Synergy Global Technology Inc RLB-101 User manual

Toll Free: 1-888-865-6888
Tel: [phone] Fax: [phone]
Email: [email protected]

User Manual - Cabinet LED Light Bar - RLB-101

Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
■Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■Any product, on which the serial number has been defaced, modified or removed.
■Damage, deterioration or malfunction resulting from:
□Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
□Repair or attempted repair by anyone not authorized by us.
□Any damage of the product due to shipment.
□Removal or installation of the product.
□Causes external to the product, such as electric power fluctuation or failure.
□Use of supplies or parts not meeting our specifications.
□Normal wear and tear.
□Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

The equipment comes with the standard parts shown on the package contents. Check and make sure they are included
and in good condition. If anything is missing, or damage, contact the supplier immediately.
Unpacking
Package contents
1A Power Adapter Plug Selection
2.5A Power Adapter ( optional )
- LED light bar x 1
- Auto switch power adapter
BS1363
IEC320 C14
NEMA 1-15P AS 3112CEE 7/16
- LED light bar x 2
- Auto switch power adapter
- Y-power cable
with 6 ft C13 - C14 power cord
( RLB-101-2)( RLB-101 )
Single LED Package Dual LED Package
www.RackmountMart.com
(Default)

Connection Diagram
Auto switch power adapter w/ selected plug x 1
Auto switch power adapter w/ selected plug x 1
Cabinet LED light bar w/ IR sensor x 1
- ON / OFF via IR sensor
- 4 cm infrared detection distance
- Magnetic base for easy affixing
Cabinet LED light bar w/ IR sensor x 2
- ON / OFF via IR sensor
- 4 cm infrared detection distance
- Magnetic base for easy affixing
LED
Light Bar
LED
Light Bar
Power
adapter
Y-power cable
RLB-101
RLB-101-2
Single LED Package
Dual LED Package
1
1
2
2
3
200cm
50cm
100cm
www.RackmountMart.com

Dimension Drawing
Specifications
Product RLB-101 RLB-101-2
ON / OFF Auto by IR sensor
Sensing Distance 4 cm
Light Bar No. 12
Light Color Cool White
Lumens ( typ. ) 250 LM
Angel 120° Degree
Color Temperature 2850 - 7100K
LED Life Expectancy 30,000 hrs
Power Input Auto-sensing 100V or 240VAC via power adapter
Consumption 4.5 Watt ( 12V ) per LED light bar
Housing Chassis Extruded aluminum with silver powder coat
Diffuser Acrylic with milky white
Affix Magnetic base for unrestricted installation
Environmental Operating -20 to 40°C Degree ( Indoor )
Dimensions Product ( L x W x H ) 300 x 25 x 13.5 mm
Weight Net 86g ( per LED )
Regulatory Safety / Environmental CE & FCC certified / RoHS & REACH compliant
300 mm
Dip Switch
( left for auto setting )
IR Sensor
13.5
25
Power Input
( mm )
www.RackmountMart.com
The company reserves the right to modify product specifications without prior notice and assumes no responsibility
for any error which may appear in this publication.
All brand names, logo and registered trademarks are properties of their respective owners.
Copyright 2014 Synergy Global Technology Inc. All rights reserved.