Taylor Wawa C708 User manual

OPERATOR’S 
MANUAL
Model C708
Heat Treatment
Soft Serve Freezer
8/30/12 (Original Publication)
(Updated 7/26/2019)
Original Operating Instructions
080883-M

Complete this page for quick reference when service is required:
Taylor distributor: __________________________________________________________
Address: _________________________________________________________________
Phone: __________________________________________________________________
Service: _________________________________________________________________
Parts: ___________________________________________________________________
Date of installation:_________________________________________________________
Information found on the data label:
Model Number:____________________________________________________________
Serial Number: ____________________________________________________________
Electrical Specs: Voltage__________________ Cycle__________
Phase__________________________________
Maximum Fuse Size: ______________________________________________________ A
Minimum Wire Ampacity: ___________________________________________________ A
Note: Continuing research results in steady improvements; therefore, information in this manual is subject to change
without notice.
Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be
the original set of instructions.
© 2014, Taylor Company
080883-M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be
a violation of copyright law of the United States of America and other countries, could result in the awarding of
statutory damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal
penalties. All rights reserved.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072

Table of Contents
080883-M i
Section 1: To the Installer
Section 2: To the Operator
Section 3: Safety
Section 4: Operator Parts Identification
Model C708 Exploded View Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Model C708 Single Spout Door and Beater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
X45316-B - Pump A.-Coax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Brush A.-Package-HT X44127 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Section 5: User Interface
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Operating Screen Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Freezer Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Manager's Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Section 6: Operating Procedures
Freezing Cylinder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Freezer Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Mix Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Sanitizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10
Daily Closing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Daily Opening Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Manual Brush-Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Draining Product from the Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14
Hopper Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Brush-Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
Section 7: Operator’s Checklist
During Cleaning and Sanitizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Troubleshooting Bacterial Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Regular Maintenance Checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

ii 080883-M
Table of Contents
Section 8: Troubleshooting Guide
Section 9: Parts Replacement Schedule
Section 10: Limited Warranty on Equipment
Section 11: Limited Warranty on Parts

Section 1
1-1
Model C708 - WAWA
To the Installer
1
To the Installer
The following information has been included in the
manual as safety and regulatory guidelines. For complete
installation instructions, please see the Installation
Checklist.
Installer Safety
IMPORTANT! In all areas of the world,
machines should be installed in accordance with existing
local codes. Please contact your local authorities if you
have any questions.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and service
of Taylor®machines.
• Only Taylor service personnel should perform
installation, maintenance, and repairs on Taylor
machines.
• Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the industry
standards on lockout/tagout procedures before
beginning any installation or repairs.
• Authorized service personnel must ensure that
the proper personal protective equipment (PPE)
is available and worn when required during
installation and service.
• Authorized service personnel must remove all
metal jewelry, rings, and watches before
working on electrical equipment.
DANGER! The main power supply(s) to the
machine must be disconnected prior to performing any
installation, maintenance, or repairs. Failure to follow this
instruction may result in personal injury or death from
electrical shock or hazardous moving parts, as well as
poor performance or damage to the machine.
Note: All repairs must be performed by a Taylor service
technician.
WARNING! This machine has many sharp
edges that can cause severe injuries.
Site Preparation
Review the area where the machine will be installed
before uncrating the machine. Make sure that all possible
hazards to the user and the machine have been
addressed.
For Indoor Use Only: This machine is designed to
operate indoors, under normal ambient temperatures of
70°F to 75°F (21°C to 24°C). The freezer has
successfully performed in high ambient temperatures of
104°C (40°C) at reduced capacities.
WARNING! This machine must NOT be
installed in an area where a water jet or hose can be
used. NEVER use a water jet or hose to rinse or clean
the machine. Failure to follow this instruction may result
in electrocution.
WARNING! Only install this machine in a
location where its use and maintenance is restricted to
trained personnel. Failure to comply may result in
personal injury.
CAUTION! This machine must be installed on
a level surface to avoid the hazard of tipping. Extreme
care should be taken in moving this machine for any
reason. Two or more persons are required to safely move
this machine. Failure to comply may result in personal
injury or damage to the machine.
The authorized installer should inspect the machine and
promptly report any damage to the local authorized
Taylor distributor.
This machine is made using USA sizes of hardware. All
metric conversions are approximate and vary in size.

