Technaxx TX-22+ User manual

1
Technaxx®* User Manual
Bluetooth Vinyl Record and Cassette Converter TX-22+
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares that this device,
to which this user manual belongs, complies with the essential requirements of the
standards referred to the Directive RED 2014/53/EU. The Declaration of Conformity you
find here: www.technaxx.de/ 
the device the first time, read the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from German
fixed-line and 42 cent/minute from mobile networks).
Free Email: [email protected]
Keep this user manual for future reference or product sharing carefully. Do the same with
the original accessories for this product. In case of warranty, please contact the dealer or
the store where you bought this product. Warranty 2 years
Before usage
Choose the installation location of your unit carefully. Avoid placing it in direct
sunlight or close to a source of heat. Also avoid locations subject to vibrations and
excessive dust, heat, cold or moisture.
Do not install the unit in a inclined position, It is designed to be operated in a
horizontal position only.
If the unit is brought directly from a cold to a warm location, moisture may condense
inside the player, and cause damage it. When you first install the unit, or when you
move it from a cold to a warm location, wait for 30 minutes before operating the unit.
The ventilation holes should not be covered. Make sure there is enough space
above and beside the amplifier/receiver. Do not place a CD player or other equipment
on top of the device.
Do not open the cabinet. This might cause a damage to circuitry or electrical shock.
If you are not going to use the player for long time, be sure do disconnect the player
from the AC power source. When removing the power plug, never yank the cord.
To prevent fire or shock hazard, disconnect your unit from the AC power source
when cleaning. Use caution when cleaning and wiping the plastic parts. Do not attempt
to clean the unit with the chemical solvents as this might damage the finish.
V2.0

2
Features
Digitizing vinyl records & audio cassettes to USB or SD card up to 32GB
Music playback & recording via Bluetooth 4.2
Recording from external devices via AUX-IN connection
Music files: recoding (MP3) & playback (MP3/WMA) from USB or SD card
up to 32GB
No computer/notebook required
RCA outputs for connection to HiFi systems
Record player with automatic stop & 3 speeds: 33, 45, 78 rpm
Built-in cassette player
Built-in stereo loudspeakers
LED display with backlight
Functional and easy handling
Technical specifications
Bluetooth
V4.2 / profil A2DP & HFP / distance ~10m open areas
Bluetooth transmitting frequency 2.4GHz
Radiated output power max. 2.5mW
Mode
Phono, Cassette, USB, SD card, AUXIN, Bluetooth
Lautsprecher
2x 3W stereo (Ø= 7cm), SNR ≦80dB, impedance 4
Frequency range
Speakers 80Hz15kHz
Recording
MP3 music files on USB or SD card up to 32GB
Playback
MP3/WMAmusic files from USB or SD card up to 32GB
Mechanics
Belt-drive
Semi-automatic play tone pickup arm
Ceramic stereo cartridge with sapphire stylus
Connections
3.5mm AUX-IN jack & 3.5mm headphone jack
2x RCA outputs for connection to HiFi systems 400mV
USB port & SD card slot (up to 32GB)
Input device
DC12V / 2A
Material
MDF + PVC + Plastic
Weight/Dimensions
3kg / (L) 32.3 x (W) 31.1 x (H) 13.2cm
Package Contents
Bluetooth Vinyl Record and Cassette Converter TX-22+,
Adapter for small vinyl records with 45 RPM, Power
adapter DC12V/2A, User Manual

3
Product Overview
Front View
1
Dust cover
9
USB port
2
Source/ Mode (USB/SD)
10
LCD display
3
Record button
11
Play/Pause button
4
Function selector
12
Stop button
5
AUXIN jack
13
Volume knob / ON / OFF
6
Delete button
14
Next/ Skip up button
7
3.5mm headphone jack
15
Previous/ Skip down button
8
Rep/Ran (Repeat /Random)
16
SD card slot

4
Top View
20
Right speaker
24
Speed selectors (33/45/78 rpm)
21
45 rpm adaptor
25
Tone arm
22
Lift lever
26
Cassette player
23
Auto stop control

5
Rear View
27
RCA output
28
DC connection 12V/2A
First start
Carefully read the user manual. Insert the power adapter of the device into a
socket with AC 220240V and the other side to the TX-22+. Be reminded:
-
Attach the dust cover to the holder. Just slide the cover slowly and carefully
over the holder on the back of the TX-22+. You will hear a click when the cover
is safely attached.
Phono Mode
IMPORTANT! When using the turntable:
Make sure to remove the stylus protector, as illustrated on the left picture (it
should easily slide off the stylus assembly).
Make sure to unclip the tone arm lock before use and to secure it again after
use.
1
Cartridge
2
Needle protection

6
Playing in Phono mode (Vinyl)
1. Open the dust cover. Turn the volume knob (14) to turn the device on.
2. Use the function selector (4) to select PHONO mode.
3. Set the speed selector to the appropriate position: 33, 45 or 78, depending
on the record to be played.
4. Set the auto stop control to ON if you want the turntable to stop turning
when it has reached the end of the record. If the switch is set to OFF, the
turntable will continue turning at the end of the record.
5. Place the record on the turntable (use the 45 rpm adaptor, if required).
6. Remove the needle protection. Move the lift lever towards the back to raise
the tone arm from the arm park, then slowly move the arm to the record, as
illustrated on the right picture above. The turntable will start rotating.
7. Move the lift lever towards the front, the tone arm will gently drop onto the
record and playback will start.
8. To stop playback, move the lift lever towards the back to raise the tone arm.
The turntable will still be rotating but the record will stop playing. To continue
playback, move the lift lever towards the front.
9. To play a different piece on the record, move the lift lever towards the back,
move the raised tone arm to the start of the piece and then move the lift lever
towards the front to lower the tone arm and start playback.
10. To adjust the volume level, turn the volume knob to the right or left.
11. At the end of the record, move the lift lever towards the back to raise the
tone arm and move it back to the tone arm park, and then move the lift lever
towards the front to lower the arm onto its rest.
12. Alternatively, lift the tone arm off the record and return it to the arm rest
manually.
13. When you have finished playing records, engage the tone arm lock to
protect it from accidental movement. Turn the volume knob switch the unit off.
Unplug it from the power supply if you are not going to use it for a while.
NOTE: Should your record stop before the last track finishes, set the auto stop
control to OFF. Your record will now play to the end, but you will have to stop
the turntable rotation manually. (Return the tone arm to its rest manually and if
the turntable is still rotating, switch off the unit by pressing the volume control
knob. Then set the auto stop control back to ON.)

7
Recording in Phono mode (Vinyl)
Firstly insert memory device (USB drive or SD card). When turntable is
working, press the REC key on the top control board of the unit, (between step
5 and 7 from         USB or SD
symbol is flashing. To finish the work just need to press the STOP key.
How to replace a needle
Removing the needle from the
cartridge:
Inserting the needle:
1. Guide Pins (inside)
Place a screwdriver at the tip of the
needle heads hell and push
downwards in the direction shown in
  Remove the needle head
shell by pulling it forwards and pushing
downwards.
Hold the tip of the needle head shell
and insert it by pressing in the direction
     
head shell upwards in the direction

into the tip position.

8
Tape Mode When using the cassette player:
Make sure to insert the cassette in
the correct direction.
To avoid damaging the cassette, we
strongly recommend
taking it out of the device after playing
the cassette.
Playing a cassette
1. Turn the volume knob (14) to turn the device on.
2. Use the function selector (4) to select TAPE/AUX mode.
3. Insert a cassette with the tape facing away from you, as illustrated in the
picture above. The EJECT/FAST FORWARD button will pop out and the
system will start playing the tape automatically.
4. Turn the volume knob to your desired level.
5. To fast forward the cassette tape, press the EJECT/FAST FORWARD
button halfway down while the cassette is playing. The tape will be advanced
forward rapidly.
6. To resume normal playback, slightly press the EJECT/FAST FORWARD
button again. The button will fully pop out again.
7. To stop playback, press the EJECT/FAST FORWARD button completely.
Playback will be stopped and the cassette tape will be ejected.

