Tansun Quartzheat SORRENTO IP SINGLE SOR 210IP User manual

©Tansun Limited 2008 Part No. 042220 Issue. 1
F o l l o w i n g i n f o r m a t i o n i s o n l y f o r E U - m e m b e r s t a t e s :
The use of this symbol indicates that this product may not be treated as household aste. By ensuring this
product is disposed of correctly, you ill help prevent potential negative consequences for the environment
and human health, hich could other ise be caused by inappropriate aste handling of this product. For
more detailed information about recycling of this product, please contact your local council, your household
aste disposal service or the shop here you purchased the product.
Fig. S Fig. T
7. Remove the scre (Fig. T) from the side reflector and lift it up a ay from the heater to remove it. Repeat at opposite end to remove
other side reflector.
8. The lamp the ires should be pulled out of the side slots and the lamp can be lifted up completely (Fig. U). The ires should be
gently pulled so they come out from behind the reflector.
9. The lamp should no be removed from the heater as sho n in Fig. V.
10. Refit the ne lamp in reverse order ensuring that no ires get trapped and all scre s are fully tightened.
Fig. U Fig. V
Reference Manual
Sorrento IP
Single
UK & EUROPEAN MODELS:
SOR 210IP, SOR 210IP UK, SOR 210IP EU,
SOR 215IP, SOR 215IP UK, SOR 215IP EU,
SOR 220IP, SOR 220IP UK, SOR 220IP EU.
Spectrum House, Unit 1, Ridgacre Road, West Brom ich,
West Midlands, B71 1BW, England.
Tel: [phone] - Fax: [phone]
Email: [email protected] - Website: .tansun.com

R i s k o f F i r e
Keep combustible materials such as furniture, papers, clothes and curtains at least 1.8m (6 feet) from the front of the heater and
a ay from the sides and rear. If the heater is to be used outside, e recommend that a aterproof or indoor socket is used.
2
I n t r o d u c t i o n
The Sorrento IP heater produces radiant heat like the sun, arming people and objects rather than the air in bet een. It is mounted on an
adjustable bracket that allo s the heat to be directed exactly here it is required. Its attractive, light eight design means that it is effective yet
unobtrusive. The Sorrento IP heater is designed for indoor and outdoor use so is therefore eatherproof.
Please read the following instructions carefully before use. he safety of this heater is guaranteed only by its correct usage in
accordance with these instructions, therefore it is recommended that they are retained for future reference.
S p e c i f i c a t i o n
a b l e 1 . U K a n d E u r o p e a n H e a t e r s
Use MCB Type 3.
C a u t i o n
Before using this appliance:
 Check that the voltage indicated on the type plate corresponds to the mains supply voltage.
 Do not locate the heater immediately belo a socket outlet.
 Ensure that the heater has been securely fastened in its final mounting position.
 Remove the plug from the mains socket (or disconnect pole s itch) during installation, cleaning and/or replacing the
emitter and al ays ensure that the emitter is cool.
 Do not handle the halogen emitter ith bare hands. If it is inadvertently touched, remove finger marks ith a soft
cloth and methylated spirit or alcohol. Other ise, the marks ill burn into the quartz emitter causing premature heater
failure.
 Do not use an extension cable ith this product.
 Keep the mains cable a ay from the body of the heater hich ill get hot during use.
 Do not cover or obstruct the heater hile it is in use.
 The heater is not intended for use by young children or infirm persons unless they have been adequately supervised
by a responsible person to ensure that they can use the heater safely.
 Do not insert any object through any slot or opening in the heater.
 Do not use if guard is not present.
 Do not install less than the minimum mounting distance from the floor.
 Warning - this appliance must be connected to a supply that is earthed!
C o n f i g u r a t i o n s
The Sorrento IP heater is a single lamp unit - it has one lamp. It can be installed as a single unit or joined to one or t o more single units. It
is supplied ith joining bars that connect the heaters together to increase the size and output of the installation. The maximum number of
single units that can be joined together is three. Please read the section ‘assembling’ for information on ho this should be done.
