Tannoy iQ 18B Owner's manual

iQ 18B
PERFORMANCE DATA AND HARDWARE INFORMATION

NOTES:
Dimensions

Flying
Convenient flying points are provided on the iQ 18B which will allow the optional flying
equipment to be used, as shown in Figure 10a. In the addition to flying the iQ 18B by
itself, it can also be flown in conjunction with Tannoy iQ 10 Mid/High unit. They can
also be configured to be flown double. Please refer to the following sections for more
detailed instructions. A pole mount is also provided for flying a mid/high cabinet in the
air. The optional Eyebolt Set can be used when flying an individual iQ 18B.
The following optional flying kit is available:
1) SR18 Rail Kit
2) SR18/10 Rail Kit
3) JK1 Jointing Kit
4) SCB Beam Kit
5) EBS10 Eyebolt Set
The easy to use system combines flexibility with the highest levels of safety. As with
any flying system, safety can only be guaranteed when all precautions have been
implemented correctly.
NOTE: The installation of this product must be carried out in conformity with
local building codes and standards. If necessary, consult your local safety
standards officer before installing any product. Alternatively, check any laws or
bylaws. Tannoy will not be held responsible for any damage caused by the
improper installation of any flying gear or loudspeaker.
Figure 10a

Flying an iQ 18B
To fly the iQ 18B by itself, the following accessories are required: SR18 Side Rail Kit
and SCB Beam Kit.
The flown system is assembled as shown in Figure 10b. The SR18 side rail kit is
screwed to the side of the cabinet using the screws provided (1). The SCB Beam Kits
are then placed above and below the speaker (2). The Lynch Pin is inserted into the
holes of the side rail kit top and bottom (3) and the Pin folded to secure it in place
(Figure 10c).
Figure 10c
Figure 10b

To fly two iQ 18Bs, the following accessories are required: 2 ×SR18 Side Rail Kit, 2 ×
SCB Beam Kit and 1 × JK1 Jointing Kit.
The flown system is assembled as shown in Figure 10d. The SR18 side rail kit is
screwed to the side of each cabinet using the screws provided (1). The JK1 Jointing Kit
is slotted between two SCB Beam Kits for both the top and bottom (2). The combined
SCB Beam Kits are placed above and below the speaker (3). The Lynch Pin is inserted
into the holes of the side rail kit top and bottom (4) and the Pin folded to secure it in
place (Figure 10c, page 10).
Figure 10d

To fly the iQ 18B with the iQ 10 Mid/High unit (with optional trapezoidal cabinet), the
following accessories are required: SR18/10 Side Rail Kit and SCB Beam Kit.
The flown system is assembled as shown in Figure 10e. First, the SR18/10 side rail kit
is screwed to the side of both the iQ 18B and iQ 10 cabinets using the screws provided
(1). The SCB Beam Kits are placed above and below the speaker assembly (2). The
Lynch Pin is inserted into the holes of the side rail kit top and bottom (3) and the Pin
folded to secure it in place (Figure 10f).
Figure 10f
Figure 10e

To fly double combined iQ 18B with the iQ 10 Mid/High unit (with optional trapezoidal
cabinet), the following accessories are required: 2 ×SR18/10 Side Rail Kit, 2 ×SCB
Beam Kit and JK1 Jointing Kit.
The flown system is assembled as shown in Figure 10g. First, the SR18/10 side rail kit
is screwed to the side of each iQ 18B and iQ 10 cabinet using the screws provided (1).
The JK1 Jointing Kit is slotted between two SCB Beam Kits for botht he top and bottom
(2). The combined SCB Beam Kits are placed above and below the speaker assemblies
(3). The Lynch Pin is inserted into the holes of the side rail kit top and bottom (4) and
the Pin folded to secure it in place (Figure10f, page 12).
Figure 10g

Anechoic Frequency Response, with TDX2 Controller
Impedance Response, Passive

Frequency Response 46.8-227Hz
Recommended Amplifier Power 400 -800 watt / 8 ohm
Power Handling Average (2) Programme Peak (10ms)
400 watt 800 watt 1600 watt
Sensitivity (1)
2.83 volt @ 1m (20-180Hz) 95dB 98dB (half space)
Maximum SPL (3) AveragePeak
@ 1m 121dB 127dB
Impedance Nominal 8.0Ω
Minimum 7.0Ω
Distortion
10% Full Power 2nd Harmonic 3rd Harmonic
100 Hz 1.91% 0.59%
250 Hz 0.78% 1.11%
1% Full Power 2nd Harmonic 3rd Harmonic
100 Hz 0.56% 0.47%
250 Hz 0.37% 0.47%
Driver Complement 1 x 18”
Crossover Point Active: Recommended points
20-180 Hz, 24dB/octave, Linkwitz –Riley;
Gain: +5dB
Enclosure Trapezoidal folded horn 18mm birch plywood
Finish Textured black/grey paint
Connectors 2 x Speakon™ NL4MP –in/out
Fittings M8 flying inserts
Accessories SR18 Flying Kit, SR1810 Flying Kit, SCB
Beam Kit
Dimensions 960mm (H) ×630mm (W) ×520mm (D)
37.82” (H) ×24.82” (W) ×20.49” (D)
Weight 52 kg
115 lb
Shipping Dimensions 1040mm (H) ×700mm (W) ×590mm (D)
41” (H) ×27.6” (W) ×23.2” (D)
Shipping Weight 55 kg
121 lb
NOTES: (1) Average over stated bandwidth. Measured at 1m on axis, in an anechoic chamber.
(2) Long term power handling capacity as defined in EIA standard RS -426A.
(3) Unweighted pink noise input, measured at 1m
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing
methods will always equal or exceed the published specifications which Tannoy reserve the right to alter without prior
notice.
Please verify the latest specifications when dealing with critical applications

iQ 18B Service Parts and Accessories
Part Number Description
7900 0954 Driver Kit Type 4504
7900 0955 Recone Kit Type 4504
8001 2070 SR 18 Side Rail Kit
8001 2080 SR 18/10 Side Rail Kit
8001 2090 JK1 Jointing Kit
8001 2180 SCB Single Cabinet Beam
8001 2190 EBS10 Eyebolt Set
8000 0727 TDX2 Digital loudspeaker management system 60-250V -UK
8000 0728 TDX2 Digital loudspeaker management system 60-250V -EUR
8000 0729 TDX2 Digital loudspeaker management system 60-250V -USA
Warranty
No maintenance of the PowerDual™ iQ 18B loudspeaker is necessary.
All Tannoy professional loudspeaker products are covered by a 5-year warranty from the
date of manufacture subject to the absence of misuse, overload or accidental damage.
Claims will not be considered is the serial number has been altered or removed. Work
under warranty should only be carried out by a Tannoy Professional dealer or service
agent. This warranty in no way affects your statutory rights. For further information,
please contact your dealer or distributor in your country. If you cannot locate your
distributor, please contact Customer Services, Tannoy Ltd at the address given below.
Customer Services
Tannoy Ltd.
Coatbridge
ML5 4TF
Scotland
Telephone: [phone] (National)
[phone] (International)
Fax: [phone] (National)
[phone] (International)
E-Mail: [email protected]
Website: www.tannoy.com
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
Our policy commits us to incorporating improvements to our products through
continuous research and development. Please confirm current specifications for critical
applications with your supplier.
EASE Data for Tannoy Professional products available on request.