1-2
TO THE INSTALLER
Model C708 - WAWA To the Installer
1
Air-Cooled Machines
Do not obstruct air intake and discharge openings:
The Model C708 requires a minimum of 6 in. (152 mm) of
clearance on both sides and 0 in. in the rear of the
machine.
This will allow for adequate airflow across the
condensers. Failure to allow adequate clearance can
reduce the refrigeration capacity of the freezer and
possibly cause permanent damage to the compressor.
Water Connections
(Water-Cooled Machines Only)
An adequate cold water supply must be provided with a
hand shutoff valve. On the underside of the base pan or
on the right side, two 3/8 in. IPS water connections for
inlet and outlet are provided for easy hookup. Half-inch
inside diameter water lines should be connected to the
machine. (Flexible lines are recommended, if local codes
permit.) Depending on local water conditions, it may be
advisable to install a water strainer to prevent foreign
substances from clogging the automatic water valve.
There will be only one water in and one water out
connection. Do not install a hand shutoff valve on the
water out line. Water should always flow in this order:
first, through the automatic water valve; second, through
the condenser; and third, through the outlet fitting to an
open trap drain.
IMPORTANT! A backflow prevention device is
required on the incoming water connection side. Please
see the applicable national, state, and local codes for
determining the proper configuration.
Electrical Connections
IMPORTANT! In the United States, this
machine is intended to be installed in accordance with
the National Electrical Code (NEC), ANSI/NFPA 701987.
The purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.
In all other areas of the world, the machine should be
installed in accordance with the existing local codes.
Please contact your local authorities if you have any
questions.
Each machine requires one power supply for each data
label on the machine. Check the data label(s) on the
machine for branch circuit overcurrent protection or fuse,
circuit ampacity, and other electrical specifications.
See the wiring diagram provided inside the electrical box
for proper power connections.
WARNING! This machine must be properly
grounded. Failure to do so can result in severe personal
injury from electrical shock.
IMPORTANT! An equipotential grounding lug is
provided with this machine. Some countries require the
grounding lug to be properly attached to the rear of the
frame by the authorized installer. The installation location
is marked by the equipotential bonding symbol (5021 of
IEC 60417-1) on both the removable panel and the
machine's frame.
FOLLOW YOUR LOCAL ELECTRICAL CODES.

TO THE INSTALLER
1-3
Model C708 - WAWA
To the Installer
1
IMPORTANT!
• Stationary machines which are not equipped
with a power cord and a plug or another device
to disconnect the machine from the power
source must have an all-pole disconnecting
device with a contact gap of at least 0.125 in.

(3 mm) in the external installation.
• Machines that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected
or not used for long periods, or during initial
installation, shall have protective devices to
protect against the leakage of current, such as a
GFI, installed by authorized personnel to local
codes.
• Supply cords used with this machine shall be

oil-resistant, sheathed flexible cable not lighter
than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(code designation 60245 IEC 57) installed with
the proper cord anchorage to relieve conductors
from strain, including twisting, at the terminals
and protect the insulation of the conductors from
abrasion.
If the supply cord is damaged, it must be replaced by a
Taylor service technician to avoid a hazard.
Beater Rotation
NOTICE! Beater rotation must be clockwise as
viewed looking into the freezing cylinder.
To correct the rotation on a three-phase machine,
interchange any two incoming power supply lines at the
freezer main terminal block only. To correct rotation on a
single-phase machine, exchange leads inside the beater
motor. (Follow the diagram printed on the motor.)
Electrical connections are made directly to the terminal
block provided in the main control box, located behind
the service panel.
It is recommended that beater rotation adjustment be
performed by an authorized Taylor service technician.
The Model C708 electrical connections are made directly
to the terminal block provided in the main control box
behind the rear panel.
Refrigerant
CAUTION! This machine contains fluorinated
greenhouse gases (F-Gas) to provide refrigeration using
a hermetically sealed circuit or within foam insulation.
This machine’s type of gas, quantity, Global Warming
Potential (GWP), and CO2 tonnes equivalent information
is recorded on the machine’s data label. The refrigerant
used is generally considered nontoxic and
nonflammable. However any gas under pressure is
potentially hazardous and must be handled with caution.
NEVER fill any refrigerant cylinder completely with liquid.
Filling the cylinder to approximately 80% will allow for
normal expansion.
CAUTION! Use only approved refrigerant
listed on the machine's data label or authorized through a
manufacturer's technical bulletin. The use of any other
refrigerant may expose users and operators to
unexpected safety hazards.
WARNING! Refrigerant liquid sprayed onto the
skin may cause serious damage to tissue. Keep eyes
and skin protected. If refrigerant burns should occur,
flush the area immediately with cold water. If burns are
severe, apply ice packs and contact a physician
immediately.
NOTICE! Taylor reminds technicians to be
aware of and in compliance with local government laws
regarding refrigerant recovery, recycling, and reclaiming
systems. For information regarding applicable local laws,
please contact your local authorized Taylor distributor.
IMPORTANT! Refrigerants and their
associated lubricants may be extremely moisture
absorbent. When opening a refrigeration system, the
maximum time the system is open must not exceed 15
minutes. Cap all open tubing to prevent humid air or
water from being absorbed by the oil.

