Symetrix 304 User manual

304 Headphone Amplifier
Users Guide
304

i
Table of Contents
Chapter 1 Introduction 1
Chapter 2 Operator Safety Summary 2
Chapter 3 Fast Setup 3
Chapter 4 Front & Rear Panel Overview
Chapter 5 Using the 30 5
Chapter 6 Applications 6
Chapter 7 Block Diagram 7
Chapter 8 Troubleshooting 8
Chapter 9 Specifications 9
Chapter 10 Warranty and Service 10
Chapter 11 Declaration of Conformity 13
Rev A, 31 October, 1998
Symetrix part number 5330 -0A00
Subject to change without notice.
©1998, Symetrix, Inc. All right reserved.
Symetrix is a registered trademark of Symetrix, Inc.
Mention of third-party products is for informational
purposes only and constitutes neither an endorsement
nor a recommendation. Symetrix assumes no
responsibility with regard to the performance or use
of these products.
Under copyright laws, no part of this manual may be
reproduced or transmitted in any form or by any
means, electronic or mechanical, including photo-
copying, scanning, recording or by any information
storage and retrieval system, without permission, in
writing, from Symetrix, Inc.
6408 216th St. SW
Mountlake Terrace, WA 98043 USA
Tel [phone]
Fax [phone]
Email: [email protected]
304

304
1
IntroductionChapter 1
Front panel
Rear panel
LEVEL 4
10
PWR
LEVEL 3
10
0
10
0
10
0
LEVEL 1 LEVEL 2
0
HEADPHONE LEVEL
OUTPUT 3
MODE
MONO
STEREO
OUTPUT 1 OUTPUT 2
LEVEL
+12
+25
∞
HEADPHONE
AMPLIFIER
304
INPUT HEADPHONE OUT
OUTPUT 4
LINE INPUTS
INPUT BTHRU A INPUT A
POWER
INPUT OR PS-3E POWER
SUPPLY ONLY.
THIS PRODUCT CONTAINS NO USER SERVICABLE PARTS.
RÉFÉREZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.
FABRIQUÉ AUX E.-U. PAR SYMETRIX INC., LYNNWOOD, WASHINGTON.
MANUFACTURED BY SYMETRIX INC. LYNNWOOD, WA USA
CONNECT TO
SYMETRIX PS-3
THRU B
PASS THRU
The Symetrix 304 Headphone Amplifier is a 1-
in 4-out amplifier designed to drive multiple
headphones of any impedance. Symetrix
proprietary high voltage drive technology
gives the 304 the a ility to drive high imped-
ance headphones with the equivalent output
voltage of a much larger power amplifier, yet
provides more than ample current for low
impedance phones. The four stereo outputs
automatically adjust output power to match the
load impedance.
Controls provided are input level, output level
for each individual amplifier, and a stereo/
mono switch.
The STEREO/MONO switch allows the amplifier
to e used several ways. As a normal stereo
amplifier (with four outputs), the left and right
inputs are used for stereo signals, which feed
the left and right outputs. Switching to mono
with a stereo input provides a quick check of
the mono compati ility of a stereo mix. For
that matter, you may want to monitor in mono.
As a mono amplifier, one signal fed to either
input will feed oth outputs. Also in mono
mode, when two different mono signals are fed
to the left and right inputs, they will e mixed
to feed oth the left and right outputs.
The inputs are electronically alanced, ut will
operate normally in an un alanced configura-
tion when 2-conductor 1/4" plugs are inserted.
The outputs are 1/4" stereo connectors.
Do you hate reading manuals? Chapter 3 of
this manual was written just for you.
Pleeeeeze! Skip the rest of this and just read
Chapter 3. It will get you up and running with
minimum reading and minimum pain. Try to
read the rest of the manual later. It's worth it.
Should you have any comments or questions,
please do not hesitate to contact us. Your calls
and e-mail are always welcome.
Phone:[phone]
Fax:[phone]
Email: [email protected]
We site: www.symetrixaudio.com

