Tamarack Technologies INFINITY 1100 Cool & Quiet User manual

INFINITY 1100 Cool & Quiet
PRODUCT MANUAL & INSTALLATION GUIDE
Serial Number
______________________
Date of Purchase
______________________
Place of Purchase
______________________
In the Box:
One (1) Infinity Cool & Quiet Fan
One (1) Transition Duct
One (1) Interior Grille
Six (6) Feet of 10" Insulated Duct
One (1) Hanger Assembly consisting of:
Two (2) Bracket/Brace 5"
Four (4) Screw 12 x 1 1/2"
Four (4) Screw ¼-20 x 3/4"
Four (4) Nut ¼-20 with Nylon Insert
Twelve (12) Washer, Flat 1/4"
READ AND SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
·Use this unit in the manner intended by the manufacturer. If you have any questions, contact
the manufacturer.
·Before servicing or cleaning unit, switch power off at service panel and lock service panel to
prevent power from being switched on accidentally. When the service disconnecting cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
·When cutting or drilling into wall or ceiling, do not damage electrical wiring or other hidden
utilities.
·Never place a switch where it can be reached from a tub or shower.
·Do not use this fan over a tub or shower.
·Do not use this fan over cooking appliances.
CAUTION: For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors
CAUTION: This unit has an unguarded impeller. Do Not Use in Locations Readily Accessible to People or Animals.
320 Main Street / Buzzards Bay, MA 02532
508-759-4660 / 800-222-5932 / Fax [phone]

The Best Location for the Infinity1100 CQ
When selecting fan mounting location, consider the following:
· Mounting the fan as far as possible from the interior air intake or exhaust points will
minimize fan operating noise from being transmitted back through the duct-work.
· The fan location should allow sufficient access for service.
· Allow sufficient room for the damper to swing open.
When selecting interior grille location, consider the following:
·The interior grille should be installed in a central location within your home. Above a central hallway or at
the top of a stairwell will provide the best airflow. If desired, the grille can be mounted vertically.
Installation
DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED. MAKE SURE ELECTRICAL
SERVICE TO THE FAN IS LOCKED IN "OFF" POSITION.
What you will need:
Make sure that you have adequate exhaust area out of your attic. This can be accomplished with a
combination of roof, ridge or gable end vents. The Infinity 1100 CQ requires a minimum of three (3)
square feet of attic exhaust area.
* Drill and Drill Bits *Phillips Head Screwdriver *Drywall Cutter *Caulking *Duct Tape
1) Attach the mounting brackets to the fan with the nuts and bolts provided. The wiring box should be
positioned for easy access.
2) Using the wood screws provided, attach the mounting brackets to a rafter or support beam at the
selected location. The housing must hang plumb to allow the damper to close completely.
3) Install the interior grille.
a) Move any insulation out of the way to expose the sheetrock surface.
b) Using the transition duct as a template, mark the opening into the living area.
c) Remove the sheetrock within the mark with a drywall cutter.
d) Place a bead of caulking around the transition duct flange and place it into the opening. The
caulking will prevent air from travelling between the attic and the living space.
e) From below, position the interior grille to cover the opening. Drill pilot holes through the grille,
through the sheetrock and into the transition duct.
f) With the screws provided, attach the grille to the transition duct, sandwiching the sheetrock in
between.
4) Connect the duct to the inlet collar of the round to square transition duct using clamps or duct tape. It
is recommended that the inner vinyl core of the insulated duct be clamped or taped to the collars and
that the vapor barrier surrounding the insulation be duct taped to the housing.
(cont’d)