Model Voltage Lamps x otal Current otal Min. height Min. dist. Min. dist. Dimensions (inc. Weight Ingress
x No. of (V) Power Power (A) per Current (A) from floor from ceiling from side bracket & bars max. (kg) Protection
Units (kW) (kW) lamp of unit (m) (m) wall (m) pos.) W x H x D (mm) (IP)
SOR 210IP x 1 230 1 x 1.0 1.0 4.3 4.3 2.0 0.3 1.0 430 x 228 x 323 3.4 IP24
SOR 215IP x 1 230 1 x 1.5 1.5 6.5 6.5 2.0 0.3 1.0 430 x 228 x 323 3.4 IP24
SOR 220IP x 1 230 1 x 2.0 2.0 8.7 8.7 2.0 0.3 1.0 430 x 228 x 323 3.4 IP24
SOR 210IP x 2 230 2 x 1.0 2.0 4.3 8.7 2.0 0.5 1.0 430 x 460 x 402 6.8 IP24
SOR 215IP x 2 230 2 x 1.5 3.0 6.5 13.0 2.0 0.5 1.0 430 x 460 x 402 6.8 IP24
SOR 220IP x 2 230 2 x 2.0 4.0 8.7 17.4 2.0 0.5 1.0 430 x 460 x 402 6.8 IP24
SOR 210IP x 3 230 3 x 1.0 3.0 4.3 13.0 2.5 0.5 1.0 430 x 693 x 402 10.2 IP24
SOR 215IP x 3 230 3 x 1.5 4.5 6.5 19.6 2.5 0.5 1.0 430 x 693 x 402 10.2 IP24
SOR 220IP x 3 230 3 x 2.0 6.0 8.7 26.1 2.5 0.5 1.0 430 x 693 x 402 10.2 IP24
I n s t a l l a t i o n - A l l C o n f i g u r a t i o n s
 Warning - this appliance must be connected to an earthed supply.
 The ired versions (210 UK, 210 EU, 215 UK, 215 EU, 220 UK & 220 EU) are fitted ith 5 metres of supply cable and a moulded plug,
therefore it is unnecessary to remove the terminal box in order to carry out normal installation of these models.
 All un ired versions (210, 215 & 220) should be installed by a suitably qualified electrician, follo ing the instructions belo .
 All installations must be in accordance ith the latest I.E.E safety regulations or equivalent.
 We recommend using a RCD here applicable.
 If self iring, a large double pole s itch ith a 3mm contact disconnection should be fitted.
 If the supply cord becomes damaged, it must be replaced by the manufacturer, its service agent or a similar qualified person in order to
avoid a hazard.
 Please observe the minimum safe distance bet een the heater body and any inflammable surfaces.
M a i n t e n a n c e
In the event of heater failure, or for spare parts or advice, please contact the manufacturer in the first instance.
 Disconnect from the mains before commencing any maintenance procedure including cleaning.
 To ensure optimum heat effectiveness, it is recommended that that the guard is removed and the reflector is iped ith a lint-free cloth should
the reflector sho considerable signs of dust or dirt.
H a n d l i n g t h e R e p l a c e m e n t L a m p
Your ne lamp should not be handled ith bare hands.
Remove finger marks ith a soft cloth and methylated spirits or alcohol. Finger marks ill burn into quartz causing premature lamp failure.
Y o u r R e p l a c e m e n t L a m p
It is very important that your replacement lamp is exactly the same as the one it as supplied ith. Failure to fit the exact same type could cause
the heater to fail or even become dangerous especially hen used in an outdoor environment.
Please contact Tansun Limited to purchase your replacement lamp and state the model number of the heater you ish to fit the lamp to.
7
R e p l a c i n g t h e L a m p
If you are in any doubt about following the procedure below, please contact us for technical assistance. he mains power should be
disconnected before any attempts are made to replace the lamp. he following should be carried out with compliance to the latest IEE
regulations. If you are unfamiliar with installing such fixtures, contact a qualified electrician to carry out.
1. Ensure the heater and lamp are cool and the po er supply is disconnected by removing the plugs from the socket outlet - both plugs must be
removed even if only one lamp is to be replaced.
2. Remove the scre s from the terminal box at the back of the lamp you ish to replace and lift off the lid - see Fig. N.
3. Disconnect the lamp from the connector blocks by unscre ing the scre s highlighted above in Fig. P and remove the hite coloured lamp
ires from the terminal block.
4. At the back of the heater, remove the plate holding the terminal box by removing the t o fixing scre s as sho n in Fig. Q.
Fig. N Fig. P
5. Pull the lamp ires one at a time through the plate to remove as sho n in Fig. R.
6. At the front of the heater, the guard in front of the lamp you are replacing should be removed by gently pulling it a ay from the heater so it
prises out of its locating holes at each end (Fig. S).
Fig. Q Fig. R

6
 Please refer to Table 1 for the recommended positioning of the heater ith regards to minimum
distances. Do not install the heater in a corner!
 Keep out of the reach of children.
1. Securely fasten the L-shaped all brackets to the mounting surface using both of the fixing
holes in the short part of the bracket (see Fig. L for mounting hole centres). Please refer to
Table 1 for recommended positioning of the heater. Please note. all fixings are not
supplied. They should be selected to substantially support the eight of the installation. If in
doubt contact a professional for advice!
2. The heater assembly should be mounted ith the terminal boxes at the bottom of the heaters.
3. Fix the heater assembly to the brackets via the bolt threads on the middle heater. A serrated
asher should be placed on the threads first and the all brackets should prise apart in order
to fit the threads in place.
4. Place a asher and a nut on the thread on the outside of the all brackets – both sides.
5. Fully tighten the nut and bolts ith the heater set at the desired angle.
6. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the angular position.
Fig. K
Fig. L
C e i l i n g H a n g i n g - h r e e S i n g l e H e a t e r s J o i n e d
 When three Sorrento IP heaters are joined they should only be hung from a ceiling on chains - do not all mount!
 Al ays allo the heater to cool before attempting to reposition/move. Never attempt to move the heater hile it is s itched on!
 Observe the minimum safe distance bet een the heater body and inflammable surfaces and objects hen mounting.
 Please refer to Table 1 for the recommended positioning of the heater ith regards to minimum distances. Do not install the heater in a corner!
 Keep out of the reach of children.
1. Please refer to Table 1 for recommended positioning of the heater. When hanging from a ceiling four chains of equal length and gauge
are required and should be selected ith fixings that are more than adequate to hold the eight of the heater. If in doubt contact a professional
for advice!
2. Fix the heater assembly to the chains via the hole in the centre of the joining bars as sho n in Fig. M. and ensure the heater faces directly
do n hen hanging.
3. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the position.
Fig. M
3
Fig. A
Fig. D
Fig. C
Fig. E
M o u n t i n g - S i n g l e U n i t
 The Sorrento IP heater can be all mounted in a horizontal manner or vertical manner or hung from a
ceiling from chains (not supplied).
 When all mounting the Sorrento IP heater in a horizontal manner, do not position the heater at an
angle more than 90° and less than 30° as sho n in Fig. A.
 When vertically mounting the Sorrento IP heater, ensure the mounting surface is angled so the heater
projects do n ards - see Fig. C. Do not position the heater at an angle more than 45° and less than
30° to the horizontal as sho n. Position the heater so the cord is exiting the terminal box pointing
do n.
 When ceiling hanging the Sorrento IP heater, ensure the minimum distance from the ceiling is adhered
to as sho n in Fig. B.
 Al ays allo the heater to cool before attempting to reposition/move. Never attempt to move the
heater hile it is s itched on!
 Observe the minimum safe distance bet een the heater body and inflammable surfaces and objects
hen mounting.
 Please refer to Table 1 for the recommended positioning of the heater ith regards to minimum dis-
tances. Do not install the heater in a corner!
