Symcod LBC-02/IP User manual

1171 West Notre-Dame
Victoriaville, QC
CANADA
G6P 7L1
Telephone: [phone] or [phone]
Fax: [phone]
LBC-02/IP
TELNET VT-100 EMULATION
COMPATIBLE
AS/400, Unix, Linux, Windows
Documentation Version (07/08/2007)
Use this documentation with the product : LBC-02/IP
Our Internet site: http:// www.symcod.com/
Programmer Analyst: Steve Bilodeau
Email: [e-mail]

LBC-02/IP
TELNET VT-100 EMULATION
DEFAULT KEYBOARD MAPPING:
M1 = F1 (ESC 1)
M2 = F2 (ESC 2)
M3 = F3 (ESC 3)
M4 = F4 (ESC 4)
M5 = TAB (ASCII 9)
ESC = RESET (ESC R)
LBC-02 KEYPAD SEQUENCES (Make this sequence directly on the LBC-02/IP KeyPad):
ESC .0 = Go to BOOT mode (In terminal Mode)
ESC . 1 = Reset TCP/IP connection and Close TCP connection (In terminal Mode)
ESC .9 = Show IP Configuration (In terminal Mode)
ESC .H = Cursor position HOME (In terminal Mode)
BARCODE AND TTLIN SUFFIX CONFIGURATION, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><A = SUFFIX ASCII 13 (ENTER)
><B = SUFFIX ASCII 9 (TAB)
><C = SUFFIX ASCII 0 (NOTHING)
BARCODE PREFIX CONFIGURATION, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><Fxx = PREFIX ASCII xx (00 to FF) *00 = nothing
TTL OUTPUT, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
• Output TTL x ON/OFF
><Txy
x = TTL Number 1 to 4
y = E for Enable or D for Disable
Sequence example, set TTL output 2 to ON: ><T2E
• Output TTL x during y seconds (y = +- 1 second)
><TxTy
x = TTL Number 1 to 4
y = Delay (Two digits)
Sequence example, set TTL output 2 to ON during 4 seconds: ><T2T04

KEYBOARD CONFIGURATION, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><K0 = Barcode set to OFF
><K1 = Barcode set to ON
><K2 = Keyboard set to OFF
><K3 = Keyboard set to ON
><K4 = Keyboard and Barcode set to OFF
><K5 = Keyboard and Barcode set to ON
><K6 = Keyboard mapping for UNIX
><K7 = Keyboard mapping for AS/400
><K8 = Keyboard AS/400 M5 = F5
><K9 = Keyboard M5 = TAB
><KH = Keyboard AS/400 ESC = F12
* In mode Keyboard and/or Barcode OFF, the Light LED of your terminal is locked to ON
GENERAL CONFIGURATION, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><KT = Disable Time and Date display
><KJ = Half Duplex mode (Default)
><KK = Full Duplex mode
><KL = CapsLock ON (Default)
><KM = CapsLock OFF
><KN = Change cursor position: Line 2 Column 1
><KZ = ESC
><KPx= Pause x, 1 = .5 secondes (possible values 1 to 9, A to Z, a to z)
><KWx=Watch dog configuration 0 = OFF, 1 = ON
GENERAL CONFIGURATION, IF YOU SEND THIS SEQUENCE AT ANY POSITION:
><KI = Clear Screen
KEYBOARD DEFINES, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE (Ver. 1.4L or more):
><KAx = Key M1 = character x
><KBx = Key M2 = character x
><KCx = Key M3 = character x
><KDx = Key M4 = character x
><KEx = Key M5 = character x
><KFx = Key ESC = character x
><KGx = Key ENTER = character x
If x = . then Key = Default value
If x = - then Key = Tab

TTL IN Enable / Desable / Request Status, , IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><TxIy
x = TTL Number 1 or 2
y = Sets the terminal TTL IN x to 0-DESABLE, 1-ENABLE 2-Request Status (Default = Disable)
Sequence example, set TTL input 2 set to Enable: ><T2I1
TTL IN RETURN: &xy
x = TTL Number 1 or 2
y = Status 0 or 1
Sequence example, TTL input 2 change: &21
LIGHT LED AND EMIT SOUND, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><H = Light LED
><I = Emit SOUND
><J = Light LED and Emit SOUND
><L0 = Barcode BIP validation OFF
><L1 = Barcode BIP validation ON
SET CURRENT DATE AND TIME, IF YOU SEND THIS SEQUENCE AT LINE 3 OR MORE :
><EHHMMSSE = SET THE CURRENT TIME
><DMMDDYYD = SET THE CURRENT DATE
SHOW TIME, THE TERMINAL REPLACES THIS CHARACTER BY THE CURRENT TIME:
CHR(240) or > = Show and refresh time.
SHOW DATE, THE TERMINAL REPLACES THIS CHARACTER BY THE CURRENT DATE:
CHR(241) or < = Show and refresh date.
CHANGE CURSOR POSITION:
Chr(27) + "[" + POS_Y + ";" + POS_X + "H"
CLEAR SCREEN:
Chr(27) + "[2J"

IP CONFIGURATION WITH BoardConfig SOFTWARE
BOARD CONFIG VERSION 1.1E or more
1. Select the terminal in IP DEVICES LIST (click)
2. Enter the IP and Net Mask of this terminal (Bauds = 57600 Parity = 0 Databits = 0)
3. Check the MODE ACTIVE &KeepAlive
4. Enter the Host IP and (Host Port = 23)
5. Check the Auto Boot
6. Enter your login string
Example: ~~USER^9^PASSWORD^13^
Description: [Pause .5 Secs.] USER [TAB] PASSWORD [ENTER]
7. Push the button: SAVE CONFIG IN TO IP DEVICE
AS/400 WORKSTATION ID:
* BoardConfig software version 1.1L or more supports WORKSTATION ID for AS/400
* This functionality is available on SYMCOD DEVICE VERSION 1.9A and more.
* You can see your product DEVICE VERSION in the BOARD CONFIG software.
MODE PASSIVE
*To open a connection with the LBC-02/IP in mode PASSIVE use the port: 1024
In TERMINAL mode you can:
- Press successively ESC. 0 to return to BOOT mode
- Press successively ESC. 1 to reset TCP Connection
- Press successively ESC. 9 to see the terminal IP configuration
- Press successively ESC. H to Change cursor position: Line 1 Column 1