5) Bend the duct at a gentle angle, avoiding a sharp 90 degree corner, and slide the duct collar over the
transition duct. Make sure to maintain the 10” diameter of the duct throughout the bend to ensure
proper airflow. Connect the duct to the inlet collar of the fan.
6) Plug the power cord into a 115 Volt switched outlet that has been wired to local codes and standards.
This outlet may be switched from a remote location.
Operation
Important - Be sure at least one window is open when the fan is operating.
1. Turn the wall switch to ON. The fan will start and the damper will open.
2. Turn the wall switch to OFF. The fan will stop and the damper will close.
When the fan rotation has slowed the magnet will pull the damper closed.
Care
The motor in The Infinity 1100 CQ is permanently sealed and does not require oiling. To keep dirt, dust
and debris from the fan we recommend that you periodically clean the grille from within the living space
and dust the fan blades from within the attic. Please remember to make sure that the fan is OFF before
dusting the fan blades.
Troubleshooting
The most common problem with The Infinity 1100 CQ is caused by incorrect wiring. Verify the switched
outlet has 115 Volts.
Specifications
Electrical Requirements:
Air Flow:
Duct Size:
Duct Collar Length:
Duct Length:
Interior Grille Dimensions:
Transition Duct Dimensions:
Mounting Flange Dimensions:
Overall Dimensions:
Overall Dimensions w/Damper Open:
Unit Weight:
115V, 60Hz, 1.5A
1070 cfm @ .1"Wg
10”
3"with Bead
6 ft.
14"x 14"
10"Dia x 14"Sq x 10"L
14-1/4"x 1-1/2"
16-1/4"W x 16"H x 6-1/4"D
13"
13 lbs.
320 Main Street / Buzzards Bay, MA 02532
508-759-4660 / 800-222-5932 / Fax [phone]

LIMITED WARRANTY If, within the period of three years from the date of purchase, The
INFINITY 1100 CQ (the Product) is defective or malfunctions in normal home use, Tamarack Technologies,
Inc. will repair or replace the Product, at its discretion. Customer is responsible for shipping charges.
CONDITIONS, EXCLUSIONS, AND LIMITATIONS
This Warranty is subject to the following conditions, exclusions and limitations:
THIS WARRANTY DOES NOT COVER PROBLEMS RESULTING FROM INSTALLATION, OPERATION OR
MAINTENANCE THAT HAS BEEN UNDERTAKEN OTHER THAN IN ACCORDANCE WITH THE INSTRUCTIONS.
THIS WARRANTY DOES NOT COVER PROBLEMS RESULTING FROM DEFECTS IN OR CAUSED BY
ASSOCIATED EQUIPMENT (FURNACES, SOLARIA, ETC.); FROM REPAIRS OR MODIFICATIONS ATTEMPTED
BY PERSONS OTHER THAN TAMARACK TECHNOLOGIES, INC.; FROM ABUSE, ACCIDENTAL OR SHIPPING
DAMAGE OR ACTS OF GOD. THIS WARRANTY DOES NOT APPLY TO THE PRODUCT USED OUTSIDE THE
UNITED STATES, ITS TERRITORIAL POSSESSIONS, AND CANADA. EXCEPT AS SET FORTH ABOVE, NO
EXPRESS OR IMPLIED WARRANTY IS GIVEN OR AUTHORIZED BY TAMARACK TECHNOLOGIES, INC. AND
ALL OTHER SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. ANY WARRANTY OR MERCHANTABILITY OF
FITNESS FOR ANY PARTICULAR PURPOSE SHALL BE LIMITED TO THE WARRANTY HEREUNDER.
MOREOVER, ANY LIABILITY OF TAMARACK TECHNOLOGIES, INC. FOR THE PRODUCT SHALL BE LIMITED
TO THE REPLACEMENT VALUE OF THE PRODUCT. IN NO EVENT SHALL TAMARACK TECHNOLOGIES, INC.
BE LIABLE FOR ANY INCIDENTAL DAMAGES OR FOR ANY CONSEQUENTIAL PROPERTY OR COMMERCIAL
DAMAGES, IRRESPECTIVE OF THE CAUSE THEREOF, OCCURRING EITHER DURING OR AFTER THE
WARRANTY PERIOD, INCLUDING WITHOUT LIMITATION ANY DAMAGES TO ANY PART OF A BUILDING OR
ITS CONTENTS. NOTE: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT
VARY FROM STATE TO STATE. PROOF OF PURCHASE REQUIRED.
320 Main Street / Buzzards Bay, MA 02532
508-759-4660 / 800-222-5932 / Fax [phone]
INFCQPG.1