 Keep out of the reach of children.
1. When all mounting, securely fasten the L-shaped all brackets to the mounting surface
using both of the fixing holes in the short part of the bracket (see Fig. E for mounting hole
centres). Refer to Table 1 for recommended positioning of the heater. Please note. all fixings are
not supplied. They should be selected to substantially support the eight of the installation. If in
doubt contact a professional for advice! When hanging from a ceiling t o equal length and gauge
chains are required and should be selected ith fixings that are more than adequate to hold the
eight of the heater. Again, if in doubt contact a professional for advice!
Continued over page...
Fig. B
 When the electrical connection is outside, it is recommended that a aterproof
socket is used for the connection/terminal. Other ise, the plug should be connected
to a socket indoors.
 If in any doubt, please contact a suitably qualified electrician.
1. Unscre the terminal box cover at the back of the heater and feed the supply cable
through the compression gland ensuring the rubber seal is on the cable.
2. Use a minimum of 1.0mm
2
H05RN-F supply cable ith 2 poles and earth and sleeve
ith silicon glass fibre braided (250°C) Sleeving. The live and neutral ires must be
connected to the terminal block. See Fig 1.
3. The green/yello ire should be connected to the clamp marked ith the earth symbol using a
suitable ire terminal. Fit cord grip and terminal box saddle once ired.
4. Tighten the barrel nut of the compression gland so that the rubber seal grips the cable (Fig 2).
5. To prevent ater ingress, ensure that the cover is secured ell by hand tightening all for scre s
evenly.
N
L
Fig. 1
Fig. 2
E

A s s e m b l i n g - w o S i n g l e H e a t e r s J o i n e d
1. Take the first heater and place it face do n on a flat surface.
2. Take the second heater and place it face do n and positioned parallel to the first heater.
3. Push the M8 bolts (used to hold the all brackets through the hole in the brackets on the rear heaters and slide a shake-proof asher on all
the threads from the protruding side.
4. Slide the joining bars on each bolt and fit a asher and nut – do not fully tighten at this point.
5. Ensure the second heater is still parallel to the first and sitting flat.
6. Slide the joining bars on each protruding bolt of the other heater to connect them together and fit the ashers and nuts.
7. Again, ensuring the heaters remain flat, fully tighten all four nuts to secure the joining bars in place.
W a l l M o u n t i n g - w o S i n g l e H e a t e r s J o i n e d
 When t o Sorrento IP heaters are joined together they can be mounted in a horizontal or vertical
manner as the emitter is a universal burning type.
 When all mounting t o Sorrento IP heaters joined together in a horizontal manner, do not position
the heater at an angle more than 45° and less than 10° as sho n in Fig. F.
 When vertically mounting t o Sorrento IP heaters joined together, ensure the mounting surface is
angled so the heater projects do n ards - see Fig. C on Page. 3. Do not position the heater at an
angle more than 45° and less than 30° to the horizontal as sho n. Position the heater so the cords
are exiting the terminal box pointing do n.
 Al ays allo the heater to cool before attempting to reposition/move. Never attempt to move the
heater hile it is s itched on!
 Observe the minimum safe distance bet een the heater body and inflammable surfaces and
objects hen mounting.
 Please refer to Table 1 for the recommended positioning of the heater ith regards to mini-
mum distances. Do not install the heater in a corner!
 Keep out of the reach of children.
1. Securely fasten the L-shaped all brackets to the mounting surface using both of the fixing
holes in the short part of the bracket (see Fig. H for mounting hole centres). Please refer to
Table 1 for recommended positioning of the heater. Please note. all fixings are not
supplied. They should be selected to substantially support the eight of the installation. If in
doubt contact a professional for advice!
2. Fix the heater assembly to the brackets via the hole in the centre of the joining bar. The joining
bars should slide inside the gap of the t o all brackets.
3. Place a bolt and asher in the hole of the all bracket and put a serrated asher on the
opposite side bet een the bracket and joining bar. Repeat on opposite side.
