Taco Marine M20-1013A User manual

®LOW PROFILE
ADJUSTABLE SEAT SLIDE
M20-1013A
Tech Support: 800.653.8567 | [e-mail] | tacomarine.com
@tacomarine
Assembly Instructions
Box Includes
Thank you for purchasing the Low Profile Adjustable Seat Slide by TACO Marine.
Since 1959, we have taken great pride in oering the highest-quality products
with excellent customer service. We stand behind our products 100 percent.
Please visit our website tacomarine.com for more detailed information on a
wide variety of products and to register your new accessory for warranty.
•ONE (1) SEAT SLIDE HOUSING ASSEMBLY
•ONE (1) MOUNTING PLATE
•TWO (2) WASHERS
•TWO (2) FASTENERS
Required,
but not included
•EIGHT (8) 1/4” BOLTS
Always check below the surface that
you are drilling into for electrical wires,
tanks, hoses or other items that could be
damaged by your drill bit or screws.
WARNING
MAINTENANCE
The mounting plate and two rails are made with anodized aluminum. This creates a very
hard protective seal on the surface of the aluminum to protect it as much as possible from
pitting. When the anodized coating is broken and raw aluminum is exposed, corrosion will
take place. Avoid damage from abrasive chemicals, knives, gas or impacts that can break
the anodized coating. Always use a mild, non-abrasive soap and lots of fresh water when
cleaning any aluminum product on your boat.
For more information on maintenance, visit tacomarine.com to view TACO Marine’s Stainless
Steel & Aluminum Care Guide.
Install Seat Slide housing assembly to seat using the seat manufacture’s recommended hardware.
HANDY TIP

®LOW PROFILE
ADJUSTABLE SEAT SLIDE
M20-1013A
Tech Support: 800.653.8567 | [e-mail] | tacomarine.com
@tacomarine
1. Un-package the Seat Slide and place on a
stable surface.
2. Attach the mounting clamp through the
boat seat base using 1/4” countersunk
bolts, washer and nuts.
3. Align Seat Slide so the bottom slots are
aligned with the holes in the bottom of
the seat.
NOTE: Ensure that the Seat Slide
Activation Handle is facing toward the
front of the seat.
4. Attach the Seat Slide to the Seat with 1/4”
bolts and washers, as shown.
NOTE: Tighten these by hand snuggly,
as the next step will require exact
alignment.
INSTALL INSTRUCTIONS
Faces
toward seat
back
Slide
Activation
Handle
Slot aligned
with Seat
Holes
Bolts and
washers

®LOW PROFILE
ADJUSTABLE SEAT SLIDE
M20-1013A
Tech Support: 800.653.8567 | [e-mail] | tacomarine.com
@tacomarine
INSTALL INSTRUCTIONS
5. Activate the Seat Slide Handle and move
the Slide Plate away from the activation
handle.
6. Align Seat Slide so the top slots are
aligned with the holes in the bottom of
the seat.
7. Attach the Seat Slide to the Seat with 1/4”
bolts and washers, as shown. This is the
same process as Step 6.
NOTE: Tighten these down completely
with an Allen wrench.
8. Activate the Seat Slide Handle and move
the Slide Plate forward, as shown. Tighten
the 1/4” bolts completely from Step 4.
Slide
Activation
Handle
Slide Plate
Slot aligned
with Seat
Holes
Bolts and
washers
Bolts and
washers
Slide Plate
Slide
Activation
Handle

®LOW PROFILE
ADJUSTABLE SEAT SLIDE
M20-1013A
Tech Support: 800.653.8567 | [e-mail] | tacomarine.com
@tacomarine
INSTALL INSTRUCTIONS
9. NOTE: For ease of installation, it is
recommended that this step be done as
a team.
Lift the seat and position onto the
Mounting Clamp, as shown. Ensure
that the Seat Slide activation handle is
oriented toward the front of the seat.
NOTE: Mounting Clamp is shown un-
installed for visual representation of
mounting the Seat.
10. Mount the 1/4” bolts and washers to the
assembly using an Allen wrench, as shown
to the right.
NOTE: Seat is not shown installed in the
step.
11. Ensure that the bolts from Step 10 are
completely tightened.
12. Operate the Seat Slide to ensure smooth
operation.
Slide the Seat Slider under the
Mounting Clamp hook end.
Mounting
Clamp
Slide
Activation
Handle
Bolts
Bolts
INSTRUCT-M20-1013A