Sygonix 1898921 RSL 433 MHz User manual

App Instruction Manual
Sygonix Gateway
Item No. 1898921 / RSL / 433 MHz
Item No. 1898922 / RS2W / 868 MHz
www.conradconnect.de
1898921_1898922_v1_0719_02_jh_m_app_en_1080x1920px_(8)

Contents
Introduction
General Information
Important Information
Conrad Connect
Legal Notice
Requirements
Network Connection
Security
Subnetting
Mobile App
Get started
Installation/Deinstallation
Install the App
Notes on Deinstallation
User Account
Create a User Account
Log in
Switch Accounts
Manage your Account
Home Page
Main Controls

Gateway
Add a Gateway
Open the Gateway Dashboard
Open the Device Menu
Control
Manual Control
Globally Control End-node Devices
Set a Timer
Schedules
Control Log
Manage Gateways
Rename a Gateway
Replace a Gateway
Delete a Gateway
Add a Gateway to Another Account
Add an End-Node Device
Add a 433 MHz device
Add a 868 MHz device
End-Node Device
Open the Device Menu
Device Control
Manual Control
Timed Control
Set a Timer
Schedules
Rules
How rules work
Manage one-action rules

Manage scheduled rules
Control Log
View Log
Clear Log
Manage Devices
Rename a Device
Relearn a Device
Delete a Device
Data Charts
View chart
Troubleshooting
Ghost triggers
Resetting a device
Pair type 1 – 433 MHz
Pair type 2 – 868 MHz
Pair type 3 – 868 MHz
Pair type 4 – 868 MHz

Introduction
You build your smart network by using at least
one gateway as a controller, and register end-
node devices such as sensors, power meters,
and actuators (e.g. motor) on the gateway.
The mobile app allows you to control and
manage all devices in your smart network.
General Information
Important Information
Observe information in a red frame to
avoid harming yourself or others, and
prevent product damage.
Give information in an orange frame special
attention.
The blue frame provides tips on product use
and features.

Conrad Connect
www.conradconnect.de
Your product is compatible with the Conrad
Connect IoT platform.
Device integration with Conrad Connect
requires a Conrad Connect Account.
You can set up an account at the given URL.
Legal Notice
This is a publication by Conrad Electronic SE,
Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved.
Reproduction by any method, e.g. photocopy,
microlming, or the capture in electronic data
processing systems require the prior written
approval by the editor. Reprinting, also in part,
is prohibited. This publication represents the
technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.

Requirements
Network Connection
Security
It is strongly recommended that you set up your
WiFi Router/WiFi Access Point (AP) to use the
most secure encryption option it supports.
Subnetting
If you subnetted your network, the mobile
device running the app and the devices of your
smart network must be hosts on the same
subnet.

Mobile App
Through the mobile app you manage gateways
and end-node devices linked to them.
Get started
As a rst time user follow the below steps:
1. Install the App.
2. Create a User Account.
3. Log in.
4. Learn how to manage your account:
-Go to Manage your Account
5. Learn how to add a gateway and manage it:
-Go to Gateway
6. Learn how to add end-node devices and
manage them:
-Go to Add an End-Node Device and End-
Node Device

Installation/Deinstallation
Install the App
Apps are available for Android and iOS mobile
devices.
Head to the respective app store and download
the app named 'Sygonix RSL RS2W' onto your
mobile device.
Make sure your mobile device satises the
minimum requirements as outlined on the
app store download page.
Notes on Deinstallation
When you uninstall the app, the settings are
retained.
Settings become available again as soon as
you re-install the app and log in with the same
account.

User Account
Account settings are stored under your account
in the cloud.
Create a User Account
A user account is required for you to operate
the device.
1. Open the app.
2. Touch Register account.
3. Enter the requested details into the
registration form and conrm with Submit.
4. A new account will be set up for you.
Wait until you receive the conrmation for
successful setup.
Log in
1. Open the app.
2. Provide user name and password.
3. Conrm with Login.
4. If you are logged in successfully, the home
page shows.
If you want to control smart devices from
multiple mobile devices, install the app on
every mobile device you wish to use and log
in with the same account details on each
mobile device.