304
2
The information in this summary is intended
for persons who operate the equipment as well
as repair personnel. Specific warnings and
cautions are found throughout this manual
wherever they may apply.
The notational conventions used in this manual
and on the equipment itself are descri ed in the
following paragraphs.
The lightning flash with arrowhead sym ol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated
dangerous voltage within the product’s
enclosure that may e of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user of the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the 304 (i.e. this manual).
Caution To prevent electric shock, do not
use the polarized plug supplied
with the 304 with any extension
cord, receptacle, or other outlet
unless the blades can be fully
inserted.
Terms
Several notational conventions are used in this
manual. Some paragraphs may use Note,
Caution, or Warning as a heading. Certain
typefaces and capitalization are used to
identify certain words. These are:
Note Identifies information that needs
extra emphasis. A Note generally
supplies extra information to help
you to etter use the 304.
Equipment Markings
Operator Safety Summary Chapter 2
Caution Identifies infor ation that, if not
heeded, ay cause da age to the
304 or other equip ent in your
syste .
Warning Identifies information that, if
ignored, may be hazardous to
your health or that of others.
CAPITALS Controls, switches or other
markings on the 304's chassis.
Boldface Strong emphasis.
Power source - This product is intended to
operate from a power source that does not
apply more than 255Vrms etween the power
supply conductors or etween either power
supply conductor and ground. A protective
ground connection, y way of the grounding
conductor in the power cord, is essential for
safe operation.
Danger from loss of ground - If the protec-
tive ground connection is lost, all accessi le
conductive parts, including kno s and controls
that may appear to e insulated, can render an
electric shock.
In-line power supply - This product receives
its operating power from the Symetrix PS-3 or
PS-3E power supply. This is the only power
supply approved for use with the product. Do
not connect the product to any other in-line, or
plug-in, transformer. The use of other power
sources may cause damage to the equipment or
present a shock hazard to the operator.
Operating location - Do not operate this
equipment under any of the following condi-
tions: explosive atmospheres, in wet locations,
in inclement weather, improper or unknown
AC mains voltage, or if improperly fused.
tay out of the box - To avoid personal injury
or injury to others, do not remove the product
covers or panels. Do not operate the product
without the covers and panels properly
installed.
AVIS:
NE PAS OUVRIR
Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.
SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.
S’adresser a un reparateur compétent.
RISQUE DE CHOC ELECTRIQUE
No user serviceable parts inside. Refer servicing to qualified service personnel
.
CAUTION
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE
DO NOT OPEN
RISK OF ELECTRIC SHOCK

304
3
Fast First-Time Setup
This section is dedicated to users who hate to read manuals.
The 304 is a four-output headphone amplifier. A stereo input drives all four headphone amplifiers.
Each amplifier has an independent level control. There is an overall master level control, and an
overall STEREO/MONO switch.
Wiring
To install the 304:
1. Plug the PS-3 power supply's DIN connector into the 304. Plug the PS-3 into a
suita le source of AC power. Refer to the la elling on the PS-3 to determine what is
suita le.
2. Connect your source to the 304's tip-ring-sleeve input jacks. The inputs are alanced.
They will work with either alanced or un alanced sources.
3. Connect your headphones to the four output jacks. The 304 can handle headphone
impedances ranging from 8-ohms to over 2000 ohms. 60-ohm headphones are
optimal (they get the loudest). It is not necessary for each set of headphones to e the
same (although it might help if they were).
Go!
Set the individual level controls to minimum (max ccw rotation). Set the master level control to the
halfway position (12 noon). Set the stereo/mono switch as appropriate.
With the source signal active, adjust the individual level controls for comforta le listening levels.
CautionThe 304 is capable of driving any headphones past the threshold of pain. This can
also result in hearing da age. For your own hearing health, onitor at the lowest
SPL that you can use and still get the job done.
Fast Setup
Chapter 3

