System air SAVE VSC 100 Installation and user guide

How to replace lters
SAVE-series

PAGE 2
Contents
1. SAVE VSC 100 .............................................. 3
2. SAVE VSR 150/B ........................................... 3
3. SAVE VSR 300/500 ...................................... 3
4. SAVE VTR 100/B........................................... 4
5. SAVE VTR 150/B ........................................... 4
6. SAVE VTR 150/K ........................................... 4
7. SAVE VTR 250/B............................................5
8. SAVE VTR 300/B ...........................................5
9. SAVE VTR 500 .............................................. 6
10. SAVE VTR 700 ............................................ 6
11. SAVE VTC 200 ............................................ 6
12. SAVE VTC 300.............................................7
13. SAVE VTC 500 .............................................7
14. SAVE VTC 700 .............................................7

PAGE 3
1SAVE VSC 100
2SAVE VSR 150/B
3SAVE VSR 300/500
When it’s time to change the shown on the control panel
display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
1. Stop the unit by disconnecting the mains.
2. Remove the lter cover plates.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Remount and fasten the lter cover plates and
connect the unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Remove the lter cover plates.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Remount and fasten the lter cover plates and
connect the unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open and remove the side cover.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted. See note above.
5. Replace and lock the side cover and connect the
unit to mains.
6. Reset the lter time.

PAGE 4
4SAVE VTR 100/B
5SAVE VTR 150/B
6SAVE VTR 150/K
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
1. Stop the unit by disconnecting the mains.
2. Open and remove the side cover.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted. See note above.
5. Close and fasten the side cover and connect the
unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open and remove the side cover.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted. See note above.
5. Close and fasten the side cover and connect the
unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Close and lock the front hatch and connect the
unit to mains.
6. Reset the lter time.

PAGE 5
7SAVE VTR 250/B
8SAVE VTR 300/B
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. To remove the supply air lter loosen the knobs to
remove the lter lock (image shows when lter is hidden).
Only one of the lter locks needs to be removed.
Wiggle the lter and pull it out.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Close and lock the front hatch and connect the
unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Close and lock the front hatch and connect the
unit to mains.
6. Reset the lter time.
1
2
3
4

PAGE 6
9SAVE VTR 500
10 SAVE VTR 700
11 SAVE VTC 200
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Close and lock the front hatch and connect the
unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Remove the front hatch and open side doors.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Close and lock the front hatch and connect the
unit to mains.
6. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Remove old lters and insert new ones. Make sure
lters are not mixed up during the replacement process.
Supply and extract air lters may be dierent.
4. Close and lock the front hatch and connect the
unit to mains.
5. Reset the lter time.

PAGE 7
12 SAVE VTC 300
13 SAVE VTC 500
14 SAVE VTC 700
When it’s time to change the shown on the control panel
display. When this occurs do the following:
When it’s time to change the lters an alarm is shown on the
control panel display. When this occurs do the following:
When it’s time to change the lters an alarm is shown in the
control panel display. When this occurs do the following:
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Remove old lters and insert new ones. Make sure
lters are not mixed up during the replacement process.
Supply and extract air lters may be dierent.
4. Close and lock the front hatch and connect the
unit to mains.
5. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Remove old lters and insert new ones. Make sure
lters are not mixed up during the replacement process.
Supply and extract air lters may be dierent.
4. Close and lock the front hatch and connect the
unit to mains.
5. Reset the lter time.
1. Stop the unit by disconnecting the mains.
2. Open the front hatch.
3. Pull out the lters towards you. Some force may
be needed.
4. Insert the new lters. Make sure that the correct
lter types are inserted.
5. Close and lock the front hatch and connect the
unit to mains.
6. Reset the lter time.

Systemair UAB
Linų st. 101
LT–20174 Ukmergė, LITAUEN
Phone [phone]
Fax [phone]
www.systemair.com