System air FGT010 User manual

Systemair FGT
Control manual

Content
I. CHANGING LANGUAGE
II. EXTERNAL DISPLEY
III. EXTERNAL SENSORS
IV. CHANGING AIRFLOW
V. CHANGING REGULATION INTO VAV
VI. CHANGING UNIT OPERATION TIME
VII. TURNING OFF THE UNIT
VIII. CHANGING TEMPERATURE REGULATION
IX. CHANGING TEMPERATURE SETPOINTS FOR ROOM EXTRACT
TEMPERATURE OR TEMPERATURE FOR SUPPLY AIR
X. WATER COOLER ACTIVATION
XI. DX COOLING UNIT ACTIVATION
XII. DX HEATING/COOLING UNIT ACTIVATION
XIII. ELECTRIC HEATER ACTIVATION
XIV. SMOKE DETECTOR

INSTRUCTIONS FOR
CHANGING LANGUAGE
CORRIGO CONTROLLER
Basic
FGT010, FGT015, FGT022

2
Contents
1. Search for change language menu .................................................................................................. 3
2. Changing language .......................................................................................................................... 4

3
1. Search for change language menu
Put yourself on the first screen:
Press RIGHT key button for menu:
Again, press the RIGHT key button:
Again, press the RIGHT key button:

4
2. Changing language
Press OK.
With button UP or DOWN you can select your language and when you found language which you like
to have, press OK.
Press LEFT (3x) to go back to first menu.
You can choose between:
English Czech Slovak
Swedish Lithuanian Dutch
Norwegian Estonian Turkish
Danish Hungarian Romanian
German Latvian
French Slovenian
Finnish Spanish
Russian Portuguese
Polish Italian

INSTRUCTIONS FOR
EXTERNAL DISPLEY
-ED-RU-DFO
-ED-TCV
CORRIGO CONTROLLER
Basic
FGT010, FGT015, FGT022

2
Contents
1. Search for Admin access.................................................................................................................. 3
2. Search for communication menu .................................................................................................... 5
3. Wiring diagram of ED-TCV............................................................................................................... 7
4. Wiring diagram of ED-RU-DFO ........................................................................................................ 9
5. Important note .............................................................................................................................. 11

3
1. Search for Admin access
Put yourself on the first screen:
Press DOWN key to enter the menu:
Press DOWN key (4x) to access the menu ''Access rights'':
Press RIGHT key button:
Press RIGHT key button:
Press the OK button to position yourself on ''Enter password''. Please enter the password ''1111''. For
entering the password Press UP key (2x) for value 1. Press RIGHT key for next position and repeat the
process for the password ''1111'':

4
Press OK button and you will be logged in as ''Admin'':

5
2. Search for communication menu
Press LEFT key (2x) to get to the menu:
Press UP key button to position yourself on the menu ''Configuration'':
Press RIGHT key button:
Press DOWN (31x) key button:
Press RIGHT key button:
Press DOWN key button:

6
Press OK button and DOWN key (3x) and it must be set on ''External display'':
Wait at least 10s and press RIGHT key:
Press OK button and press DOWN key depend on which external display you want to connect.
You have 2 option available in menu:
If you want to connect ED-TCV external display, choose ''ED-TCV'':
Or if you want to connect ED-RU-DFO, choose ''ED-RU/RUD'':

7
3. Wiring diagram of ED-TCV

8

9
4. Wiring diagram of ED-RU-DFO

10

11
5. Important note
After you will activate an external display and start using Port 2 of communication on Corrigo
controller, you cannot use communication protocol Modbus RTU via RS-485.
They only left Modbus TCP IP or BacNet communication protocol for SCADA system.

INSTRUCTIONS FOR
EXTERNAL SENSORS
CORRIGO CONTROLLER
Basic
FGT010, FGT015, FGT022

2
Contents
1. Wiring diagram ................................................................................................................................ 3
2. External sensors .............................................................................................................................. 4
3. Wiring of sensors............................................................................................................................. 5
3.1 RCO2-W, room CO2sensor....................................................................................................... 5
3.2 Systemair-2 CO2duct sensor ................................................................................................... 6
3.3 RTF1 PT1000 room temperature sensor ................................................................................. 7
3.4 QPA2002D room air quality VOC sensor ................................................................................. 8
3.5 QPM2102 duct CO2+ VOC sensor ........................................................................................... 9
4. Configuration of system ................................................................................................................ 10
5. Search for UI menu........................................................................................................................ 12
6. Type of sensor ............................................................................................................................... 14
7. Watching values ............................................................................................................................ 15

3
1. Wiring diagram
In FGT Basic there is prepared free terminal block for connecting an external sensor, like: room CO2,
room VOC, duct CO2, duct VOC, room humidity, room temperature sensor etc. You can see free
terminal block on page 8 in wiring diagram.