Synel 765 User manual

Synel Americas
8665 E Hartford Dr Suite 100
Scottsdale, AZ. 85255
480-37 4-7700
www.synel-americas.com
[email protected]
V Feb 2020
765 SYNEL AMERICAS
Product Manual & Guide

- 1 -
1.0 Technical Specifications
1.1 Specifications
Dimensions
9.8” x 6.7” x 3.7”
Weight
2.5 lbs.
Memory
512K RAM, Battery backed.
Reader
Magnetic Stripe (track 1,2,or 3)– Optional
Bar Code (0-of-9, 2-of-5,128)
Proximity Reader (HID 26Bit) – Optional
Display 2x16 LCD backlit Alphanumeric with Decimal point
Programming ASCII-based, Over Communication Port
Communications Standard: RS-232 Port - Bi-directional Local
Communications Standard: RS-485 Port
Optional: 10/100 Ethernet
Power Voltage: 110/230 Vac + 10%, 100mA
Environment Operating Temperature -20o-60oC
Humidity: up to 95% RH
1.2 Available Options
Ethernet Communications: With the optional internal Ethernet card, the terminal can be connected to any 10/100
Ethernet network.
Wi-Fi (Wireless) Communications: The SY-765's wireless card allows the 765 to communicate over a
standard 802.11b network. The wireless network must be configured with an IP address, gateway, subnet, and
WEP key (if available).
P.O.E. (Power over Ethernet: The SY-765 has the optional capability of drawing its power from the Ethernet
communications line. This eliminates the need for high voltage power at the terminal locations. Note: The
Ethernet Network must support POE communications.
External Readers: The SY-765 has two reader ports to connect external devices such as a Bar code Gun or
an Access Control Swipe Reader that could be mounted outside a door.
1.3 Features
The SY-765 is constructed of injection molded plastic, which, pound for pound is stronger than steel, yet
lightweight and attractive. The terminals have recessed membrane keypads, which create a watertight seal
against external elements.

- 2 -
1.3.1 Front Panel
and line down maneuvering.
1.3.2 Bottom Connector Panel
The connector panel is located at the lower part of the casing, withholding the socket openings for all external
connections as follows (from left to right):
1. External secondary Reader 2 – for optional external readers
2. External secondary Reader 1 – for optional external readers
3. I2C – I/O Extension (N/A) – not used
4. Network
5. Serial I – Serial port connection for printer (N/A) – not used
6. Host – RS-232 / RS-485 Communications
1.4 Internal Components
The SY-765 has two back-up battery modules, one for the real time clock memory and the other for operation
during a power failure.
The standard memory back-up module is a lithium battery, which will keep the internal clock running and the memory
intact, for 30daysduring a power failure.
The back-up battery provided (in addition to the standard memory back-up) is a self-recharging system which allows
the terminal to operate during a power failure. The battery provides power for one and a half net hours of use. A shut
down timeout feature enables the terminal to operate for more extended periods of time.
The SY-765 Terminal has the following front panel features:
1. 2x16 Character LCD backlit display.
a. The terminal comes with a highly advanced filtered LCD display. This means that under almost any
lighting condition, the terminal will give you a clear picture to read the screen.
2. Two arrow keys are located to the right of the display panel for line up
a. The arrow keys are also used for getting into Technician mode.
3. Eight Function keys located on the left, below the display.
a. [IN], [OUT], [F1], [F2], [F3], and [F4].
4. A numerical keyboard of fourteen keys, including [Enter], [Back Space], [Dot] and [Clear].
5. The Alarm light “!”, is located to the left of the display.
a. The alarm light is an LED that lights when at least half of the memory is used; it blinks when the
memory is almost full.
6. The ON button enables a 15 second manual operation window if the terminal is on battery back-up power.

- 3 -
During a power failure, the user presses the battery key to activate the terminal. Data can then be entered and
stored in the SY-765 memory. The time-out will cause the terminal to shut down automatically after the last
use of the terminal, until the battery key is pressed again.
1.4.1 Memory
As a standard feature, the SY-765 Terminal contains a 256 Kbyte user memory, providing storage for data from
more than 10,000 simple operations. This number depends on the length of the programming tables contained
in the memory, and the complexity of the collected data.
The Alarm light “!”, is located to the left of the display. The alarm light is an
LED that lights when at least half of the memory is used; its blinks when the
memory is almost full.
1.2 Internal Components
The SY-765 has two back-up batterymodules, one for the real time clock memory and the other for operation
during a power failure.
The standard memory back-up module is a lithium battery, which will keep the internal clock running and the memory
intact, for 30daysduring a power failure.
The back-up battery provided (in addition to the standard memory back-up) is a self-recharging system which allows
the terminal to operate during a power failure. The battery provides power for one and a half net hours of use. A shut
down timeout feature enables the terminal to operate for more extended periods of time.
During a power failure, the user presses the battery key to activate the terminal. Data can then be entered and
stored in the SY-765 memory. The time-out will cause the terminal to shut down automatically after the last
use of the terminal, until the battery key is pressed again.
1.2.1 Memory
As a standard feature, the SY-765 Terminal contains a 512 Kbyte user memory, providing storage for data from
more than 10,000 simple operations. This number depends on the length of the programming tables contained
in the memory, and the complexity of the collected data.
The Alarm light “!”, is located to the left of the display. The alarm light is an
LED that lights when at least half of the memory is used; its blinks when the
memory is almost full.