4. Fit the heater assembly to the brackets and place a asher and nut on the bolts protruding
through the joining bars.
5. Fully tighten the nut and bolts ith the heater set at the desired angle
(Fig. G).
6. Secure the supply cable so it is not resting on the body or obstructing the
air-vents.
Always isolate the heater from the mains supply when adjusting the
angular position.
Fig. F
Fig. G
Fig. H
4
2. The heater should be mounted ith the terminal box at the bottom of the heater hen being all mounted.
3. When all mounting, fix in the required angular position by tightening the fixing bolts on the brackets at the rear of the heater as sho n in
Fig. D. The heater should face directly do n hen hanging. Ensure that the serrated asher is placed bet een the surface of the all
bracket and the bracket on the heater.
4. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the position.
5
C e i l i n g H a n g i n g - w o S i n g l e H e a t e r s J o i n e d
 When t o Sorrento IP heaters are joined they can be hung from a ceiling from chains.
 Al ays allo the heater to cool before attempting to reposition/move. Never attempt to
move the heater hile it is s itched on!
 Observe the minimum safe distance bet een the heater body and inflammable
surfaces and objects hen mounting.
 Please refer to Table 1 for the recommended positioning of the heater ith regards to
minimum distances. Do not install the heater in a corner!
 Keep out of the reach of children.
1. Please refer to Table 1 for recommended positioning of the heater. When
hanging from a ceiling t o chains of equal length and gauge are required and
should be selected ith fixings that are more than adequate to hold the eight of
the heater. If in doubt contact a professional for advice!
2. Fix the heater assembly to the chains via the hole in the centre of the joining bar as
sho n in Fig. J. and ensure the heater faces directly do n hen hanging.
3. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the position.
Fig. J
A s s e m b l i n g - h r e e S i n g l e H e a t e r s J o i n e d
1. Take the first heater and lie it face do n on a flat surface.
2. Take the second and third heaters and position them face do n and parallel to the first.
3. Push the M8 bolts (used to hold the all brackets through the hole in the brackets on the rear heaters and slide a shake-proof asher on all
the threads from the protruding side.
4. Slide the joining bars on each bolt and fit a asher and nut – do not fully tighten at this point.
5. Position the second heater so it’s parallel to the first and sitting flat.
6. Take the third heater and a joining bar. Push a bolt and asher through the end hole and place a serrated asher on the other side. Push
the bolt through the bracket hole on heater. Repeat on opposite side and secure ith a asher and nut – do not fully tighten at this point.
7. Position the third heater so it’s parallel to the second.
8. Line-up the bars of the first heater ith the brackets of the second heater – they should go on the inside faces like heater one.
9. Line-up the bars of the third heater ith the brackets of the second heater – these should go on the outside faces like heater three.
10. Push a bolt from the back of the joining bars through the holes putting a serrated asher on each side of the heater bracket.
11. Fit a asher and nut to both sides and providing the assembly is sitting flat, fully tighten both sides and also the nuts of the first and third
heaters to the joining bars.
12. The heater is no ready for mounting or hanging.
W a l l M o u n t i n g - h r e e S i n g l e H e a t e r s J o i n e d
 When three Sorrento IP heaters are joined together they can be mounted in a horizontal or vertical manner as the emitter is a universal burning
type.
 When all mounting three Sorrento IP heaters joined together in a horizontal manner, do not position the heater at an angle more than 80° and
less than 60° as sho n in Fig. K.
 When vertically mounting three Sorrento IP heaters joined together, ensure the mounting surface is angled so the heater projects do n ards -
see Fig. C on Page. 3. Do not position the heater at an angle more than 45° and less than 30° to the horizontal as sho n. Position the heater so
the cords are exiting the terminal box pointing do n.
 Al ays allo the heater to cool before attempting to reposition/move. Never attempt to move the heater hile it is s itched on!
 Observe the minimum safe distance bet een the heater body and inflammable surfaces and objects hen mounting.