1-4
TO THE INSTALLER
Model C708 - WAWA To the Installer
1
Notes:

Section 2
2-1
Model C708 - WAWA
To the Operator
2
To the Operator
Your freezer has been carefully engineered and
manufactured to give you dependable operation. This
machine, when properly operated and cared for, will
produce a consistent quality product. Like all mechanical
products, it will require cleaning and maintenance. A
minimum amount of care and attention is necessary if the
operating procedures outlined in this manual are followed
closely.
IMPORTANT! This manual should be read
before operating or performing any maintenance on the
machine.
Your Taylor machine will NOT compensate for and/or
correct any errors made during setup or filling operations.
Thus, the initial assembly, setup, and priming procedures
are of extreme importance. It is strongly recommended
that all personnel responsible for the machine's
operation, including assembly and disassembly, go
through these procedures together to be properly trained
and to make sure that all personnel understand their role
in using and maintaining the machine.
If you require technical assistance, please contact your
local authorized Taylor distributor.
Note: Your Taylor warranty is valid only if the parts are
authorized Taylor parts, purchased from the local
authorized Taylor distributor, and only if all required
service work is provided by a Taylor service technician.
Taylor reserves the right to deny warranty claims on
machines or parts if unapproved Taylor parts or incorrect
refrigerant were installed in the machine, system
modifications were performed beyond factory
recommendations, or it is determined that the failure was
caused by abuse, misuse, neglect, or failure to follow all
operating instructions. For full details of your Taylor
warranty, please see the Limited Warranty section in this
manual.
Note: Constant research results in steady
improvements; therefore, information in this manual is
subject to change without notice.
IMPORTANT! If the crossed-out wheeled bin
symbol is affixed to this machine, it signifies that this
machine is compliant with the EU directives as well as
other similar end-of-life legislation in effect after August
13, 2005. Therefore, it must be collected separately after
its use is completed and cannot be disposed as unsorted
municipal waste.
The user is responsible for delivering the machine to the
appropriate collection facility, as specified by your local
code.
For additional information regarding applicable local
disposal laws, please contact the municipal waste facility
and/or local authorized Taylor distributor.

2-2
TO THE OPERATOR
Model C708 - WAWA To the Operator
2
Compressor Warranty Disclaimer
The refrigeration compressor(s) on this machine are
warranted for the term stated in the Limited Warranty
section in this manual. However, due to the Montreal
Protocol and the U.S. Clean Air Act Amendments of
1990, many new refrigerants are being tested and
developed, thus seeking their way into the service
industry. Some of these new refrigerants are being
advertised as drop-in replacements for numerous
applications. It should be noted that in the event of
ordinary service to this machine's refrigeration system,
only the refrigerant specified on the affixed data label
should be used. The unauthorized use of alternate
refrigerants will void your Taylor compressor warranty. It
is the machine owner's responsibility to make this fact
known to any technician he/she employs.
It should also be noted that Taylor does not warrant the
refrigerant used in its machines. For example, if the
refrigerant is lost during the course of ordinary service to
this machine, Taylor has no obligation to either supply or
provide its replacement either at billable or unbillable
terms. Taylor does have the obligation to recommend a
suitable replacement if the original refrigerant is banned,
obsoleted, or no longer available during the 5-year
warranty of the compressor.
Taylor will continue to monitor the industry and test new
alternates as they are being developed. Should a new
alternate prove, through our testing, that it would be
accepted as a drop-in replacement, then the above
disclaimer would become null and void. To find out the
current status of an alternate refrigerant as it relates to
your compressor warranty, call the local Taylor distributor
or the Taylor factory. Be prepared to provide the 
model/serial number of the machine in question.

Section 3
3-1
Model C708 - WAWA
Safety
3
Safety
We at Taylor Company are concerned about the safety of
the operator when he or she comes in contact with the
freezer and its parts. Taylor has gone to extreme efforts to
design and manufacture built-in safety features to protect
both the operator and service technician. As an example,
warning labels have been attached to the freezer to further
point out safety precautions to the operator.
DANGER! Failure to adhere to the following
safety precautions may result in severe personal injury or
death. Failure to comply with these warnings may also
damage the machine and/or its components. Such
damage may require component replacement and
service repair expenses.
NOTICE! DO NOT operate this machine
without reading this entire manual first. Failure to follow
all of these operating instructions may result in damage
to the machine, poor performance, health hazards, or
personal injury.
IMPORTANT! This machine is to be used only
by trained personnel. It is not intended for use by children
or people with reduced physical, sensory, or mental
capabilities or lack of experience and knowledge. Where
limited machine operation is allowed for public use, such
as a self-serve application, supervision or instruction
concerning the use of the machine by a person
responsible for their safety is required. Children should
be supervised to ensure that they do not play with the
machine.
IMPORTANT! An equipotential grounding lug is
provided with this machine. Some countries require the
grounding lug to be properly attached to the rear of the
frame by the authorized installer. The installation location
is marked by the equipotential bonding symbol (5021 of
IEC 60417-1) on both the removable panel and the
machine's frame.
WARNING! DO NOT use a water jet to clean
or rinse the machine. Failure to follow these instructions
may result in serious electrical shock.
WARNING! Avoid injury.
•DO NOT operate the machine unless it is
properly grounded.
•DO NOT operate the machine with fuses larger
than specified on the machine's data label.
• All repairs should be performed by an
authorized Taylor service technician.
• The main power supplies to the machine must
be disconnected prior to performing installation,
repairs, or maintenance.
• Machines that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected
or not used for long periods, or during initial
installation, shall have protective devices to
protect against the leakage of current, such as a
GFI, installed by the authorized personnel to
local codes.
• Stationary machines that are not equipped with
a power cord and a plug or another device to
disconnect the appliance from the power source
must have an all-pole disconnecting device with
a contact gap of at least 0.125 in. (3 mm) in the
external installation.
• Supply cords used with this machine shall be 
oil-resistant, sheathed flexible cable not lighter
than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(code designation 60245 IEC 57) installed with
the proper cord anchorage to relieve conductors
from strain, including twisting, at the terminals
and protect the insulation of the conductors from
abrasion.
• If the supply cord is damaged, it must be
replaced by a Taylor service technician to avoid
a hazard.

3-2
SAFETY
Model C708 - WAWA Safety
3
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
distributor for service.
WARNING! Avoid injury.
•DO NOT allow untrained personnel to operate
this machine.
•DO NOT operate the machine unless all service
panels and access doors are fastened with
screws.
•DO NOT remove any internal operating parts
(including, but not limited to the freezer door,
beater, or scraper blades) unless all control
switches are in the OFF position.
Failure to follow these instructions may result in severe
personal injury, especially to fingers or hands, from
hazardous moving parts.
WARNING! This machine has many sharp
edges that can cause severe injuries.
•DO NOT put objects or fingers in the door
spout. This may contaminate the product and
cause severe personal injury from blade
contact.
•USE EXTREME CAUTION when removing the
beater assembly. The scraper blades are very
sharp.
•USE EXTREME CAUTION when handling the
cup/cone dispenser (if supplied with machine).
Two people are required to handle the cup/cone
dispenser. The appropriate type of protective
gloves must be worn and the mounting holes
must NOT be used to lift or hold the dispenser.
Failure to follow these instructions can result in personal
injury or damage to the machine.
IMPORTANT! Access to the service area of
the machine must be restricted to persons having
knowledge and practical experience with the machine, in
particular as far as safety and hygiene are concerned.
CAUTION! This machine must be placed on a
level surface. Extreme care should be taken when
moving for any reason. Two or more persons are
required to safely move this machine. Failure to comply
may result in personal injury or damage to the machine.
NOTICE! Cleaning and sanitizing schedules
are governed by your federal, state, or local regulatory
agencies and must be followed accordingly. Please refer
to the cleaning section of this manual for the proper
procedure to clean this machine.
CAUTION! This machine is equipped with a
refrigerated cabinet designed to maintain product
temperature at or below 41°F (5°C). Before replenishing
the mix supply, the product must be refrigerated at or
below 41°F (5°C). Failure to follow this instruction may
result in health hazards and poor freezer performance.
DO NOT run the machine without product. Failure to
follow this instruction can result in damage to the
machine.
DO NOT obstruct air intake and discharge openings. A
minimum of 3 in. (76 mm) air clearance on both sides of
the machine is required. It is recommended to place the
rear of the machine against the wall to prevent the
recirculation of warm air. Failure to follow this instruction
may cause poor freezer performance and damage to the
machine.
For Indoor Use Only: This machine is designed to
operate indoors, under normal ambient temperatures of
70°F to 75°F (21°C to 24°C). The machine has
successfully performed in high ambient temperatures of
up to 104°F (40°C) at reduced capacities.
Noise Level: Airborne noise emission does not exceed
78 dB(A) when measured at a distance of 39 in. (1.0 m)
from the surface of the machine and at a height of 62 in.
(1.6 m) from the floor.