-4-
2.0 Unpacking and Installation
Note: Donot throw away the box or packing materials.
Check the box and the contents for any signs of damage that may havehappened during shipment. Carefully unpack
and check the contents.
The SY-765 package contains:
1SY-765 terminal
Mounting panel/back plate
10 meter serial cable.
1 RJ-45 -> DB9F connector.
1 Product CD with the manuals and other tools.
2.1 Location/Site Requirements
The terminal can be installed in any normal office or factory environment. Controlled environments are not required
for proper operation of the terminal. However, installing and operating the terminal under adverse conditions may
affect the functionality of the unit.
2.1.1 Selecting a Location
Consider the following environmental factors that may affect the operation of the terminal, when considering a
location:
•The cable should not be installed near EMI (Electromagnetic Interference) sources, such as:
oMotors, generators, alternators and transformers.
oAir conditioners, elevators, etc.
oRadio/Television transmitters, signal generators and internal communication networks.
•Cables should not be within:
o30 cm. (1 ft.) from 5 KVA power lines or less.
o60 cm. (2 ft.) from 5-10 KVA power lines.
o1.5 meters (5 ft.) of power lines exceeding 10 KVA.
•Cables should not run parallel to power lines for more than 15 m. (49 ft.)
Four Phillips flat head 3.5x30mm and anchors, for terminal mounting purpose.

-5-
2.2 Mounting the Terminal
Make sure the unit is unplugged and that it is not connected to the network/PC.
Caution: The terminal should not be mounted where it will be exposed to
extreme heat or cold, water, steam, violent vibrations, high electromagnetic
radiation including high voltage power lines and electrical equipment.
Place the terminal near an easily accessible power source. Select an appropriate location for the terminal. The
recommended height from the floor is 140 cm (4’ 7”).
1. Remove the back/mounting panel.
2. Using the Mounting Panel place the panel onto the wall at the correct height, making sure that the panel is
level.
a. Mark the three holes for the screws for your drilling locations.
i. Drill holes using drill bit size: 0.23” (6 mm) and insert the plastic screw anchors.
b. Options for power cable and communication wiring.
i. If you are running the wiring within the wall that the clock is mounted to, you have the
option of running the cabling through the center hole of the mounting plate.
ii. If you are bringing the cable from outside the wall, there are knockouts located on both
sides of the cable shield of the mounting plate.
Warning: Live wires in the vicinity may contain 115v or 230v. Make sure not to
drill into any electric wires. Failure to heed this warning may result in serious
injury or death.
3. Mount the back plate making sure that the plate is level.
a. Use the screws that came in the kit to complete the mounting of the back plate.
4. Mount terminal by sliding the unit unto the tabs on the back of the terminal.

-6-
a. Note: Before mounting the terminal to the back plate, you will need to plug in the electrical
connection and the communications wires to the bottom of the terminal before sliding the terminal
into place.
3.0Terminal Configuration
The SY-765 Terminal can be connected to the host computer using either RS-232(Direct), RS-485(LAN),
Ethernet including Wi-Fi.
3.1 Entering Technician Mode
The SY-765 Terminal contains a built in configuration program called Technician mode. Technician mode
enables the set-up of the following options:
Real Time clock I (RTC) calibration
Baud Rate
Printer Baud rate
Station ID settings
Network connection settings
User Field – A field in which the user can fill-in 4 digits that will characterize that terminal
To enter technician mode:
•If the Terminal screen is displaying “NO PROG”.
oPress the
[0]
key 6 times, then press
[Enter]
.

If the clock has a Barcode reader or a Magnetic reader, using a badge with six zeros (000000) will
work as well.
oUse the
[ENTER]
key to move from one screen to the next. To return to the previous screen, use the
[Back Space]
key.
•If the Terminal screen is displaying the date and time.
oSimultaneously press the
and keys 6 times.

If the clock has a Barcode reader or a Magnetic reader, using a badge with six zeros (000000) will
work as well.
oUse the
[ENTER]
key to move from one screen to the next. To return to the previous screen, use the
[Back Space]
key.

-7-
3.2 Communication and Configuration
3.2.1 Communication parameters
Communication between the hostand terminals isperformed under an asynchronous mode. The baud rate is
programmable, enabling rates from 1200 to 19200 bps.
3.2.2 Multiple terminal configurations
RS-485 communication enables you to connect up to 32 terminals to a single COM port and/or to extend the cabling
distance to up to 1,000 meters (3,280 feet) using 9600 baud via an RS-485 multi-drop line. RS-485 communication uses
three wires as opposed to RS-422 communication, which uses four wires.
3.2.3Point to point configuration
A single SY-765 terminal, equipped with RS-232 communications, can be connected directly to an asynchronous
RS-232 port. If RS-232 communication is used, only one terminal may be connected to each COM port and
cabling distances should not exceed 50 ft.
3.2.5 Network connections
The terminal can be connected to one of the following communication networks:
Ethernet (optional card) - For this type of communication, an IP address isdefined for every SY-765 terminal,
enabling communication with each terminal in any 10/100 Ethernet network.
Wi-Fi(optional card) - For this type of communication an SSID isspecified to authorize the connection and an
IP address isdefined for every SY-765 terminal, enabling communication with each terminal in TCP/IP protocol.
WI-FI Technical Specification Table
Card access current
~5V
Module current
~3.3V
Idle power consumption
200mA
Working power consumption
390~420mA
Ripple on card
6m V P-P
Ripple on module
5m V P-P
Pressure on power source at complete terminal capacity
when using WI-
FI/ internal magnetic reader/ external CCD
reader and FPU.
~7.04V
Complete power consumption at complete terminal capacity
when using WI-
FI/ internal magnetic reader/ external CCD
reader and FPU.
~350mA I(JP11)<1A(~250mA)
I(V1)<<1A(small) I(BAT)~100mA
3.3 Terminal Setup
The following describes the different selections within Technician mode in the TA-785 for RS-232 communications.
In bold on the left is the setting on the clock screen, and in bold on the right is the default setting. Unless otherwise
specified, the settings should always be left at the default values.

-8-
3.3.1 RS-232
•
Adjust the RTC (N/Y): N
oOption is for internal clock calibration purposes.
•
Adjust host baud rate: 19200
o
Note:
If using XactTime, the default baud rate should be 9600.
•
Adjust fingerprint unit baud rate: 57600
•
Adjust printer baud rate: 19200
•
Adjust station ID: 0
oThe Station ID is the TA-785’s unique identifier for multi-terminal communication. Any number from 0 to
31 may be used as the ID, but it must match the ID in the software.
•
Adjust the amount of modem rings: N
oChoose
N
for no rings.
•
Network connection: N
oThe main screen enables three modes:
N
for Serial connection,
A
(not used)
B
(10/100Base) Ethernet, or
E
for using WI-FI.
RS-232 uses the default
N
setting.
•
User Field: ####
oSpecify 4 digits which characterize the terminal.
•
FPU - Setting the fingerprint unit mode N
3.3.1.1 RS-232 Connection
The SY-765 terminal can be connected to the host computer via RS-232 with the DB9 Serial Adapter and a
serial cable. The maximum supported cable length for the serial cable is currently 50’.
When plugging the serial cable into the clock, make sure that it is plugged into the HOST port.

-9-
3.3.3 Ethernet Settings
For this type of communication an IP address is defined for every TA-785 terminal enabling communication with each
terminal in any 10/100 Ethernet network.Unless otherwise noted, the default settings in bold on the right should
always be used.
•
Adjust the RTC (N/Y): N
•
Adjust host baud rate: 19200
•
Adjust fingerprint unit baud rate: 57600
•
Adjust printer baud rate: 19200
•
Adjust station ID: 0
•
Adjust the amount of modem rings: N
•
Network connection: B
oThe main screen enables three modes:
N
for serial connection,
A
(not used)
B
(10/100Base)
Ethernet, or
E
for using WI-FI.
•
Polling (Y/N): N
•
MAC Send (Y/N): N
•
My MAC Address(If Y selected above):############
•
My IP Address:###.###.###.###
oUse the numeric keys to enter the IP Address.
•
Gateway Address:###.###.###.###
oUse the numeric keys to enter the Gateway Address.
•
Remote Address:000.000.000.000
oOption not used, always left at all zeros.
•
Subnet Mask:###.###.###.###
oUse the numeric keys to enter the terminal’s subnet mask.
•
My Port:03734
•
Host Port:03734
•
Disconct Sec:30
oDisconnect seconds defines the number of waiting seconds before reverting to offline mode,
can be set up to a maximum value of 99.
•
DHCP (Y/N): N
o
Note:
TA applications uses static IP addresses for communication, as this feature is not
supported. Should always be set to
N
.
3.3.3.1 Ethernet Connection
When plugging the Ethernet cable into the terminal, use the NET port.