9
Record a cassette
1. Set the function button to TAPE/AUX mode and then insert a memory
device (USB drive or SD card).
2. Press the record REC button, it will take 3 - 4 second to read the memory
device, then the USB or SD icon will be flashing on the LCD display.
3. Music will be recorded to the last inserted flash drive (USB or SD).
4. The system will start the recording mode after a few seconds. Insert your
cassette into the playback slot. During encoding, the USB or SD icon will be
flashing on the display.
5. To finish the recording
and return to TAPE/AUX mode.
NOTE:
The recording speed is 1:1. Recording will take as long as playing the
cassette.
The recording format is preset at MP3 bit rate 128Kbps.
AUX-IN Mode
Reproduction via AUX-IN
1. Turn the volume knob (14) to turn the device on.
2. Use the function selector (4) to select TAPE/AUX mode, then connect the
external audio device (such as a CD player, Smartphone, etc.) to the AUX-IN
socket at the front of the device. The audio signal from the external audio
device will now be played through the system.
3. If an external audio device is connected to the AUX IN socket, playing of the
AUXIN mode takes priority over cassette playback.

10
Recording AUX IN
1. Set the function button to TAPE/AUX mode and then insert a memory
device (USB drive or SD card).
2. Press the record REC button, it will take 3 - 4 second to read the memory
device, then the USB or SD icon will be flashing on the LCD display.
3. Music will be recorded to the last inserted flash drive (USB or SD).
4. The system will start the recording mode after a few seconds. Insert your
cassette into the playback slot. During encoding, the USB or SD icon will be
flashing on the display.
5. To finish the record
and return to TAPE/AUX mode.
NOTE:
The recording speed is 1:1. Recording will take as long as playing the CD
(or other auxiliary input).
The recording format is preset at MP3 bit rate 128Kbps.
To enjoy the function, user need to select the function switch to AUX-IN
position, and AUX-IN source will be prior to tape play.
When you insert both USB drive and SD card, the recorded file will be saved
into the latter inserting device.
The USB Port and SD Card Slot
The system is able to
decode and playback all
MP3/WMA files stored in
the memory media
connected to the USB
port or SD card slot.

11
Playback MP3/WMA format via USB device or SD card
1. Turn the volume knob (14) to turn the device on.
2. Following the illustration above, insert a USB device face up into the USB
port, making sure it is fully inserted. Alternatively, insert a memory card in the
direction of the arrow (as shown on the label next to the memory card slot),
making sure to insert it straight without bending.
IMPORTANT: Connecting the USB device upside down or backwards could
damage the audio system or storage media (USB drive, SD card). Check to
ensure the direction is correct before connection.
3. Set the function selector to USB/SD mode. (If you have both a USB device
and a memory card inserted, press the MODE button to toggle between USB
and SD mode.) The system will start reading the storage medium
automatically after mode selection and will display the total number of
MP3/WMA files.
4. The system will then start audio playback from the media storage device
(USB or SD card) automatically.
Playback from Bluetooth enabled Smartphone’s
1. Turn the volume knob (14) to turn the device on.
2. Set the function selector (4) to BT mode.
3. Open the Bluetooth on your Smartphone and search for the Bluetooth name
“Technaxx TX-22+“ to connect.
4. When successfully connected you hear a confirmation sound.
5. Select NEXT+ or PREV(Skip+ or Skip), Play/Pause key, to navigate to
your playlist.
Note:
Under this function, turntable function will be stopped automatically.
When you turn on the device and activate  again, the last
connected Smartphone will be connected automatically!