Switch Accounts
Do the following to switch between accounts:
1. Open the app home page.
2. Touch to open the account settings.
3. Select Exit and conrm the prompt.
4. Log in with another account.
Manage your Account
1. Open the app homepage.
2. Touch to open the account settings:
Personal settings
Update your account details.
Change password
Change your account password.
Connect to router
Connect to a different network.
Privacy Notice
Read the Privacy Notice.
Exit
Log out.

Home Page
The home page lists all gateways that are
under your account's control.
When you log in for the rst time, the device list
is blank.
Main Controls
Account settingsDevice list
Gateway On/Off
Refresh
device list
Add gateway

Gateway
The gateway is the brain of your automation
setup. Through the app you control the
gateway and all its linked end-node devices via
WiFi or mobile network.
Add a Gateway
During set-up keep the mobile device
running the app and the gateway within
receiving distance of the wireless access
point (AP).
A gateway cannot be linked to two accounts.
Adding a gateway to a second account will
remove it from the rst.
Make sure you know how to operate the
gateway hardware before you start. Refer to
its hardware instructions if necessary.
1. Connect your mobile device running the
app to your WiFi network.
2. Connect the gateway to a wall socket.
3. Open the app home page.
4. Touch +.
5. Follow the on-screen instructions.
6. Touch to refresh the device list.
7. The gateway shows on the device list.

Open the Gateway
Dashboard
Select a gateway from the home page to open
the gateway dashboard.
Gateway Dashboard
End-node devices
Global control
Gateway socket on/off
Add end-node device

Open the Device Menu
The device menu gives you access to tools
for device managament. Access the menu as
follows:
1. Open the gateway dashboard.
2. On the dashboard, touch to open the
menu.
Control
Before you start controlling devices, note the
following important points:
If the power supply to the gateway interrupts,
all end-node-device-to-cloud connections
interrupt also.
The gateway's socket is controlled
independently of linked end-node devices.
If you turn off the gateway's socket, the end-
node devices are left unaffected.

Attention!
Your device may not be designed for
operation without supervision, and
thus present serious danger under
certain conditions.
Never remote or autocontrol such a
device.
Manual Control
You can manually control the gateway socket
from three locations through the button:
■Home page
■Gateway dashboard
■Device menu (includes status)
Globally Control End-node
Devices
Turn all linked end-node devices (excluding
sensing devices, e.g. temperature sensor) on
or off at the same time. Do the following:
1. Open the gateway dashboard.
2. Touch ALL ON or ALL OFF respectively.
3. Conrm the prompt to continue.

Set a Timer
The timer turns the gateway's socket on or off
respectively after the countdown expires. Do
the following:
1. Open the device menu.
2. Select Timer.
3. Decide if the timer shall turn the socket on
or off. Select the corresponding timer.
4. Set the time.
5. Touch to start. After the timer expires,
the socket is turned on or off.
Schedules
Set a Schedule
Control the socket according to a preset
schedule. Do the following:
1. Open the device menu.
2. Select Schedule.
3. Touch +.
4. Enter schedule details into the schedule
panel.
-Note: On and Off cannot occur at the
same time.
5. Touch to save.
6. The schedule is added to the schedule
view.
You can set at most 30 schedules.

Schedule Panel
Save schedule
Day selection
Schedule View
Enable/Disable schedule

Modify a Schedule
1. Open the schedule view.
2. Hold down the schedule you want to edit.
3. Select Modify from the menu.
4. Edit the schedule.
5. Touch to save.
Delete a Schedule
1. Open the schedule view.
2. Hold down the schedule you want to delete.
3. Select Delete from the menu.
4. Conrm the prompt to delete the schedule.
Control Log
The control log logs device activity.
The log shows you when and how the event
was triggered (e.g. manually, through timer)
and what the action was (e.g. turned off, turned
on).
View Log
1. Open the device menu.
2. Select Control log.
3. Touch to refresh the log.
4. Read the log:
-event handled successfully
-event handling failed

Clear Log
1. Open the device menu.
2. Select Control log.
3. Touch .
4. Conrm the prompt to clear the log.
Manage Gateways
Rename a Gateway
1. Open the device menu.
2. Select Rename from the menu.
3. Update the name and conrm your
changes.
4. Navigate to the app homepage so that the
name refreshes across all views.
Replace a Gateway
Replace an existing gateway with another one.
All linked end-node devices and their settings
are carried over. Do the following:
1. Open the device menu.
2. Select Replace gateway from the menu.
3. Follow the on-screen instructions to
complete the replacement.