304
4
Front & Rear Panel Overview Chapter 4
LEVEL 4
10
PWR
LEVEL 3
10
0
10
0
10
0
LEVEL 1 LEVEL 2
0
HEADPHONE LEVEL
OUTPUT 3
MODE
MONO
STEREO
OUTPUT 1 OUTPUT 2
LEVEL
+12
+25
∞
HEADPHONE
AMPLIFIER
304
INPUT HEADPHONE OUT
OUTPUT 4
INPUT LEVEL Sets the input signal strength. Fully counterclockwise, no signal. Fully
clockwise, input signals are oosted y 25 dB.
MONO/STEREOCom ines stereo, or two mono, input signals into one mono output signal
(fed equally to oth left and right headphone outputs).
HEADPHONE OUTPUTS 1/4" stereo jacks for headphones. The minimum impedance is 8 ohms
(see Ta le 1 for com ined headphone impedances).
HEADPHONE LEVELS Volume controls set the signal strength at the corresponding output jack
(1-4).
PWR Red LED indicates power on .
LINE INPUTS
INPUT BTHRU A INPUT A
POWER
INPUT OR PS-3E POWER
SUPPLY ONLY.
THIS PRODUCT CONTAINS NO USER SERVICABLE PARTS.
RÉFÉREZ TOUTE RÉPARATION ÀUN TECHNICIEN QUALIFIÉ.
FABRIQUÉAUX E.-U. PAR SYMETRIX INC., LYNNWOOD, WASHINGTON.
MANUFACTURED BY SYMETRIX INC. LYNNWOOD, WA USA
CONNECT TO
SYMETRIX PS-3
THRU B
PASS THRU
7-PIN DIN CONNECTOR Connect the 7-pin DIN plug end of a Symetrix PS-3 (117V) or PS-3E
(230V) here. Connect the AC power connector end of the PS-3 or
PS-3E to an AC power source that is of the correct voltage and
frequency as marked on the PS-3 or PS-3E.
THRU A TRS jack connected in parallel with INPUT A jack. Use this jack to
connect to other 304's or other audio equipment. Its a uilt-in "Y"
cord.
THRU B TRS jack connected in parallel with INPUT B jack. Use this jack to
connect to other 304's or other audio equipment. Its a uilt-in "Y"
cord.
INPUT A (Left channel) 3 conductor 1/4" jack for line level alanced or un alanced input
signals. Tip = high (+), Ring = low (-), Sleeve = ground.
INPUT B (Right channel) 3 conductor 1/4" jack for line level alanced or un alanced input
signals. Tip = high (+), Ring = low (-), Sleeve = ground.

304
5
Chapter 5 Using the 304
Impedance, Sensitivity, Loudness
Loudness is directly related to the impedance and sensitivity of the headphones. Impedance
determines how much power the headphones will draw, while sensitivity indicates how much of
the electrical signal delivered to the headphones is converted into sound.
Because low impedance headphones draw more power from the amplifier they will sound louder,
at the same control settings, than high impedance headphones. Also, headphones of higher
sensitivity will sound louder than those of lower sensitivity. Check the manufacturer's spec sheet
for impedance and sensitivity information.
Proprietary high voltage driver technology allows the 304 to drive even high impedance head-
phones to maximum levels, ecause the amplifiers are capa le of very high output voltage swing.
However, to get a loudness equivalent to that of low impedance headphones, the controls will have
to e set to higher settings when using high impedance headphones. This is normal.
If low and high impedance headphones are com ined on the same channel, the low impedance
headphones will e much louder. As a result, when a com ination of high impedance and low
impedance headphones is used, only those of like impedance should e used on the same channel.
This allows each listener to properly adjust loudness, without regard to the impedance and sensi-
tivity of the other headphones. (It's ok to mix impedances on the same amplifier, its just not
optimum. You won t hurt anything.)
Maximum Amplifier Load
The minimum operating impedance, or maximum load, for each output of the 304 is 8 ohms. Use as
many pairs of headphones as desired, as long as the total com ined impedance (per output) does not fall
elow 8 ohms. Ta le 1 shows how many headphones of various impedances may e used with each
output of the 304.
Ta le 1 - Com ined Impedance Values (approx. 8:)
Impedance of Headphones Maximum Number/Channel
8 (see note 1) 1
16 2
32 4
100 10
200 20
400 40
600 60
Note 1: The quantities given a ove reflect usage with typical wide-range musical signals. If you
are driving low-impedance headphones (16-ohms or lower actual impedance), and you intend to
drive them to the rink of amplifier clipping, then you should revise the num er of headphones
possi le (per 304) to 2 8-ohm headphones or 4 16-ohm headphones (for the 8-ohm case, you ll
have two amplifier channels that aren't doing anything). It is OK to use any remaining amplifier
channels with higher impedance phones (50 ohms or higher).
For maximum output with all channels driven, try to restrict the lowest com ined load impedance
to 50 ohms per channel. Lower impedance loads simply reduce the maximum output possi le.
Note 2:Many headphones are spec'd as eing suita le for eight-ohm outputs. They are, ut this
does not mean that their actual impedance is 8-ohms. In most cases, the actual impedance is
su stantially higher. This is good (rather than ad). For whatever it's worth, most decent
headphones have actual impedances ranging from 50 ohms and up.
Note 3.When multiple headphones are required with each output, use headphone type "Y" cords,
or a reakout ox. A reakout ox may have as many paralleled 1/4" stereo jacks as necessary,
as long as the num ers in Ta le 1 are not exceeded.