12
Playback controls
PLAY/PAUSE: Press this button once to stop playing, press it again to
continue.
STOP: Press this button to stop audio playback, the display will then show the
total number of MP3/WMA files.
SKIP UP/NEXT: Press this button once to play the next file, press and hold
this button to fast forward through the files/tracks.
SKIP DOWN/PREVIOUS: Press this button once to play the previous file,
press and hold this button to fast reverse through the files/tracks.
MODE: Press this button to toggle between USB and SD Card mode.
Important notes:
The system can detect and read files in MP3 / WMA format only via the USB
port or SD card slot.
You can connect an MP3 player to the system via the USB socket; however,
some MP3 players may not be able to play via the USB socket. This is due to
variances in the MP3 encoding format; it is not a malfunction of the system.
There are numerous USB and SD device producers and their products vary
in solution and format. We therefore cannot guarantee that this unit will
support all USB and SD devices from every brand.
This system supports USB drives/SD cards up to 32GB.
MP3 / WMA track format requirements: MP3 bit rate: 32 Kbps~256 Kbps;
WMA bit rate: 32 Kbps~320 Kbps.

13
Deleting files (USB/SD card)
The system is able to erase files stored on the USB drive or SD card. You can
delete a single file/track on the storage medium.
Deleting a single file/track
1. Insert the USB storage device or SD card, then select USB/SD mode (as
described previously).
2. Press the delete DEL button during the playback of the track you want to
delete: The title number will be flashing on the display. Press the delete DEL
button again to confirm.
Removing the USB flash drive or SD card
First move the function selector (4) to another mode (phono or cassette),
then turn the volume knob (14) to turn off the power.
To remove the USB flash drive, pull it out of the USB port.
To remove the SD memory card, pull it out of the SD card slot.
Amplifier connection (if required)
While listening to your new turntable using the built in speakers you may
wish to connect it to your existing HiFi system.
Connect the audio plugs to the Line input on your mixer or amplifier using an
RCA cable (*not included)
Red plug into R channel input.
White plug into L channel input.

14
FAQs
If you are experiencing problems with your USB Turntable with Cassette Deck,
check in the section below whether there are any quick and easy checks you
can do that may help you solve the problem. If you cannot solve the problem
by yourself, contact our after sales support line for advice. Do not attempt to
open, repair or modify the device yourself.
The device will turn into standby mode automatically after not playing music
for 10 minutes. To wake it up from standby mode move the function selector
(4).
Problems with sound
Clockwise rotate the power/volume knob to increase the volume.
Make sure the power cord of the device is connected to an appropriate
electrical outlet and make sure the wall socket is switched on.
Make sure the function switch is set to your desired function: PHONO,
TAPE/AUX, USB/SD, BT.
When playing records, make sure you have selected the correct speed (33,
45 or 78 rpm).
When playing a cassette, make sure it is properly inserted.
When playing a CD via the AUX IN connection, make sure the cable is firmly
connected, all controls on the CD player are properly set, the disc tray is
closed and the disc is clean and undamaged.
When playing music from a USB device (or SD card), make sure the
memory device is properly inserted in the USB port (SD card slot) and the
correct MODE is selected.
Electrical safety and cord handling
Before installing this device, make sure your outlet voltage corresponds to
the voltage stated on the appliance rating label.
To prevent contact with high voltage components inside, do not attempt to
open the device.
When connecting the device, align the plug properly and insert it fully to
prevent electric shock.

15
Only use this device with the cord and plug supplied, and do not overload
the power outlet.
If the power cord is damaged, do not use the device. The cord must be
replaced by the manufacturer or similarly qualified personnel in order to avoid
a hazard.
Note:
We advise you to clean your records with an anti-static cloth to gain
maximum enjoyment from them and to make them last. We would also point
out that for the same reason your stylus should be replaced periodically
(approximately every 250 hours) Dust the stylus from time to time using a very
soft brush dipped in alcohol (brushing from back to front of the cartridge).
When transporting your LP player do not forget to: 1. Replace the protective
cap on the stylus. 2. Put the rest clip into the pick-up arm.

