teca AHP-1200MSP User manual

THREE PLACE DECIMAL
BEND
TECA CORPORATION IS PROHIBITED.
DRAWN
S1098
SK170710
10/10/17
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
AHP-1200MSP
TOLERANCING PER:
AA
TWO PLACE DECIMAL
INTERPRET GEOMETRIC COLD SHOE INSTALLATION
PROPRIETARY AND CONFIDENTIAL
NAME
DO NOT SCALE DRAWING
MATERIAL REV
A
FINISH
DWG. NO.
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
TECA CORPORATION.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
SHEET 1 OF 3
1) Carefully set the unit on it's back using the included insulating foam under the unit
to protect the power input module/switch.
2) Peel and remove the clear plastic film from the cold plate surface.
3) Carefully place the cold shoe assembly on the cold plate aligning the
(4) exterior holes on the cold shoe with the threaded inserts on the cold
plate. Make sure there is no foreign material between the cold plate
and the cold shoe.
4) Secure the cold shoe on the cold plate with (4) 6-32 x 5/8 socket head
cap screws, item #3142 & (2) 6-32 x 2 3/4 socket head cap screws, item
#4277. Tighten the screws using the provided Hex L-Key, item #4280.
Cold Shoe Assembly
socket head cap screw
Item #3142, 6-32 x 5/8
Item #4277, 6-32 x 2 3/4
socket head cap screw

DRAWN 10/10/17
UNLESS OTHERWISE SPECIFIED:
CHECKED
TECA CORPORATION IS PROHIBITED.
COLD SHOE INSTALLATION
SIZE
AHP-1200MSP
TOLERANCING PER:
AA
FINISH
DWG. NO.
DATE
PROPRIETARY AND CONFIDENTIAL
BEND
THREE PLACE DECIMAL
S1098
TWO PLACE DECIMAL
DO NOT SCALE DRAWING
SK170710 REV
INTERPRET GEOMETRIC
NAME
A
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
TECA CORPORATION.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
SHEET 2 OF 3
5) Remove the blue protective film from the Gap Pad and adhere the
tacky side to the cold shoe.
6) Insert the (4) Nylon sleeves item #4276 into the 1/2" DIA holes in the cold shoe.
7) Using the (4) sleeve bearings as a guide, slide the Cold Shoe Insulation
items #S1080, in place.
8) Using (4) 10-32 socket head cap screws, item #4278, secure the
cold shoe insulations in place. Tighten the 10-32 bolts using the
included Hex L-key, item #4281.
socket head cap screw
Item #S1080, Cold Shoe Insulation
Item #4278, 10-32 x 2

Item #4259, shoulder screw
Item #S1097, strap assembly
Insulating Foam
9) Turn the unit right side up.
10) Remove (4) 6-32 truss head screws from sides of the apron
(2 per side).
11) Install (4) 6-32 shoulder screws, item #4259, in place of the (4)
truss head screws removed in the previous step.
12) Place the beaker/bottle inside the cold shoe and place the
insulating foam in front of the beaker.
13) Use (2) strap assemblies, Item #S1097, and the foam to hold
the beaker firmly in place against the cold shoe.
INTERPRET GEOMETRIC COLD SHOE INSTALLATION
SIZE
CHECKED
AA
FINISH
DWG. NO.
TECA CORPORATION.
WITHOUT THE WRITTEN PERMISSION OF
TOLERANCING PER:
PROPRIETARY AND CONFIDENTIAL
DRAWING IS THE SOLE PROPERTY OF
TECA CORPORATION IS PROHIBITED.
SK170710
S1098
DO NOT SCALE DRAWING
DRAWN 10/10/17
DATE
THE INFORMATION CONTAINED IN THIS
A
THREE PLACE DECIMAL
SHEET 3 OF 3
MATERIAL
ANY REPRODUCTION IN PART OR AS A WHOLE
NAME
REV
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH BEND
TWO PLACE DECIMAL AHP-1200MSP
UNLESS OTHERWISE SPECIFIED: