Synergy Global Technology RA5024-520-20A-L520 Configuration guide

Rack Power Distribution Unit
General Information
Description This booklet provides information on installing and operating the Rack
Power Distribution Units (PDUs).
24 NEMA 5-20 outlets 20 IEC 320 C13 outlets,
4 IEC 320 C19 outlets
NEMA L5-20 plug NEMA L6-20 plug


RA5024-520-20A-L520 RA5024-C-20A-L620

General Information
2 Rack Power Distribution Unit
Inventory
Receiving inspection Inspect the package and contents for shipping damage, and make sure
that all parts were sent. Report any damage immediately to the shipping
agent, and report missing contents, damage, or other problems
immediately to us.
Please recycle
Quantity Item
2 Cord retention tray (with 8 flat-head screws and
24 wire ties)
2 Mounting brackets (with 4 flat-head screws)
1 Warranty registration card
The shipping materials are recyclable. Please save them for
later use, or dispose of them appropriately.

Rack Power Distribution Unit 3
How to Install the Rack PDU
Attach the cord
retention trays
Attach the cord retention trays to the Rack PDU, using four flat-head
screws (provided) per tray.
Attach cords to the tray Attach a cord to the tray by looping the cord and securing it to the tray,
using a wire tie (provided).
Note
Each cord must be secured to the tray so that you can
unplug it from the Rack PDU without removing the wire
tie.

How to Install the Rack PDU
4 Rack Power Distribution Unit
Mounting options You can install the Rack PDU in one of two ways: using toolless
mounting pegs (provided) or the mounting brackets (provided).
• To install the Rack PDU using the toolless mounting method,
install it in the rear of the NetShelter VX Enclosure, in the cable
channel directly behind the rear vertical mounting rails.
• To install the Rack PDU using the mounting brackets, install it on a
vertical mounting rail on your rack or enclosure.
Toolless mounting 1. Slide the mounting pegs into the holes located in the channel in the
rear panel of the enclosure.
2. Snap the Rack PDU into place by pushing it downward until it
locks into position.
Note
You can mount two Rack PDUs on one side of the enclosure
by using the toolless mounting method.

How to Install the Rack PDU
Rack Power Distribution Unit 5
Bracket-mounting To mount the Rack Rack PDU vertically in a NetShelter®or any
standard EIA-310 rack or enclosure:
1. Attach the vertical-mounting brackets to the Rack PDU.

How to Install the Rack PDU
6 Rack Power Distribution Unit
2. Install the Rack PDU on a vertical mounting rail in your rack or
enclosure.

Rack Power Distribution Unit 7
Specifications
Electrical
Nominal input voltage 120 V 208V
Acceptable input voltage ± 10% Nominal input voltage
Input frequency 47– 63 Hz
Cord length 10 ft
Input connectors NEMA L5-20 plug NEMA L6-20 plug
Output connectors 24 NEMA 5-20 outlets 20 IEC 320 C13;
4 IEC 320 C19 outlets
Maximum total current draw 16A
Physical
Size (H × W × D) 63.75 ×2.19×1.73 in
(161.92 ×5.56×4.39 cm)
Weight 10 lb (4.54 kg)
Environmental
Elevation (above MSL)
Operating
Storage
0–15 000 ft (0–4500 m)
0–50 000 ft (0–15 000 m)
Temperature
Operating
Storage
–5 to 45° C (23 to 115° F)
–25 to 65° C (–13 to 149° F)
Humidity
Operating
Storage
5–95% RH, Non-condensing
5–95% RH, Non-condensing
Compliance
Safety verification UL, cUL 60950
RA5024-520-20A-L520 RA5024-C-20A-L620