Section 4
4-1
Model C708 - WAWA
Operator Parts Identification
4
Operator Parts Identification
Figure 4-1
5
4
68
10
9
3
2
1
11
23
12
13
21 22
16
15 12
20
17
18
12
19 14
7

4-2
OPERATOR PARTS IDENTIFICATION
Model C708 - WAWA Operator Parts Identification
4
Model C708 Exploded View Parts Identification
Item Description Part No.
1 Panel-Side-Left 056963
2 Pan-Drip 11-5/8 Long 027503
3 Pin-Retaining-Hopper CVR 043934
4 Kit A.-Cover-Hopper X65368
5 Blade A.-Agitator X56591
6 Trim-Corner-Rear-Left 056964
7 Pump A.-Coax (See page 4-4) X45316-B
8 Panel-Rear 056077
9 Trim-Corner-Rear-Right 056965
10 Pan A.-Drip 5 1/2” Long X56074
11 Panel A.-Front-Upper X59423
12 Screw-1/4-20 x 3/8 011694
Item Description Part No.
13 Panel A-Side-Right X57869-SER
14 Cart C20100-000
15 Cover-Access-Front R. 056933
16 Filter-Air 052779-9
17 Panel A.-Front-Lower X58955
18 Shelf-Tray-Drip 056076
19 Tray-Drip 056858
20 Shield-Splash 049203
21 Screw 10 x 3/8 Slotted 015582
22 Cover-Access-Left 056946
23 Stud-Nose Cone 055987

OPERATOR PARTS IDENTIFICATION
4-3
Model C708 - WAWA
Operator Parts Identification
4
Model C708 Single-Spout Door and Beater Assembly
Figure 4-2
10
9
8
11
7
12
5
6
4
1
7
3
2
16
15
14 13
Item Description Part No.
1 Handle A.-Draw-Welded X56246
2 O-ring-1/4 OD x .070W 50 015872
3 Screw-Adjustment-5/16-24 056332
4 Valve A.-Draw X55820
5 O-ring-7/8 OD x .103W 014402
6 Baffle A.-Long 4” X50882
7 Kit A.-Beater-Front Shoes-Bearing X50350
8 Beater A.-3.4qt-1 Pin X46231
Item Description Part No.
9 Shaft-Beater 056078
10 Seal-Drive Shaft 032560
11 Blade-Scraper-Plastic 084350
12 O-Ring-4 5/8ODX4 1/4IDX3/16 066019
13 Pin-Handle-SS 055819
14 Door A.-w/Baffle X57332-SER
15 Nut-Stud-Black 2.563 Long 058764
16 Nut-Stud-Black 3.250 Long 058765

4-4
OPERATOR PARTS IDENTIFICATION
Model C708 - WAWA Operator Parts Identification
4
X45316-B - Pump A.-Coax
Figure 4-3
1
23
45
6
7
12
13
6
8
9
16
18
10 18b
18a
17
15
14
11
Item Description Part No.
1 Tube A.-Mix Inlet X45318
2 Seal-Air Inlet Fitting 045327
3 Spring-Tapered 1-7/8L 022456
4 Poppet-Rubber-Black 022473
5 Body A.-Coax Valve X46860-B
6 O-ring-2-1/8 OD x .139W 020051
7 O-ring-1-3/8 OD x .103W #123 018664
8 Piston-Coax Pump 045319-B
9 Pin A.-Coax Pump X36950
10 Cylinder A.-Pump X44755
Item Description Part No.
11 O-ring-3/4 OD x .103W 015835
12 Ring-Check 2 In OD x 1/2 020050
13 Ring-Check 1-1/4 OD x 3/8 033215
14 O-ring-11/16ODX.103W 016132
15 Pin-Cotter-1/8DIA 044731
16 Clip-Retainer-Mix Pump 044641
17 Tube A.-Heat T.Pump Feed X44666
18 Shaft A.-Drive X41947
18a O-ring 1/2 ID x .139W 048632
18b O-ring-1-3/4 OD x .139W 008904