304
6
Applications Chapter 6
The 304 can e used in the following applications. Please note that this list is far from comprehensive
and your imagination may create new uses that we haven t listed here.
PROJECT TUDIO Let the 304 expand your mixer s headphone capacity. You can drive it
via a tip-ring-sleeve to dual tip-sleeve ca le from your mixer's
headphone jack, or from one or two of your mixer's aux sends. If you
only use one aux send, then press the stereo/mono switch to route the
signal to oth channels.
BROADCA T Use the 304 to drive the guest headphones in your studio.
Does your console have an anemic headphone amplifier? The 304 will
make it roar.
LIVE OUND Does your console have an anemic headphone amplifier? The 304 will
make it roar.
HOU E OF WOR HIP Create assistive listening stations at several pews. Drive the 304 with a
mixture of the sound reinforcement signal and a room microphone.
No, this isn't as sophisticated as one of the RF or infrared systems, ut
it doesn t cost like they do either!
BALANCED Here s how to use the 304 as a one-in, four out alanced line amplifier.
LINE DRIVER Make a wye ca le so that you can drive oth inputs in parallel. Wire the
plug for the right-channel input so that it is reverse polarity from the
left-channel input.
Connect your source to the "Y"-ca le's input.
Connect each of your alanced loads to the tip-ring-sleeve output
connectors. The tip connection is hot.

304
7
Block DiagramChapter 7
OUTPUT
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
CHANNEL
LEVEL
MONO
STEREO
INPUT A
INPUT B
MASTER
VOLUME
Rev-B

304
8
Troubleshooting Chapter 8
Troubleshooting Chart
YMPTOM PROBABLE CAU E
No output Check ca les and connections. Are inputs driven y outputs, and
outputs driving inputs? Verify ca les, source and load. Check for AC
power presence.
Hum or buzz in output Check input and output connector wiring. Ground loop: check related
system equipment grounding. Are all system components on the same
AC ground?
Distortion Check input signal. Is it too hot, or is it already distorted? Check the
output loading. Is something else clipping?
Noise (hiss) Check input signal levels. The 304 is intended to operate at or near
line level (+4dBu is nominal). Make sure that the signal you are
feeding to the 304 is a line level signal, not mic level. Make sure that all
systems components are on the same AC ground. Check gain settings on
upstream equipment. The system gain structure should e such that
the 304 receives +4dBu nominal signal. Is the input signal already
noisy?
No LED display Is the unit plugged in? Is the AC outlet OK?

