SZKTDZ KT-LCD10H User manual

KT-LCD10H E-Bike Display User Manual
Dear customer, please read this manual before you use KT-LCD10H Display. The manual will guide you use the
instrument correctly to achieve a variety of vehicle control and vehicle status displays.
Functions and Display
Instruments using the structure form of instrument body portion and the operation buttons are
designed separately.
1
UP Button
10
CRUISE
Cruise
2
SW Button
11
PAS
Pas level
3
DOWN Button
12
VOL
Battery voltage
4
Battery capacity indicator
13
THROTTLE
Run sign
5
℃
Environment temperature
14
DST
Trip distance
℉
Environment fahrenheit
ODO
Total distance
6
MOT
Power display
15
Backlight and headlights
7
Km/H
Riding speed(metric)
16
brake display
8
6Km/H push power assist
17
AVS
Average speed
9
TM
Single trip time
MXS
MAX speed
TTM
Total trip time
Operation
1. ON/OFF
Hold button long to turn on the power, and hold long for a second time to turn off
the power. When the motor stops driving and when the e-bike is not used for a consecutive 5
minutes, it will automatically shut down and turn off the motor power supply.
2. Display1
Hold button to start up and enter display .
2.1 Turn on backlight and headlights
Hold long to turn on backlight and headlights (the controller
should have headlight drive output function); hold long again to turn
off the backlight and headlights.
2.2 Assist ratio gear (PAS) switch
Press or to switch 0-5 file gear. Gear 1 is for the minimum
power, gear 5 is for the highest power. Each startup will automatically
restore the gear shutdown last time (the user can set randomly). Gear 0 is
without booster function.
2.3 Km/H assist promotion function
Hold and flashes, the vehicle drives at the speed not more
than 6Km /h. Release button, the function is invalid.
2.4 Display and delete of single data
After power on for 5 seconds, hold and at the same time,
single trip riding time (TM) and single trip distance (DST) flash, press
button , the content of both is cleared. If failed holding the button within
5 seconds, it will automatically return the display interface after 5 seconds,
original content is preserved.
3. Display2
Press button in display 1 to enter display 2.
In the riding mode after 5 seconds, display 2 automatically returns to
display 1, and the original motor power (MOTOR W) display the output of
temperature detection signal).
4. Display 3
Press button in display 2 to enter display 3.
In the riding condition, five seconds later, a single maximum speed (MXS)
display automatically returns to the real riding speed (Km/H).
5. In display 3, press button,and the display will re-enter display 1.
6. Hold button to turn off the display and the power supply of controller.

7. Automatically prompt interface
7.1 Error Code Display Error Code Definition
01＿info Throttle Abnormality
03＿info Motor hall signal Abnormality
04＿info Torque sensor signal Abnormality
05＿info Axis speed sensor Abnormality(only applied to torque
sensor)
06＿info Motor or controller has short circuit Abnormality
Electronic control system failure will display (flashing) fault code. Once the fault was removed,
it automatically exits from the fault code display interface.
General Project Setting
1. Set maximum riding speed
Within power on 5 seconds, hold and at the same time to
enter maximum riding speed Km/H and MXS setting, press button
maximum riding speed flashing, then press or to set the
maximum riding speed (default 25Km/H). Press button to save the
setting, and press to the next parameter settings.
2. Wheel diameter setting
The wheel diameter will be set after finishing setting the maximum
riding speed, press button wheel diameter specifications flashes.
Press or to set the specifications of wheel diameter. Select the
range 5,6,8,10,12,14,16,18,20,23,24,26,27.5,700c,28and 29 inches. Press
button to save and press to go to the next parameter settings.
3. Set the metric units
The metric units will be set after finishing setting wheel diameter,
press button UNT flash. Press or to select the three
metric units of speed, mileage, and ambient temperature in
synchronization.
Display
Metric
Imperial
Riding speed
Km/H
MPH
Total distance
Km
Mil
Environment temperature
℃Temperature
℉Fahrenheit
4. Press button UNT stop flash after metric unit setting is completed. Hold button long
to exit from setting environment of routine projects and save the setting values, returning to
display
5. Exit from routine project setting
All three routine project settings can exit from the setting environment and return to the
display by holding button long after each setting is completed, meanwhile the setting values
are saved.
Under each setting interface, if the button failed holding for more than 1 minute, it will
automatically return to display 1, and the setting value is invalid.
Outline Drawings and Dimensions
1. Dimensions of main instrument body 2. Mounting dimensions of double brackets
3. Wiring diagram