OPERATOR PARTS IDENTIFICATION
4-5
Model C708 - WAWA
Operator Parts Identification
4
Accessories
Figure 4-4
*Note: A sample container of sanitizer is sent with the
machine. For reorders, order Stera-Sheen®part no. 055492
(100 2 oz. packs) or Kay-5®part no. 041082 (200 packs). **Not
Shown
Apply the appropriate
Taylor approved food safe lubricant.
HP
3
1
5
4
2
Item Description Part No.
1 Sanitizer-Stera Sheen *See Note
2 Tool-O-ring Removal 048260-WHT
3 Tool-Shaft-Drive-Pumphopper 057167
4 Lubricant-Taylor Hi-Perf 048232
Item Description Part No.
5 Pail-10 Qt. 013163
** Kit A.-Tune-Up (C708) X49463-8A
** Kit A.-Parts Tray (C708) X51653
** ** Tool-Shaft-Drive Pumphopper/
LVB
047919

4-6
OPERATOR PARTS IDENTIFICATION
Model C708 - WAWA Operator Parts Identification
4
Brush A.-Package-HT X44127
Figure 4-5
1
2
3
4
5
6
8
7
9
10
Item Description Part No.
1Black Bristle Brush 013071
2Double End Brush 013072
3White Bristle Brush 1” x 2” 013073
4White Bristle Brush 1-1/2” x 3” 014753
5White Bristle Brush 1/2 x 3 033059
Item Description Part No.
6Brush-syrup Port 045079
7Brush Set (3) 050103
8Yellow Bristle Brush 039719
9White Bristle Brush 3” x 7” 023316
10 Pump Spout Brush 054068

Section 5
5-1
Model C708 - WAWA
User Interface
5
User Interface
Figure 5-1
Item Description
1 Power Switch
2 Liquid Crystal Display (LCD)
3 Keypads
4 Mix Out Indicator
5 Standby Indicator
6 Mix Low Indicator
7 Select (SEL) Key
8 Manager Menu Key
9 Brush-Clean Counter
10 Arrow Keys
5
6
7
8
9
10
4
3
2
1

5-2
USER INTERFACE
Model C708 - WAWA User Interface
5
Symbol Definitions
To better communicate in the international arena,
symbols have replaced words on many of our operator
switches, function, and fault indicators. Your Taylor
machine is designed with these international symbols.
The following chart identifies the symbol definitions.
= Select
= Up Arrow
= Down Arrow
= Auto
=Heat Cycle
= Wash
= Mix Low
= Mix Out
= Menu Display
= Mix Pump
= Standby
Power Switch
When placed in the ON position, the power switch allows
control panel operation.
Liquid Cyrstal Display (LCD)
The LCD is on the front control panel. During normal
operation the display is blank. The display is used to
show menu options and notifies the operator if a fault is
detected. On international models, the display indicates
the temperature of the mix in the hopper.
Indicator Lights
Mix Low—When the Mix Low key is illuminated, the
mix hopper has a low supply of mix and should be refilled
as soon as possible.
Mix Out—When the Mix Out key is illuminated, the
mix hopper has been almost completely exhausted and
has an insufficient supply of mix to operate the freezer. At
this time, the Auto mode is locked out and the freezer is
placed in the Standby mode. To initiate the refrigeration
system, add mix to the mix hopper and press the Auto
key . The freezer will automatically begin operation.
Heat Mode—When the Heat mode key is illuminated,
the freezer is in the process of a Heat cycle. If enabled,
the Heat key can be pressed to start a Heat cycle. If
disabled, the Heat key is inoperable. By default, the
HEAT key is enabled.
BRUSH-CLEAN COUNTER—When the BRUSH CLEAN
COUNTER display has counted down to 1, the machine
must be disassembled and brush-cleaned within 24
hours.
Reset Mechanism
The RESET button is in the service panel on the left side
of the C708. The RESET button protects the beater
motor from overloading. Should an overload occur, the
reset mechanism will trip. To properly reset the freezer
place the power switch in the OFF position. Press the
RESET button firmly. Turn the power switch to the ON
position. Press the WASH key and observe the
freezer's performance.
CAUTION! DO NOT use metal objects to press
the reset button. Failure to follow this instruction may
result in electrocution.