16
Reattaching the turntable belt-drive
The turntable drive belt is factory fitted - use these instructions only if the
turntable fails to revolve.
STEP 1
Remove the turntable anti-slip mat
from the platter. looking through one
of the holes in the platter, check if
the belt has indeed come off the
turntable pulley. Use a screwdriver
-clip (iron
binder) and lift the turntable off the
Turntable mechanism.
Rubber
Drive Belt
Pull belt out gently
Brass Pulley
STEP 2
Retrieve the dropped black rubber
band (the drive belt) and place it
around the platter base - then pull
the belt out gently without
overstretching. Turn the platter over
while holding on to the belt.
STEP 3
Looking through one of the holes in
the platter, locate the small Brass
Pulley (the pulley is attached to the
turntable motor). Then proceed to
hook the pulled out part of the rubber
belt by hand around the Pulley and
then line up the Centre of the platter
with the silver turntable spindle.
Lower the platter gently onto the
deck and let go until it is back in
position.
STEP 4
When the urntable platter is in the
correct position, check the belt is still
around the pulley and then replace
-clip to secure the turntable to
the spindle.
Hints for Environment Protection: Packages materials are
raw materials and can be recycled. Do not disposal old devices
or batteries into the domestic waste. Cleaning: Protect the
device from contamination and pollution (use a clean drapery).
Avoid using rough, coarse-grained materials or solvents/
ggressive cleaner. Wipe the cleaned device accurately.
Distributor: Technaxx Deutschland GmbH & Co.KG, Kruppstr.
105, 60388 Frankfurt a.M., Germany

17
Technaxx®* Gebrauchsanleitung
Bluetooth Platten- und Kasettendigitalisierer TX-22+
Hiermit erklärt der Hersteller Technaxx Deutschland GmbH & Co.KG, dass sich dieses
Gerät, zu dem diese Bedienungsanleitung gehört, in Übereinstimmung mit den
grundlegenden Anforderungen der Normen gemäß Richtlinie RED 2014/53/EU. Hier finden
Sie die Konformitätserklärung: www.technaxx.de/ (in der unteren Leiste unter
Vor dem ersten Gebrauch lesen Sie die Gebrauchsanleitung
sorgfältig durch.
Telefonnummer für den technischen Service: 01805 012643 (14 Cent/Minute aus dem
deutschen Festnetz und 42 Cent/Minute aus Mobilfunknetzen).
Kostenfreie E-Mail: [email protected]
Die Gebrauchsanleitung für zukünftige Bezugnahme oder eine Produktweitergabe
sorgfältig aufbewahren. Verfahren Sie ebenso mit dem Originalzubehör dieses Produktes.
Im Garantiefall wenden Sie sich bitte an den Händler oder das Ladengeschäft, wo Sie
dieses Produkt gekauft haben. Garantie 2 Jahre
Vor dem Gebrauch
Wählen Sie den Standort Ihres Geräts sorgsam aus. Setzen Sie das Gerät keiner
direkten Sonneneinstrahlung aus, und platzieren Sie es nicht in der Nähe von
Wärmequellen. Vermeiden Sie Standorte, an denen das Gerät Schwingungen sowie
übermäßigem Staub, Hitze, Kälte und Feuchtigkeit ausgesetzt ist.
Stellen Sie das Gerät nicht auf eine unebene Fläche, da es nur für eine Verwendung in
horizontaler Position konzipiert wurde.
Wurde das Gerät direkt Kälte oder Wärme ausgesetzt, kann Feuchtigkeit im Gerät
kondensieren und es beschädigen. Wenn Sie das Gerät zum ersten Mal installieren, oder
wenn Sie es von einem kalten Ort an einen warmen Ort bringen, warten Sie 30 Minuten,
bevor Sie das Gerät in Betrieb nehmen.
Die Lüftungslöcher dürfen nicht verdeckt sein. Vergewissern Sie sich, dass ausreichend
Platz über und neben dem Verstärker/Receiver gegeben ist. Stellen Sie weder einen
CD-Player noch andere Geräte auf das Gerät.
Öffnen Sie nicht das Gehäuse. Dies könnte Schäden am Schaltkreis oder einen
Stromschlag verursachen.
Wenn Sie das Gerät längere Zeit nicht benutzen, trennen Sie es von der Stromquelle.
Um den Stecker von der Steckdose zu trennen, niemals am Kabel ziehen.
Um Feuer oder einen Stromschlag zu vermeiden, trennen Sie das Gerät vor dem
Reinigen von der Stromquelle. Seien Sie vorsichtig, während Sie die Kunststoffteile
reinigen und abwischen. Das Gerät nicht mit chemischen Reinigungsmitteln reinigen, da
diese die Oberfläche beschädigen könnten.
V2.0

18
Besonderheiten
Digitalisieren von LPs & Audiokassetten auf USB oder SD-Karte bis 32GB
Musikwiedergabe via Bluetooth 4.2
Aufnahme von externen Geräten über AUX-IN Anschluss
Musikdateien: Aufnahme (MP3) & Wiedergabe (MP3/WMA) von USB oder
SD-Karte bis 32GB
Kein Computer/Notebook erforderlich
Cinch-Ausgänge (RCA) zum Anschluss an HiFi-Systeme
Plattenspieler: automatischer Stopp, 3 Geschwindigkeiten: 33, 45, 78 U/Min.
Eingebautes Kassettendeck
Eingebaute Stereo-Lautsprecher
LED-Anzeige mit Hintergrundbeleuchtung
Funktionale und einfache Bedienung
Technische Daten
Bluetooth
V4.2 / Profil A2DP & HFP / Reichweite ~10m offene Bereiche
Bluetooth Übertragungsfrequenz 2,4GHz
Abgestrahlte Ausgangsleistung max. 2,5mW
Modus
LP, Kassette, USB, SD-Karte, AUXIN, Bluetooth
Lautsprecher
2x 3W stereo (Ø= 7cm), SNR ≦80dB, Impedanz 4
Frequenzbereich
Lautsprecher 80Hz15kHz
Aufnahme
MP3-Musikdaten auf USB oder SD-Karte bis 32GB
Musikwiedergabe
von USB & SD-Karte bis zu 32GB
(MP3-, WMA-Musikdateien)
Mechanik
Riemenantrieb
Halbautomatischer Tonarm
Keramischer Tonabnehmer mit Saphirabtastnadel
Verbindungen
3,5mm AUX-IN & 3,5mm Kopfhöreranschluss
2x Cinch-Ausgänge (RCA) zum Anschluss an
HiFi-Systeme 400mV
USB-Anschluss & SD-Kartenfach (bis 32GB)
Eingangspower
DC12V / 2A
Material
MDF + PVC + Kunststoff
Gewicht / Maße
3kg / (L) 32,3 x (B) 31,1 x (H) 13,2cm
Verpackungsinhalt
Bluetooth Platten- & Kassettendigitalisierer TX-22+,
Adapter für Single-Vinylschallplatten mit 45 U/min, Netzteil
DC12V/2A, Gebrauchsanleitung

19
Produktübersicht
Vorderansicht
1
Kunststoffabdeckung
9
USB-Anschluss
2
Quelle/Modus (USB/SD)
10
LCD-Bildschirm
3
Aufnahmetaste
11
Wiedergabe-/Pause-Taste
4
Funktionswahlschalter
12
Stopp-Taste
5
AUX-Eingang
13
Lautstärkeregler / EIN / AUS
6
Löschtaste
14
Weiter-/Überspring-Taste
7
3,5mm Kopfhöreranschluss
15
Zurück-/Überspring-Taste
8
Rep/Ran (Wiederholen/Zufällig)
16
SD-Kartensteckplatz

20
Draufsicht
20
Rechter Lautsprecher
24
Drehzahlwähler (33/45/78 U/min)
21
Adapter für 45 U/min
25
Tonarm
22
Hubhebel
26
Kassettenrekorder
23
Automatische Stoppsteuerung