304
9
Architects and Engineers Specifications
SpecificationsChapter 9
Specifications
In the interest of continuous product improvement, Symetrix, Inc.
reserves the right to alter, change, or modify these specifications
without prior notice.
©1998, Symetrix, Inc. All rights reserved.
The headphone amplifier shall have a single
stereo input and four stereo outputs. Each
output shall have its own amplifier and volume
control. An overall volume control (master)
shall also e provided. There shall e an
overall stereo/mono switch.
All inputs are alanced ridging inputs.
Outputs shall e suita le for driving head-
phones in the range of 8 ohms to 2000 ohms.
The output source impedance shall e 100
ohms.
Input/Output
Input Type Bridging, Balanced or Unbalanced
Maximum Input Level +18dBu Balanced
Maximum OutputLevel 21dBm, 600 Ohm load,
>6VRMS, 200 Ohm load
Input Impedance 20k Ohms Balanced, 10k Ohms Unbalanced
Output Impedance 100 Ohms
Performance Data
Frequency Response 20Hz to 20kHz, +0, -1 dB
THD+Noise .01% (1kHz, 0dBm, 600 Ohms)
.02% (1kHz, +20dBm, 600 Ohms)
Signal-to-NoiseRatio 95dB
Maximum Gain 25dB
Connections
Input 1/4" in. TRS
Output 1/4" in. TRS
Power In 7 pin DIN
Physical
Size (hwd) ˚ rack unit
1.75 x 8.5 x 6.5 in., 4.445 x 21.59 x 15.875 cm.
Shipping Weight 4.5 lbs
Electrical
Power Requirements 117V nominal, 95 to 130V AC, 50 to 60 Hz
230V nominal, 207 to 253V AC, 50 Hz
The headphone amplifier shall e capa le of
delivering 35 volts peak-to-peak into a 2000
ohm load (or greater).
The unit shall e capa le of operating y
means of a Symetrix PS-3 or PS-3E external
power supply connected to 117V nominal AC
(95 to 130V), 50/60 Hz or 230V nominal AC,
207 to 253V AC, 50 Hz where applica le.
The unit shall e a Symetrix, Inc. model 304
Headphone Amplifier.

304
10
Warranty and Service Chapter 10
Symetrix, Inc. expressly warrants that the product
will e free from defects in material and
workmanship for (18) months. Symetrix’s
o ligations under this warranty will e
limited to repairing or replacing, at
Symetrix’s option, the part or parts of the
product which prove defective in material or
workmanship within (18) months from date
of shipment, provided that the Buyer gives
Symetrix prompt notice of any defect or
failure and satisfactory proof thereof.
Products may e returned y Buyer only
after a Return Authorization num er (RA)
has een o tained from Symetrix. Buyer will
prepay all freight charges to return the
product to the Symetrix factory. Symetrix
reserves the right to inspect any products
which may e the su ject of any warranty
claim efore repair or replacement is carried
out. Symetrix may, at its option, require
proof of the original date of purchase (dated
copy of original retail dealer’s invoice).
Final determination of warranty coverage
lies solely with Symetrix. Products repaired
under warranty will e returned freight
prepaid y Symetrix via United Parcel
Service (surface), to any location within the
Continental United States. At Buyer’s
request the shipment may e returned via
airfreight at Buyer’s expense. Outside the
Continental United States, products will e
returned freight collect.
The foregoing warranties are in lieu of all
other warranties, whether oral, written,
express, implied or statutory. ymetrix,
304 Limited Warranty
Limitation of Liability
The total lia ility of Symetrix on any claim,
whether in contract, tort (including negli-
gence) or otherwise arising out of, connected
with, or resulting from the manufacture, sale,
delivery, resale, repair, replacement or use
of any product will not exceed the price
alloca le to the product or any part thereof
which gives rise to the claim. In no event
will Symetrix e lia le for any incidental or
Inc. expressly disclaims any IMPLIED
warranties, including fitness for a par-
ticular purpose or merchantability.
ymetrix’s warranty obligation and
buyer’s remedies hereunder are OLELY
and exclusively as stated herein.
This Symetrix product is designed and
manufactured for use in professional and
studio audio systems and is not intended for
other usage. With respect to products
purchased y consumers for personal,
family, or household use, Symetrix ex-
pressly disclaims all implied warranties,
including but not limited to warranties of
merchantability and fitness for a particu-
lar purpose.
This limited warranty, with all terms,
conditions and disclaimers set forth herein,
shall extend to the original purchaser and
anyone who purchases the product within the
specified warranty period.
Symetrix does not authorize any third party,
including any dealer or sales representative,
to assume any lia ility or make any addi-
tional warranties or representation regarding
this product information on ehalf of
Symetrix.
This limited warranty gives the uyer certain
rights. You may have additional rights
provided y applica le law.
consequential damages including ut not
limited to damage for loss of revenue, cost
of capital, claims of customers for service
interruptions or failure to supply, and costs
and expenses incurred in connection with
la or, overhead, transportation, installation
or removal of products or su stitute facilities
or supply houses.

304
11
If you have determined that your 304 requires repair services and you live outside of the
United States, please contact your local Symetrix dealer or distri utor for instructions on how
to o tain service. If you reside in the U.S. then proceed as follows:
Before sending anything to ymetrix, contact our Customer Service Department for a return
authorization (RA) num er. The telephone num er is [phone] or email:
[email protected]
In-warranty Repairs
To get your 304 repaired under the terms of the warranty:
1. Call us for an RA num er.
2. Pack the unit in its original packaging materials.
3. Include your name, address, daytime telephone num er, and a rief
statement of the pro lem.
4. Write the RA num er on the outside of the ox.
5. Ship the unit to Symetrix, freight prepaid.
We do not accept freight collect shipments.
Repairs made in-warranty will cost you only one-way freight charges. We'll prepay the return
(surface) freight.
If you send us your product in su standard packaging, we will charge you for factory shipping
materials. If you don t have the factory packaging materials, please use an oversized carton,
wrap the unit in a plastic ag, and surround it with u le-wrap. Pack the ox full of
Styrofoam peanuts. Be sure there is enough clearance in the carton to protect the rack ears
(you wouldn't elieve how many units are returned with ent ears). We will return the unit in
Symetrix packaging. Of course, if the repair is due to operator error, parts and la or will e
charged. In any event, if there are charges for the repair costs, you will pay for the return
freight. All charges will e COD unless you have made other arrangements (prepaid, Visa or
Mastercard).
Out-of-warranty Repairs
If the warranty period has passed, you'll e illed for all necessary parts, la or, packaging
materials, and freight charges. Please remem er, you must call for an RA num er efore
sending the unit to Symetrix.
Servicing the 304

304
12

304
13
Declaration of ConformityChapter 11
Declaration of Conformity
We, ymetrix Incorporated,
6408 216th St. SW, Mountlake Terrace, Washington, USA,
declare under our sole responsi ility that the product:
304 Headphone Amplifier
to which this declaration relates,
is in conformity with the following standards:
EN 60065
Safety requirements for mains operated electronic and related
apparatus for household and similar general use.
EN 50081-1
Electromagnetic compatibility - Generic emission standard
Part 1: Residential, commercial, and light industry.
EN 50082-1
Electromagnetic compatibility - Generic immunity standard
Part 1: Residential, commercial, and light industry.
The technical construction file is maintained at:
ymetrix, Inc.
6408 216th St. SW
Mountlake Terrace, WA, 98043
USA
The authorized representative located within the European Community is:
World Marketing Associates
P.O. Box 100
St. Austell, Cornwall, PL26 6YU, U.K.
Date of issue: Octo er 31, 1998
Place of issue:Mountlake Terrace, Washington, USA
Authorized signature:
Dane Butcher, President, ymetrix Incorporated.

304

304

304
18
ymetrix, Inc.
6408 216th St. SW
Mountlake Terrace, WA, 98043
USA
Tel: [phone]
Fax: [phone]
We site: http://www.symetrixaudio.com
Email: [email protected]