Targus Wireless RF Mouse User manual

BRUSSELS HANNOVER BARCELONA TOKYO MILANO AMSTERDAM SINGAPORE LONDON PARIS NEW YORK LOS ANGELES TORONTO HONG KONG SYDNEY
Wireless RF Mouse
USER’S GUIDE
Making Your Mobile Life Easier.
Making Your Mobile Life Easier.
Visit our Web site at: www.targus.com
Features and specifications are subject to change without notice. ©2003 Targus Corp.
400-0120-001B

2
TARGUS WIRELESS RF
MOUSE
Introduction
Congratulations on your purchase of a Targus Wireless RF
Mouse. This ergonomically designed mouse uses a radio
frequency (RF) link that enables you to use the mouse
anywhere within three feet of its receiver. No line-of-sight
between the mouse and its receiver is required.
This user’s guide describes how to connect the mouse receiver
to your computer, install default software drivers and set up the
radio link.
System Requirements
To use the RF mouse, your computer must meet the following
hardware requirements and run one of the operating systems
listed below.
Hardware
•PCwithanIntel
®Pentium®processor or equivalent and a
hard disk drive
• USB interface
Operating System
• Windows®98/Me/2000/XP
NOTE: The third button and the scrolling wheel only work with
the operating systems listed above. If you use the RF mouse
with a different operating system, it will lose its enhanced
features and function as a standard, two-button mouse.

3
Targus Wireless RF Mouse
Installing the Batteries
1 Remove the battery cover from the top of the mouse by
pressing the battery cover hinge, located on the bottom of
the mouse, and sliding it off.
Removing the battery cover
2 Insert the supplied batteries, making sure that the positive
(+) and negative (-) ends of each battery match the polarity
indicators inside the battery housing.
WARNINGS: When replacing the batteries, you may use
alkaline or other heavy-duty NiMH batteries. Never combine
an alkaline with a NiMH battery in a device.
Avoid mixing new and used batteries in a device.
3 Slide the battery cover back into position until it “clicks”
firmly into place.
Battery cover hinge
Battery cover

4
Targus Wireless RF Mouse
Using the Charger Base
For best results, you should charge the RF mouse for at least
four hours before using the mouse.
NOTE: Using the charger base is optional. If you are using the
mouse without the charger base, you may use disposable
batteries.
CAUTION: If you are using the mouse with the charger base,
you must use rechargeable batteries, such as the ones
supplied, to avoid possible damage to the mouse and charger.
To set up the charger base and charge your mouse:
1 Make sure that batteries in the RF mouse are properly
installed.
2 Attach the power adapter to the power jack on the charger
base and plug the power adapter into a power strip or wall
outlet.
3 Place the RF mouse into the charger base.
The status light on the charger base glows while it charges
the mouse’s batteries.
Connecting the Mouse Receiver
To connect the mouse receiver:
1 Turn off your computer.
2 Plug the USB receiver into an available USB port on your
computer.

5
Targus Wireless RF Mouse
Installing the Device Drivers
Windows®98/Me Operating Systems
1 Turn on your computer.
The Add New Hardware Wizard appears.
If it does not, the operating system has installed the default
driver automatically. No other steps are necessary.
2ClickNext.
The locate driver screen appears.
3SelectSearch for the best driver for your device.
(Recommended) and then click Next.
The wizard searches for the appropriate device driver.
4ClickNext, then Finish to complete the driver installation.
You are now ready to set the radio frequency channel and
establish a communications link between the mouse and its
receiver. See “Establishing a Communications Link” on page 6
Windows®2000/XP Operating Systems
1 Turn on your computer.
The Found New Hardware Wizard appears.
If it does not, the operating system has installed the default
driver automatically. No other steps are necessary.
2ClickNext.
The wizard searches for the appropriate device driver.
3ClickNext, then Finish to complete the driver installation

6
Targus Wireless RF Mouse
You are now ready to set the radio frequency channel and
establish a communications link between the mouse and its
receiver. See “Establishing a Communications Link” on page 6
Establishing a Communications
Link
After your computer detects the USB receiver and the driver
software is installed, you must establish a communications link
between the mouse and its receiver BEFORE you can use the
mouse. To establish this link, you need to set the identification
code so that the mouse works properly.
Setting the Identification Code
Make sure that your computer is turned on and has detected the
USB receiver before you establish a communications link.
1 Press and release the link button on the receiver.
Sample receiver
The receiver’s status light glows when the receiver is
activated.
2 Press and release the reset button, located on the bottom of
the mouse.
Link button

7
Targus Wireless RF Mouse
CAUTION: Pressing and holding the reset button longer than
1.5 seconds may cause the mouse to enter power off mode.
See “Mouse Power Management” on page 7.
Sample mouse bottom
The mouse’s red light emitter diode (LED) stops glowing
when you press the reset button and resumes glowing when
the button is released.
You are now ready to use the RF mouse.
Mouse Power Management
To power the mouse off, wake the mouse (if it’s in sleep
mode), press and hold the reset button for at least two seconds.
Then, release the reset button when the red LED flashes one
time.
To power the mouse on, press and release the reset button so
that the red LED glows.
Reset button

8
Targus Wireless RF Mouse
Operating Hints
For optimal performance and RF reception:
• Place the receiver at least 8 inches (20 cm) away from all
electrical devices, such as your monitor, speakers or external
storage devices.
If necessary, use a three-inch extension cable to place the
receiver away from the computer. Plug the receiver into the
extension cable, and the extension cable to the computer.
• Avoid using the RF mouse on a metal surface. Metals, such
as iron, aluminum or copper, shield the radio frequency
transmission and may slow down the mouse’s response time
or cause the mouse to fail temporarily.
• The RF mouse will enter a suspend mode at the same time
your computer does. To activate the mouse, press any button.
• If your computer has a metal case that contains aluminum or
magnesium, use the RF mouse to the side. The display panel
may interfere with the radio frequency signal if you use the
mouse directly in front of the computer.
• Never use the RF mouse on a glass or mirrored surface as
these surfaces will cause the mouse to fail temporarily.
• To maximize battery life, use the RF mouse on a white, or
light colored surface. Dark surfaces cause the mouse’s light
emitter diode (LED) light to glow brighter, which causes the
battery to discharge more rapidly.

9
Targus Wireless RF Mouse
Comfortable Usage
Research suggests that physical discomfort and injury to
nerves, tendons, and muscles may be related to repetitive
motion, an improperly set up work area, incorrect body posture
or poor work habits.
To reduce the risk of injury, follow these precautions:
• Stand, stretch, and move around several times every hour.
• Switch hands while performing tasks. Use shortcut keys to
avoid repetitive or awkward mouse movements.
• Relax your shoulders and keep your elbows at your sides.
Adjust the keyboard’s position so that you don’t have to
stretch to reach it.
• Adjust your position so that you don’t have to bend your
wrists to type; avoid placing your wrists on a sharp edge.
If you feel discomfort or numbness in your hands, wrists, arms,
shoulders, neck, or back while typing, consult a qualified
medical professional.
Things to Remember
Batteries
General
• You must establish a communications link every time you
change the batteries.
• To extend the life of your batteries, turn off the mouse by
holding the reset button, located on the bottom of the mouse,

10
Targus Wireless RF Mouse
for two seconds. See “Mouse Power Management” on
page 7.
• Always synchronize the mouse and its receiver after
changing the batteries.
Sleep Mode
• The mouse’s sleep mode feature activates after 20 minutes of
non-operation.
• The mouse enters sleep mode every time the batteries are
changed.
• To wake the mouse from sleep mode, press any button.
Specifications
Button Count 3 with scrolling wheel
ID Selections 256
Electromagnetic
Characteristics (EMC)
CE - Type acceptance: ETS 300
220 short range devices
Distance Between
Mouse and Receiver up to 3 feet (1 m)
Mouse Carrier Frequency 27 MHz
Dimensions Mouse:
3.86 x 2.32 x 1.5 inches
(98 x 59 x 38 mm)
Receiver:
1.96 x 0.86 x 0.59 inches
(50 x 22 x 15 mm)