Synology DS1813+ User manual

Synology DiskStation DS1813+
Quick Installation Guide
Synology_QIG_18Bay_20130321
Downloaded from ManualsNet.com search engine

2
Table of Contents
Chapter 1: Before You Start
Package Contents .............................................................................................................................................................. 3
Synology DiskStation at a Glance.................................................................................................................................... 4
Safety Instructions .............................................................................................................................................................. 5
Chapter 2: Hardware Setup
Tools and Parts for Hard Disk Installation....................................................................................................................... 6
Install Hard Disks................................................................................................................................................................ 6
Start Up Your DiskStation.................................................................................................................................................. 9
Add a RAM Module on DiskStation................................................................................................................................ 10
Replace System Fan........................................................................................................................................................ 12
Chapter 3: Install DSM on DiskStation
Install DSM with Web Assistant...................................................................................................................................... 15
Learn More ........................................................................................................................................................................ 15
Appendix A: Specifications
Appendix B: LED Indication Table
Downloaded from ManualsNet.com search engine

3
Chapter
1
Chapter 1: Before You Start
Before you start setting up DiskStation, please check the package contents to verify that you have received the
items below. Please also read the safety instructions carefully before use to prevent your DiskStation from any
damages.
Package Contents
Main Unit x 1 AC power cord x 1
RJ-45 LAN cable x 2
Screws for 2.5” hard drives x 36 Hard drive tray key x 2
Downloaded from ManualsNet.com search engine

4 Chapter 1: Before You Start
Synology DiskStation at a Glance
No. Article Name Location Description
1) Power Button Front Panel
The power button is used to turn Synology DiskStation on or off.
To turn off Synology DiskStation, press the Power Button and hold it until you
hear a beep sound and the Power LED starts blinking.
2) LED Indicators Front Panel
The LED indicator is used to display the status of the internal disk and the
system. For more information, see "Appendix B: LED Indication Table" on Page
18.
3) Hard Drive Trays Front Panel The hard drive trays are designed for loading the hard drives used in
Synology DiskStation.
4) Hard Drive Tray
Locks Front Panel Each hard drive tray is equipped with one tray lock to lock or unlock the trays to the DiskStation.
5) Power Port Back Panel The power port is where you connect the power cord to Synology DiskStation.
6) Fans Back Panel
The fans are built to exhaust waste heat out of Synology DiskStation. It will start
automatically when the server starts. If the fan is malfunctioning, the system will
play beep sounds every few seconds.
7) USB 2.0 Ports
Back Panel The Synology DiskStation offers USB ports for adding additional external hard
drives, USB printers, or other USB devices.
8) USB 3.0 Ports
9) eSATA 1
Back Panel The eSATA ports are used to connect external SATA disks or Synology
Expansion Units1
10) to Synology DiskStation.
eSATA 2
11) RESET Button Back Panel 1.To restore IP, DNS, passwords for the admin account to default value.
2.To reinstall the Synology DiskStation.
12) LAN Ports Back Panel The LAN ports are where you connect RJ-45 cable to Synology DiskStation.
-----
1For more information about Synology Expansion Unit supported by your DiskStation, please visit www.synology.com .
Downloaded from ManualsNet.com search engine

5 Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Keep Synology product upright. Do not lay it down horizontally.
Do not place the Synology product close to any liquid.
Before cleaning, unplug the power cord first. Wipe Synology product with damp paper towels. Do
not use chemical or aerosol cleaners to clean it.
Do not place the Synology product on a cart, table, or desk, which is not stable to avoid the
product from falling over.
The power cord must plug in to the right supply voltage.
Make sure that the supplied AC voltage
is correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
Risk of explosion if battery is replaced with an incorrect type.
Dispose of used batteries
appropriately.
Downloaded from ManualsNet.com search engine

6
Chapter
2
Chapter 2: Hardware Setup
Tools and Parts for Hard Disk Installation
A screwdriver
At least one 3.5" or 2.5" SATA hard disk
(Please visit www.synology.com for compatible hard disk models.)
Warning: If you install a hard disk that contains data, the system will format the hard disk and erase all data. If you
need the data in the future, please back it up before installation.
Install Hard Disks
1 Insert the hard drive tray key into the hard drive tray lock, turn the key counter-clockwise to unlock the handle
of the hard drive tray, and then remove the key.
2 Press the lower part of the hard drive tray to pop out the handle.
Downloaded from ManualsNet.com search engine

7 Chapter 2: Hardware Setup
3 Pull the hard drive tray handle in the direction as indicated below to remove the hard drive tray.
4 Load the hard disk in the hard drive tray.
For 3.5” Hard Disk: Remove the fastening panels from the sides of the hard drive tray. Place the hard disk
in the hard drive tray. Then insert the fastening panels to secure the hard disk in place.
For 2.5” Hard Disk: Remove the fastening panels from the sides of the hard drive tray. Place the hard disk
in the blue area (shown below) of the hard drive tray, turn the tray upside down, and then tighten the screws
to secure the hard disk.
Downloaded from ManualsNet.com search engine

8 Chapter 2: Hardware Setup
5 Insert the loaded hard drive tray into the empty hard drive bay.
Important: Make sure the tray is pushed in all the way. Otherwise, the hard disk might not be able to function
properly.
6 Press the handle in flush with the front panel to hold the hard drive tray in place.
7 Insert the hard drive tray key into the hard drive tray lock, turn the key clockwise (to the "I" position) to lock the
handle of the hard drive tray, and then remove the key.
8 Repeat the steps above to assemble the other hard disks you have prepared.
9 The disks’ positions are numbered as shown below.
Note: If you want to set up a RAID set, it is recommended that all installed hard disks are of the same size to make
the best use of hard disk capacity.
Downloaded from ManualsNet.com search engine

9 Chapter 2: Hardware Setup
Start Up Your DiskStation
1 Use the LAN cable to connect DiskStation to your switch/router/hub.
2 Connect one end of the power cord to the power port of your DiskStation, and the other to the power outlet.
3 Press and hold the power button to turn on your DiskStation.
Your DiskStation is now online and detectable from a network computer.
Downloaded from ManualsNet.com search engine

10 Chapter 2: Hardware Setup
Add a RAM Module on DiskStation
The optional Synology RAM module 2GB (DDR3) is designed for DiskStation memory expansion. Follow the
steps below to install, check, or remove a RAM module on your DiskStation.
To install the RAM module:
1 Shut down your DiskStation. Disconnect all cables connected to your DiskStation to prevent any possible
damages.
2 Remove the 6 screws that secure the top case. Lift off the case and place it to the side.
Important: When you remove the case, you expose sensitive internal components. Avoid touching anything other
than the memory assembly when you remove or add memory.
3 Insert the new memory module in the slot:
a Align the notch on the gold edge of the module with the notch in the lower memory slot.
b Tilt the card and push the memory into the slot. Make sure the module is pushed in all the way.
c Use two fingers with firm, even pressure to push down on the memory module. You should hear a click
when the memory is inserted correctly.
Important: Hold the memory module by its edges, and do not touch the gold connectors.
4 Replace the top case. Replace and tighten the 6 screws you removed in step 2.
Downloaded from ManualsNet.com search engine