh gasoline.
4. Dirty air cleaner. 4. Clean or replace air cleaner.
5. Carburetor out of adjustment. 5. See authorized service center.
Cylinder rod will not extend or contract. 1. Cold weather clutch not engaged. 1. Engage cold weather clutch.
2. Broken or improperly installed belt. 2. Replace or reinstall belt.
3. Low hydraulic fluid. 3. Fill hydraulic tank to correct fluid level.
4. Hydraulic lines blocked. 4. Flush and clean hydrualic system.*
5. Damaged or broken pump. 5. See authorized service center.
6. Damaged control valve. 6. See authorized service center.
Cylinder rod is slow or erratic while
extending and contracting. 1. Low hydraulic fluid. 1. Fill hydraulic tank to correct fluid level.
2. Contaminated hydraulic fluid. 2. Drain fluid, flush system, and refill.
3. Excessive pump inlet vacuum. 3. Make certain pump hoses are clear and
unblocked. Make certain hose is not
collapsing under suction.
4. Damaged pump. 4. See authorized service center.
5. Damaged control valve. 5. See authorized service center.
6. Internal cylinder damage. 6. See authorized service center.
Cylinder is leaking. 1. Broken seals. 1. See authorized service center.
2. Scored cylinder. 2. See authorized service center.
Engine will not turn over. 1. Weak or dead battery. 1. Recharge or replace battery.
2. Blown fuse. 2. Replace fuse.
3. Corroded battery terminals. 3. Clean battery terminals.
4. Loose or damaged wiring. 4. Check all wiring.
5. Faulty ignition switch. 5. Check/replace ignition switch.
6. Faulty solenoid. 6. Check/replace solenoid.
Engine clicks but will not start. 1. Weak or dead battery. 1. Recharge or replace battery.
2. Corroded battery terminals. 2. Clean battery terminals.
3. Loose or damaged wiring. 3. Check all wiring.
4. Faulty solenoid. 4. Check/replace solenoid.
Battery will not charge. 1. Bad battery. 1. Replace battery.
2. Corroded battery terminals. 2. Clean battery terminals.
3. Faulty solenoid. 3. Check/replace solenoid.
4. Bad alternator. 4. See authorized service center.

17
MAINTENANCE LOG
NotesService PerformedDate of Service

NOTES:
18
SPECIFICATIONS
Splitting Force 34 Tons*
Engine 14.5 HP Kawasaki, 603CC
Battery 12VType U1L (not included)
Splitting Positions Horizontal and Vertical
Cylinder Size 5" X24"
Pump 2 Stage with Heavy Duty Bearings
Pump Specs 22 Gallons Per Minute
Valve Auto Return
Drive System Belt Drive 1:1 Ratio with Clutch for
Easy Starting
Hydraulic System Fluid
Capacity
15 Gallons
(13.5-14 Gallons required for
normal operation)
Maximum Log Length 25 1/2"
Tire Specs 4.00 X 4.80 X 8 with High Speed
Bearings
Ball Hitch 2" Ball
Unit Weight 751 Lbs
*Splitting force rating is consistent with the current industry standard for calculation.

19
SWISHER HISTORY
Back before electricity came to rural Missouri Max Swisher was producing lawn mowers
from his mother’s chicken house. Max never liked to mow grass. He installed a
gearbox on his family’s lawn mower creating a self-propelled unit. By tying one end of a
rope to the mower and the other end to a tree in the center of the yard the mower
circled the tree, shortening the rope and guiding the mower in concentric circles. Max
enjoyed relaxing under a shade tree while his invention did all the work.
Max had designed his first self-propelled rotary lawn mower to do his dirty work for him.
Neighbors noticed his new invention and began asking him to make more. Today, over
65 years later, Swisher is still producing innovative lawn and garden and ATV/UTV
equipment designed to give us all more “relaxing in the shade” time.
Swisher products have been featured nationally on television programs such as Regis
and Kathie Lee and seen in publications like ATV Magazine, Country Journal, Popular
Mechanics Magazine and others. In January 2000 Popular Mechanics Magazine
named Max’s zero turning radius riding mower one of the 20th century’s top household
inventions.
Swisher offers value and function in its products to meet your grounds maintenance
needs. CELEBRATING OVER 65 YEARS OF INNOVATION
SINCE 1945

OWNER’S
MANUAL
MODEL NO.
LSEK14534
LSEK14534-CA
HOW TO ORDER
REPAIR PARTS:
LOG SPLITTER
Each Log Splitter has its own serial number. Each engine has
its own serial number. The serial number for the Log Splitter
will be found on the right hand side of the hydraulic oil
reservoir. The serial number for the engine will be found on
the top of the blower fan housing.
All Log Splitter parts listed herein may be ordered directly
from Swisher, your nearest Swisher dealer, or from our
website.
All engine parts may be ordered from the nearest dealer of the
engine supplied with your log splitter. Parts subject to change
without notice.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – SWISHER LOG SPLITTER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
www.swisherinc.com
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER
1602 CORPORATE DRIVE
WARRENSBURG MO 64093
CHANGING YOUR LANDSCAPE SINCE 1945
swisherinc.com